One Forall URC-6210 Manual de usuario
Instruction manual . . . . .P. 2
Bedienungsanleitung . .s. 10
Mode d’emploi . . . . . . .P. 18
Guía del usario . . . . . . .P. 26
Manual de instruções . .P. 34
English
Deutsch
Français
Español
Português
Istruzioni per l’uso . . . .P. 42
Gebruiksaanwijzing . . .P. 50
Használati útmutató
.P. 58
Inst ukcja obsługi
. . . . .P. 66
Návod k použití
.......P.74
Italiano
Nederlands
Magyar
Polski
Česky
Universal remote
Universal Fernbedienung
Télécommande universelle
Mando a Distancia Universal
Telecomando Universal
Telecomando Universale
Universele Afstandsbediening
Unive zális távvezé lő
Uniwe salny pilot zdalnego ste owania
Unive zální dálkové ovládání
URC-6210/6211
706113_URC-6210-11_E_10t:Zapper_3 12-12-2007 11:56 Pagina 1
2WWW.ONEFORALL.COM
Table of Contents
INSTALLING T E BATTERIES 3
FEATURES AND FUNCTIONS 3
SET UP
(To set up the ZAPPER for your Television)
Direct code set up 4
Search Method 6
Code Blink Out 7
SET-UP CODES
Television 82
TROUBLES OOTING
Helpful Hints 8
English
706113_URC-6210-11_E_10t:Zapper_3 12-12-2007 11:56 Pagina 2
WWW.ONEFORALL.COM 3
Installing the batteries
The ZAPPER needs 2 new “AAAA” alkaline batteries.
1Remove the battery cover from the back of the ZAPPER by pressing down on
the tab.
2Match the batteries to the +/- marks inside the battery case, then insert the
batteries.
3Press the battery cover back into place.
Important notes:
- In order to avoid having to reprogram your ZAPPER after you
remove the batteries, you will need to insert new batteries within
5 minutes. Also, it is best that you do not use rechargeable batteries.
Features and Functions
1 POWER (red LED – Light Emitting Diode)
The POWER key operates the same function it did on your original remote
control. The LED underneath the POWER key will light up red whenever a
key is pressed.
2 C ANNEL +/-, VOLUME+/- and MUTE
The CH+/- and VOL+/- keys operate just as those on your original remote
control. These keys are also used to set up your ZAPPER.
3 MAGIC
The MAGIC key (= setup key) is used to set up your ZAPPER.
706113_URC-6210-11_E_10t:Zapper_3 12-12-2007 11:56 Pagina 3
4WWW.ONEFORALL.COM
Direct code set up
To set up the ZAPPER for your Television follow the instructions below.
1Find your Television code in the Set-Up Code section (page 82-107). Codes
are listed by brand name. The most popular codes are listed first.
2Make sure your TV is switched on (not on standby).
3Press and hold the MAGIC key until the LED blinks twice (The LED
underneath the POWER key will blink once then twice).
4Enter your 5-digit code according to the chart below.
The LED underneath the POWER key will blink twice.
5Now, aim the ZAPPER at your Television and press POWER. If your
Television switches OFF, your ZAPPER should be ready to operate your
device.
VOLUME + = 1
VOLUME - = 2
CHANNEL - = 4MUTE = 5
CHANNEL + = 3
706113_URC-6210-11_E_10t:Zapper_3 12-12-2007 11:56 Pagina 4
WWW.ONEFORALL.COM 5
6Turn your device back on and try all the remote’s functions to ensure they
are working properly. If the functions do not work properly, repeat steps
1-5 using another code listed under your brand.
For example: To enter a Sony TV code 33121, you would press CHANNEL +,
CHANNEL +, VOLUME +, VOLUME -, VOLUME +.
If your television does not respond to the ZAPPER after you have
tried all the codes listed for your brand, try the Search Method
described on page 6.
Make sure you write your correct 5 digit code in
the boxes provided on this page.
Important notes:
- Some codes are quite similar. If your television does not respond or
is not functioning properly with one of the codes, follow steps 1-5
with each code listed for your brand.
- If none of the codes listed for your brand operate your television,
follow the Search Method described in the next section. The Search
Method can be used even if your brand is not listed at all.
- Write the code for your TV in the boxes provided below for easy
future reference.
TV Code
■
■■
■■
■
■
■
■
■
706113_URC-6210-11_E_10t:Zapper_3 12-12-2007 11:56 Pagina 5
6WWW.ONEFORALL.COM
Search Method
If your Television does not respond to the ZAPPER after trying all the codes
listed for your brand, try searching for your code. To search for your TV code:
1 Turn on your TV.
2Press and hold the MAGIC key until the LED blinks twice
(The LED underneath the POWER key will blink once then twice).
3Next, press the MUTE, C ANNEL -, C ANNEL -.
4 Point the ZAPPER at your television. Next, alternate between POWER and
C ANNEL - until your Television turns off. You may have to press these
keys many times (up to 150!), so please be patient. Remember, you must
aim the ZAPPER at your device the entire time you are searching for your
code.
5 When your device turns off, press and release MAGIC to store the code.
The ZAPPER should now be ready to operate your Television. Turn your
device back on and try all the remote’s functions to ensure they are
working properly. If some of the ZAPPER’S commands are not operating
correctly, try the search method again, you may be using the wrong code.
706113_URC-6210-11_E_10t:Zapper_3 12-12-2007 11:56 Pagina 6
WWW.ONEFORALL.COM 7
Code Blink Out
After you have used the Search Method, you can find out which code
the ZAPPER responded to by blinking back the code. It’s handy to know
your Television code for future reference. Remember, you can only
blink back your code after the ZAPPER is operating your device.
To blink out your TV code:
1Press and hold the MAGIC key until the red LED blinks twice (the LED
underneath the POWER key will blink once then twice).
2 Next, press MUTE, C ANNEL -, C ANNEL +.
3 For the first digit of your 5-digit code, press VOLUME + and count the
red blinks.
4For the second digit, press VOLUME - and count the red blinks.
5For the third digit, press C ANNEL + and count the red blinks.
6 For the fourth digit, press C ANNEL - and count the red blinks.
7For the fifth digit, press MUTE and count the red blinks.
Write the code for your TV in the boxes provided on page 5.
706113_URC-6210-11_E_10t:Zapper_3 12-12-2007 11:56 Pagina 7
8WWW.ONEFORALL.COM
Problem:
Your brand is not listed in
the ONE FOR ALL code section?
The ONE FOR ALL does not
operate your television?
The ONE FOR ALL is not
performing commands
properly?
You cannot reach channel 10
and above on your TV.
The ONE FOR ALL does not
respond after pressing a key?
LED does not blink when you
press a key?
Solution:
Try the search method.
A) Try all the codes listed for your
brand.
B) Try the search method.
You may be using the wrong code.
Try Direct Set-Up again trying each
code listed under your brand or
start the search method over again
to locate the proper code.
If your original remote did not
have CHANNEL +/- keys, the ZAPPER
may not operate this function.
Make sure you are using new
batteries and are aiming the ONE
FOR ALL at your device.
Replace batteries with 2 new
“AAAA” alkaline batteries.
706113_URC-6210-11_E_10t:Zapper_3 12-12-2007 11:56 Pagina 8
WWW.ONEFORALL.COM 9
Customer Service
In the UK In Ireland
E-mail : ofahelp@uebv.com (*) E-mail : ofahelp@uebv.com (*)
Fax : +31 53 432 9816 Fax : +31 53 432 9816
Tel. : 0901-5510010
(£ 0,50 per minute)
Tel. : 016015986
In Australia In South Africa
Fax : 03 9672 2479 Fax : 011 298 2302
Tel. : 1 300 888 298 Tel. : 0860 100551
Tel. : 011 4173000
In New Zealand Ukraine
Fax : (06) 878 2760 Fax : +38 044 4890187
Tel. : 0508 ONE 4 ALL (663 4 255) Tel. : +38 044 4890188
Web. : www.oneforall.com.ua
Slovakia Croatia
Fax : +421 55 611 8111 Fax : +385 1 48 16 807
Tel. : +421 55 611 8131 Fax : +385 1 48 16 806
Web. : www.dsi.sk Web. : www.tehnocentar.hr
(*) Just send a blank message, you’ll get auto-reply.
706113_URC-6210-11_E_10t:Zapper_3 12-12-2007 11:56 Pagina 9
10 WWW.ONEFORALL.COM
Inhaltsverzeichnis
EINSETZEN DER BATTERIEN 11
FUNKTIONEN 11
EINSTELLUNG
(Einrichten des ZAPPERS für die Bedienung Ihres Fernsehger ts)
Manuelle Codeeingabe 12
Suchverfahren 14
Codeabfrage 15
EINSTELLCODES
Fernsehger t 82
FE LERBE EBUNG
Problem und Lösung 16
Deutsch
706113_URC-6210-11_E_10t:Zapper_3 12-12-2007 11:56 Pagina 10
Otros manuales para URC-6210
4
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Idiomas:
Otros manuales de Control remoto universal de One Forall
One Forall
One Forall URC-6211 Manual de usuario
One Forall
One Forall URC-6210 Manual de usuario
One Forall
One Forall URC-2505 Manual de usuario
One Forall
One Forall Kameleon Manual de usuario
One Forall
One Forall URC 7120 Manual de usuario
One Forall
One Forall SO EASY URC-2530 Manual de usuario
One Forall
One Forall URC-7711 Guía de inicio rápido
One Forall
One Forall URC 1810 Manual de usuario
One Forall
One Forall DVD EXPERT URC-4041 Manual de usuario
One Forall
One Forall URC-7781 Manual de usuario
One Forall
One Forall URC-3415 Manual de usuario
One Forall
One Forall URC-1666 Manual de usuario
One Forall
One Forall URC-7510 Manual de usuario
One Forall
One Forall URC-2981 Hoja de información del producto
One Forall
One Forall URC-7710 Manual de usuario
One Forall
One Forall URC-3720 Manual de usuario
One Forall
One Forall URC-1312 Manual de usuario
One Forall
One Forall KAMELEON 4 Manual de usuario
One Forall
One Forall URC8820N Manual de usuario
One Forall
One Forall URC-7940 Manual de usuario
