Omnitron Systems Technology IConverter XGT+ Manual de usuario

iConverter XGT+

Standalone Module User Manual

This User Manual describes the functions of the iConverter XGT+ Revision 2. The product

revision can be found on the label on the bottom of the module. The label is marked xx/yy,

where yy is the revision number.

Product Overview

The iConverter XGT+ is a 10 Gigabit Ethernet media converter with one 10GBASE-T RJ-45

port and one pluggable transceiver port that provides copper-to-ber and copper-to-copper

media conversion. Copper-to-ber conversion is achieved with XFP or SFP+ ber transceivers.

Copper-to-copper conversion is achieved with a CX4 XFP transceiver.

The XGT+ supports high-power (power level 4) XFP transceivers, and the latest generation

of wavelength tunable DWDM XFP transceivers.

Installation Procedure

1) Congure DIP-switches

2) Install Standalone Module and Connect Cables

3) Verify Operation

1) CONFIGURE DIP-SWITCHES

DIP-SWITCH BANK 1

The location of the DIP-switches is shown in

Figure 1.

The function of DIP-switch Bank is outlined in

Figure 2.

Switch DOWN

(Default) UP

SW1 Normal P1 Loopback Enabled

SW2 Normal P2 Loopback Enabled

SW3 Normal P2 Short Range

SW4 Normal P1 Built-In Self Test (BIST)

Figure 2: DIP-switch BANK 1 Denitions

SW1 - P1 LOOPBACK “P1-LB”

When this DIP-switch is in the DOWN position (factory default), port P1 loopback is disabled.

When this DIP-switch is in the UP “P1-LB” position, loopback is enabled on port P1. When

enabled, all data received on port P1 is transmitted out port P1 and the connection between

port P1 and port P2 is interrupted.

NOTE: Simultaneous loopback of port P1 and port P2 is not supported on XFP models.

Page 1

SW2 - P2 LOOPBACK “P2-LB”

When this DIP-switch is in the DOWN position (factory default), port P2 loopback is disabled.

When this DIP-switch is in the UP “P2-LB” position, loopback is enabled on port P2. When

enabled, all data received on port P2 is transmitted out port P2 and the connection between

port P2 and port P1 is interrupted.

NOTE: Simultaneous loopback of port P1 and port P2 is not supported on XFP models.

SW3 - P2 Short Range

When this DIP-switch is in the DOWN position (factory default), port P2 short range feature

is disabled. When disabled, port P2 will support up to 100 meters of CAT 6A cabling. When

this DIP-switch is in the UP “P2-SR” position, port P2 will support up to 30 meters of CAT 5E

or better cabling in a reduced power consumption mode. The SR LED will be illuminated

indicating Short Range is enabled.

SW4 - P1 BIST (SFP+ Model Only)

When this DIP-switch is in the DOWN position (factory default), port P1 Built-In Self Test is

disabled. When this DIP-switch is in the UP “P1-Tst” position, the port will transmit a Pseudo

Random Bit Sequence (PRBS).

When two XGT+ converters are connected via port P1 (Port 1 to Port 1), the BIST function is

supported. The XGT+ initiating BIST (DIP-switch SW4 UP) will generate and send a PRBS

pattern out Port 1 to the other module. The receiving XGT+ will detect a good test pattern

and return a PRBS acknowledgement test pattern back to the initiating XGT+.

A successful test will produce a green blinking (5Hz) P1 LB LED on the initiating XGT+ and

a green blinking (1Hz) P1 LB LED on the receiving XGT+. If the initiating XGT+ does not

receive a valid response, the P1 LB LED will be blinking amber (5Hz). When BIST is initiated,

the trafc received on Port 2 of both converters will be discarded.

If loopback has been initiated, the BIST DIP-switch will be ignored. If BIST has been initiated,

the loopback DIP-switches will be ignored.

NOTE: The XGT+ modules must be the same revision for the BIST function to operate

correctly.

DIP-SWITCH BANK 2

LINK MODES

SW1 and SW2 - LINK MODES

These DIP-switches configure the different link modes available on the XGT+. It is

recommended to have link modes set to Link Segment (default setting - all DOWN) during

the initial installation. After the circuit has been tested and operational, congure the module

for the desired mode. Refer to Figure 3 for conguration options.

SW1 SW2 Function

DOWN DOWN Link Segment (default)

UP DOWN Asymmetrical Link Propagate P1 to P2

DOWN UP Asymmetrical Link Propagate P2 to P1

UP UP Symmetrical Link Propagate

Figure 3: DIP-switch BANK 2 Link Modes

For detailed information on the operation of the different Link Modes, download the application

note “iConverter Link Modes” available on Omnitron’s web page:

http://www.omnitron-systems.com/downloads_iconverter.php

Page 2

Page 3

SW3 and SW4 - RESERVED

These DIP-switches are for factory use only and must always remain in the DOWN (factory

default) position.

2) INSTALL STANDALONE MODULE AND CONNECT CABLES

a. The XGT+ is available as a standalone module with built-in mounting brackets. For

wall-mounting, attach the XGT+ to a wall, backboard or other at surface. For tabletop

installations, place the unit on a at level surface. Attach the rubber feet to the bottom

of the XGT+ to prevent the unit from sliding. Make sure the unit is placed in a safe, dry

and secure location.

To power the unit using the AC/DC adapter, connect the AC/DC adapter to an AC outlet.

Then connect the barrel plug at the end of the wire on the AC/DC adapter to the 2.5mm

DC barrel connector (center-positive) on the unit. Conrm that the unit has powered up

properly by checking the power status LED located on the front of the unit.

To power the unit using a DC power source, prepare a power cable using a two conductor

insulated wire (not supplied) with a 14 AWG gauge minimum. Cut the power cable to the

length required. Strip approximately 3/8 of an inch of insulation from the power cable

wires. Connect the power cables to the unit by fastening the stripped ends to the DC

power connector.

Connect the power wires to the DC power source. The Power LED should indicate the

presence of power.

WARNING: Note the wire colors used in making the positive and negative connections.

Use the same color assignment for the connection at the DC power source.

NOTE: If mounting with a safety ground attachment, use the safety ground screw at the

rear of the unit.

b. Insert the appropriate 10G SFP+ or XFP transceiver (depending on the model of the

module) into Port 1 receptacle on the XGT+. The release latch of the transceiver must

be in the closed position before insertion.

c. Connect an appropriate multimode or single-mode ber cable to the ber transceiver port

on the XGT+. It is important to ensure that the transmit (Tx) is attached to the receive

side of the device at the other end and the receive (Rx) is attached to the transmit side.

d. When using copper CX4 XFP, connect the cable between the converter and external

device using the recommended copper CX4 cable.

e. Connect the RJ-45 port via a CAT 6A or better cable to a 10GBASE-T Ethernet device.

040-8589N-001B 4/16

Omnitron Systems Technology * 38 Tesla * Irvine, CA 92618

949.250.6510 tel * 949.250.6514 fax * www.omnitron-systems.com

3) VERIFY OPERATION

Once the module has been installed and congured per steps 1 and 2, verify the module is

operational by viewing the LED indicators.

Legend OFF State Color ON/Blinking State

Pwr Off – No power. Green Green – Power On

P1 Lk Off – No Transceiver detected

or no ber link.

Green Green Solid – Fiber link (signal detect).

Amber

Amber Blinking (1Hz) – Port is disabled due to

installed transceiver drawing more current than

allowed.

P1 Stat

Off – Transceiver does not

support digital diagnostic or

no transceiver installed.

Green Green Solid – Transceiver supports digital

diagnostic and no DDMI Alarm Detected.

Amber

Amber Solid – Transceiver supports digital

diagnostic and DDMI alarm detected.

Amber Blinking (1Hz) – Port is disabled due to

installed transceiver drawing more current than

allowed.

P1 LB Off – Port loopback mode not

enabled or congured.

Green

Green Solid – Port set to Loopback mode and port

in loopback.

Green Blinking (1 Hz) – Port responding to BIST

activation with valid BIST response.

Green Blinking (5 Hz) – Port initiating BIST and

receiving valid BIST response.

Amber

Amber Solid – Port set to loopback mode, but XFP

does not support loopback.

Amber Blinking (5 Hz) – Port initiating BIST and not

receiving valid BIST response.

P2 Lk Off – No Transceiver detected

or no ber link.

Green Green Solid – Fiber link

Amber

Amber Blinking (1Hz) – Port is disabled due to

installed transceiver drawing more current than

allowed.

P2 SR Off - Short Reach function is

disabled. Green Green Solid – Short Reach function is enabled.

P2 LB Off – Port loopback mode not

enabled or congured.

Green Green Solid – Port set to Loopback mode and port

in loopback.

Amber Amber Solid – Port set to loopback mode, but

loopback is not supported.

Figure 4: LED Indicators

Otros manuales de Convertidor de medios de Omnitron Systems Technology

Omnitron Systems Technology

Omnitron Systems Technology iConverter GX/T2 Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology miConverter GX/T Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology XM5-1G Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology iConverter GM4-PoE+ Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology iConverter 10/100VT Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology Omnitron iConverter 10/100M2 Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology Omnitron 8000-0 Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology iConverter Gx AN Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology iConverter X21 Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology miConverter 10/100 Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology Omnitron iConverter GX/TM2 Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology miConverter GX/T Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology FlexPoint 100Fx/Tx Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology OmniConverter FPoE/SL Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology Omnitron iConverter 10/100M2 Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology iconverter t3 Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology miConverter 10/100 Plus Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology iConverter 10FL/T Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology iConverter 2GXM2 Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology iConverter 2FXM2 Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology OmniConverter GHPoE/S Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology Plug-in Module iConverter 2FXM Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology iConverter CWDM/X Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology iConverter GX/T2 Manual de usuario

Manuales populares de Convertidor de medios de otras marcas

SoundTraxx

SoundTraxx Blunami BLU-2200 Manual de usuario

SPROLINK

SPROLINK VA1 Manual de usuario

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manual de usuario

Nikon

Nikon AF-S TC-20E III Manual de usuario

Axis

Axis AXIS Q7406 Manual de usuario

Omega

Omega TAC80B-J Manual de usuario

Zoom

Zoom Thunderbolt TAC-2R Manual de usuario

OST

OST iConverter 10/100M Manual de usuario

Vertiv

Vertiv Netsure Manual de usuario

birddog

birddog MINI Manual de usuario

Roland

Roland GI-10 Manual de usuario

Wallenstein

Wallenstein WX310 Manual de usuario

Pace

Pace MSS 200-1 Manual de usuario

Solar Converters

Solar Converters EQ 12/24-50 Manual de usuario

CYP

CYP EL-7400V Manual de usuario

TIE

TIE MIDI 1i1o Manual de usuario

DCS

DCS Vivaldi Upsampler Manual de usuario

Westermo

Westermo MCW-211 SERIES Manual de usuario

Omnitron Systems Technology iConverter XGT+ Manual de usuario

Manuales populares de Convertidor de medios de otras marcas