Onicon F-5000 Instrucciones de funcionamiento

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727)442-5699

www.onicon.com • [email protected]

F-5000 View Software

Installation and Operation Guide

10-16

2032-1 / 107050 Rev B

CON

Flow and Energy Measurement

This publication must be read in its entirety before performing any operation. Failure

to understand and follow these instructions could result in serious personal injury

and/or damage to the equipment. Should this equipment require repair or adjustment

beyond the procedures given herein, contact the factory at:

ONICON, INC.

11451 BELCHER ROAD SOUTH

LARGO, FL 33773 USA

TELEPHONE: +1 (727) 447-6140

FAX: +1 (727) 442-5699

EMAIL: [email protected]

Download Technical Data Sheets from our website:

www.onicon.com

ONICON believes that the information provided herein is accurate however be

advised that the information contained herein is NOT a guarantee for satisfactory

results. Specifically, this information is neither a warranty nor guarantee,

expressed or implied, regarding performance; merchantability; fitness; or any

other matter with respect to the products; nor recommendation for the use of

the product/process information in conflict with any patent. Please note that

ONICON, Inc. reserves the right to change and/or improve the product design and

specification without notice.

ONICON F-5000 Manuals:

• Model F-5400 Instruction Manual

• Model F-5500 Instruction Manual

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699 • [email protected]

F-5000 Software Manual 10/16 - 2032 / 107050 Page 2

Notice

F-5000 View

ONICON

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699 • [email protected]

F-5000 Software Manual 10/16 - 2032 / 107050 Page 3

Table Of Contents

F-5000 View™

TABLE OF CONTENTS

1. Introduction Page 5

2. Installation Page 6

3. Operation Page 9

a. Main Screen Page 9

b. Charts Settings Page 11

c. Conﬁgure Page 13

d. Data Logger Page 19

e. Simulation Mode Page 21

f. Zero CAL-CHECK®Test Page 23

g. Zero CAL-CHECK®Certiﬁcate Page 23

4. Glossary of Terms and Abbreviations Page 26

5. Index Page 27

F-5000 View

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699 • [email protected]

F-5000 Software Manual 10/16 - 2032 / 107050 Page 4

F-5000 View

INTRODUCTION

www.onicon.com

Introduction

To ensure correct use of the software, please read this manual thoroughly.

Regarding this Manual:

• This manual should be passed on to the end user.

• Before use, read this manual thoroughly to comprehend its contents.

• The contents of this manual may be changed without prior notice.

permission.

• All reasonable effort has been made to ensure the accuracy of the contents of this manual. However, if any

errors are found, please inform ONICON.

• ONICON assumes no responsibilities for this product except as stated in the warranty.

• If the customer or any third party is harmed by the use of this product, ONICON assumes no responsibility

for any such harm owing to any defects in the product which were not predictable, or for any indirect

damages.

Safety Precautions:

The following general safety precautions must be observed during all phases of installation, operation,

service, and repair of this product. Failure to comply with these precautions or with specific WARNINGS

given elsewhere in this manual violates safety standards of design, manufacture, and intended use of

the product . ONICON Incorporated assumes no liability for the customer's failure to comply with these

requirements. If this product is used in a manner not specified in this manual, the protection provided by

this product may be impaired.

The following symbols are used in this manual:

Introduction: Safety Information

Messages identified as "Caution" (refer to accompanying documents) contain

information regarding potential damage to the product or other ancillary products.

Messages identified as "Warning" contain information regarding the personal safety of

individuals involved in the installation, operation or service of this product.

Messages identified as "Note" or "Important Note" contain information critical to the

proper operation of the product.

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699 • [email protected]

F-5000 Software Manual 10/16 - 2032 / 107050 Page 5

Introduction

Thank you for purchasing the Model F-5000 series Thermal Gas Mass Flow meter

from ONICON. An extensive engineering effort has been invested to deliver advanced

features, accuracy measurement performance, and outstanding reliability.

The F-5000 View software allows users to easily display data and configure the

F-5000 to their specific application parameters. Then, log flow/temperature data to an

Excel file.

Note: For the Model F-5500 flow meter only, the software can also access the

Calibration Validation diagnostic function using the Zero CAL-CHECK®test.

This Manual contains the installation and operation instructions for the F-5000 View

Software.

This manual is divided into the following sections: Introduction, Installation, Operation,

Glossary and Index.

Introduction

F-5000 View

INSTALLATION

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699 • [email protected]

F-5000 Software Manual 09/16 - 2032 / 107050 Page 6

Fig. 2.2: F-5000 View Software Icon

Installation

Open the enclosure of your F-5000 series flow meter as instructed in your meter's

instruction manual. Connect the flow meter to a PC or laptop using the mini USB port

(type A, mini cable). If the PC is connected to the Internet and running Windows

7/8™, the PC will try to automatically load the VCP driver. If the driver does not load

automatically, download the VCP driver at:

www.ftdichip.com/Drivers/VCP.htm

Note: The latest version of the F-5000 View software is available for download at www.

onicon.com/5500 or www.onicon.com/5400.

Fig. 2.1: Online Download Location for F-5000 View™ Software

F-5000 View

INSTALLATION

Installation

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699 • [email protected]

F-5000 Software Manual 09/16 - 2032 / 107050 Page 7

To install the F-5000 View program, run the "F-5000View_V#.##-setup.exe" file that

is located in the sub-folder of the downloaded file. After clicking "Next" the screen will

show:

Select the folder in which you wish to install F-5000 View, then click "Install".

When the program is done installing, you may exit, then restart your computer.

Note: The F-5000 View software will automatically detect the model type (F-5500 or

F-5400).

Note: Some features that are available on the F-5500 will not be available for the

F-5400 and will not appear as options to configure using this software program.

Installation

F-5000 View

INSTALLATION

Installation

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699 • [email protected]

F-5000 Software Manual 10/16 - 2032 / 107050 Page 8

COM Port Assignment

Be sure to have your F-5000 series flow meter connected by mini USB to a PC or

laptop before opening the F-5000 View software. Upon opening F-5000 View for the

first time, Windows will assign a "virtual COM port". The COM port number that has

been assigned will appear automatically in the drop down box.

If the correct COM Port does not appear, go to Control Panel/Device Manager and click

on Ports (COM & LPT). The COM port number should be displayed under the USB

symbol.

If prompted, enter the assigned COM port in F-5000 View by using the drop down

menu and press OK.

Note: The flow meter must be plugged into the computer in order for the system to

Fig. 2.3: COM Port Selection Window

Operation: Main Screen

Main Screen

F-5000 View

OPERATION

Installation

COM Port

Assignment

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699 • [email protected]

F-5000 Software Manual 10/16 - 2032 / 107050 Page 9

Model

F-5500

only

Main Screen

The image below depicts the main screen that appears upon entering F-5000 View.

Fig. 3.1: F-5000 View

™

Main Screen

Note: Data on the screen is refreshed at user selected update rate. See p. 11 for

more information on setting up Charts.

Charts Button

This calls up two charts that can be configured for either temperature or flow. Each

chart can be individually enlarged and rescaled from the original default settings. For

more information on how to change the charts settings, refer to "Operation: Chart

Settings" on page 11.

Note: It can be set for either automatic or manual scaling.

Operation: Main Screen

Main Screen

F-5000 View

OPERATION

11451 Belcher Road South, Largo, FL 33773 • USA • Tel +1 (727) 447-6140 • Fax +1 (727) 442-5699 • [email protected]

F-5000 Software Manual 10/16 - 2032 / 107050 Page 10

F-5000 View

OPERATION

Charts

Settings

Model F-5000

Operation: Main Screen

Main Screen Data Log

This function allows all selected data to be logged to an Excel file at the specified

sample time. All readings are time/date stamped. For more information on using the

Data Logger function, refer to "Operation: Data Logger" on page 20.

Configure

This allows the operator to go in and set the application parameters. This can be done

either via the F-5000 View software or manually via the instrument's display. For more

information on configuring application parameters, refer to "Operation: Configure" on

page 13.

Simulation

This function can be used to verify that all the flow meter outputs are working properly.

The easiest way to perform this check is to enter a specific temperature/flow rate. The

corresponding analog outputs can be verified using a DMM and using a watch for the

pulse. Refer to Page 21 for more information on how to use the Simulation function.

Zero CAL-CHECK® (available only on Model F-5500)

The Zero CAL-CHECK®calibration validation test can be performed while the unit is

still in the pipe (if a no flow condition can be established) or out of the pipe when zero

flow cannot be established. Zero CAL-CHECK®does the following:

• Checks for build-up on sensor that could affect calibration

• Further validates the zero stability of the meter

• Checks thermal conductivity (heat transfer) repeatability of the sensor

The Zero CAL-CHECK®calibration validation test is explained in greater detail on p.

23.

Note: Zero CAL-CHECK will not show up as an option for the Model F-5400.

Alarms

The unit can be configured for high/low alarms for either flow or temperature. The

"alarms window" displays any alarms or warnings.

Exit

Exit the application

Tabla de contenidos

Otros manuales de Instrumento de medición de Onicon

Onicon

Onicon SYSTEM-40 Instrucciones de funcionamiento

Onicon

Onicon F-3500 Instrucciones de funcionamiento

Onicon

Onicon D-100 Instrucciones de funcionamiento

Onicon

Onicon System-10 BTU Meter Manual de usuario

Onicon

Onicon System-10 BTU Meter Instrucciones de funcionamiento

Onicon

Onicon FT-4600 Instrucciones de funcionamiento

Onicon

Onicon F-4300 Instrucciones de montaje

Onicon

Onicon D-100 Instrucciones de funcionamiento

Onicon

Onicon F-4600 Series Instrucciones de funcionamiento

Onicon

Onicon FP-4400 Instrucciones de funcionamiento originales

Onicon

Onicon SYSTEM-40 Instrucciones de funcionamiento

Onicon

Onicon SYSTEM-20 Instrucciones de funcionamiento

Onicon

Onicon SYSTEM-30 Instrucciones de funcionamiento

Onicon

Onicon F-2500 series Instrucciones de funcionamiento

Onicon

Onicon F-1500 Series Instrucciones de funcionamiento

Onicon

Onicon F-1000 SERIES Guía de configuración

Onicon

Onicon SYSTEM-30 Instrucciones de funcionamiento

Onicon

Onicon D-100 Manual de usuario

Onicon

Onicon SYSTEM-20 Instrucciones de funcionamiento

Onicon

Onicon SeaMetrics EX90 Manual de usuario

Onicon

Onicon FT-3000 Series Manual de usuario

Onicon

Onicon System-10 BTU Meter Instrucciones de funcionamiento

Onicon

Onicon F-2600 Series Instrucciones de funcionamiento

Onicon

Onicon F-1100 Series Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario