Omnitron Systems Technology XM5-1G Manual de usuario

iConverter®XM5-1G

Network Interface Device

Quick Start Guide

38 Tesla, Irvine, CA 92618 USA

Phone: (949) 250-6510; Fax: (949) 250-6514

Warning

The operating description in this Instruction Manual is for use by qualied personnel only. To avoid electrical

shock, do not perform any servicing of this module other than that contained in the operating instructions,

unless you are qualied and certied to do so by Omnitron Systems Technology, Inc. (Omnitron)

Caution

Never attempt to open or remove the cover or tamper with the chassis. All user-required operations

can be performed without opening the chassis. There are no user replaceable or serviceable parts in

this unit. Equipment is not intended to be installed and used in a place (home, school, or public area)

accessible to the general population.

Warranty

This product is warranted to the original Buyer against defects in material and workmanship for a period

of TWO YEARS from the date of shipment. By registering this product with Omnitron within 90 days

from the original purchase date the warranty can be extended to THREE YEARS. To register, complete

and mail or fax the enclosed Registration Form. The product can be also registered at www.omnitron-

systems.com. During the in-warranty period, Omnitron will, at its option, repair or replace a product

which is proven to be defective. Repair work performed on an in-warranty product is warranted for the

greater of the remainder of the original warranty period or three (3) months from the date of shipment of

the repaired product from Omnitron. Out-of-warranty repair work is warranted for three (3) months from

the date of shipment of the repaired product and covers exclusively only the actual performed repairs.

For warranty service, the product must be sent to an Omnitron designated facility, at Buyer’s expense.

Omnitron will use its standard shipping method to return the repaired product to Buyer’s designated

Continental United States address.

Limitation of Warranty

The foregoing warranty shall not apply to defects resulting from improper or inadequate use and/

or maintenance of the equipment by Buyer, Buyer-supplied equipment, Buyer-supplied interfacing,

unauthorized modications or tampering with equipment (including removal of equipment cover by

personnel not specically authorized and certied by Omnitron), or misuse, or operating outside the

environmental specication of the product (including but not limited to voltage, ambient temperature,

radiation, unusual dust, etc.), or improper site preparation or maintenance. Software/Firmware

components are provided “as is” and without warranty of any kind. No other warranty is expressed or

implied. Omnitron specically disclaims the implied warranties of merchantability and tness for any

particular purpose.

Exclusive Remedies

The remedies provided herein are the Buyer’s sole and exclusive remedies. Omnitron shall not be liable

for any direct, indirect, special, incidental, or consequential damages of any kind, whether based on

contract, tort, or any legal theory.

General and Copyright Notice

publication may be reproduced, stored in a retrieval system, translated, transcribed, or transmitted, in

any form, or by any means, manual, electric, electronic, electromagnetic, mechanical, chemical, optical

or otherwise, without prior explicit written permission of Omnitron Systems Technology, Inc.

Omnitron Systems Technology, Inc., the Omnitron logo and OST are trademarks of Omnitron Systems

Technology, Inc. iConverter and NetOutlook are registered trademarks of Omnitron Systems Technology,

Inc.

All other trademarks are the property of their respective owners.

Any dispute between a Buyer and Omnitron shall be governed by the laws of the State of California,

U.S.A. without regard to its choice of law principles. Any action brought between a Buyer and Omnitron

may only be brought in the state or federal courts located in the county of Orange in California and each

party consents to the jurisdiction of those courts.

The information contained in this publication is subject to change without notice. Omnitron Systems

Technology, Inc. is not responsible for any inadvertent errors.

Page 2

Page 3

PRODUCT OVERVIEW

This document describes the basic installation and conguration of the XM5-1G Network

Interface Device (NID).

The iConverter XM5-1G is an intelligent Network Interface Device (NID), that delivers

advanced Carrier Ethernet services and provides demarcation at the edges of a network.

The XM5-1G enables rapid service deployments, Service Level Agreement (SLA) assurance

and protection switching.

The SFP ports on the XM5-1G support SERDES 100BASE-X or 1000BASE-X fiber

transceivers and SERDES 1000BASE-T or SGMII 10/100/1000BASE-T copper transceivers.

The SFP interfaces operate in manual mode or auto-negotiation and support full duplex

operation.

The RJ-45 Ethernet ports support 10BASE-T, 100BASE-TX and 1000BASE-T protocols,

auto-negotiation, auto MDI/MDI-X crossover and can be manually forced to a specic speed

and duplex mode using the Command Line Interface.

For more information including the complete User Manual on the XM5-1G models, access

Omnitron’s registration page and register the product:

http://www.omnitron-systems.com/create-an-account.php

INSTALLATION PROCEDURE

1) AC/DC Power Installation

2) Installing SFP Transceivers and Connecting the Cables

3) Congure Module via Command Line Interface

4) Verify Operation

1) AC/DC POWER INSTALLATION

AC Power

To power the XM5-1G using the AC/DC adapter, connect the barrel plug at the end of the wire

on the AC/DC adapter to the 2.5mm DC barrel connector (center-positive) on the back of the

XM5-1G. Then connect the AC/DC adapter to an AC outlet Conrm the XM5-1G has powered

up properly by checking the status of the Power LED located on the front of the XM5-1G.

NOTE: The barrel connector input supports +12VDC only.

Depending on the model number of the module, a second power source is available. Use

the same power supply installation procedure above for the second power supply.

Installation of the equipment should be such that the air ow in the front, back, side and top

vents of the XM5-1G are not compromised or restricted.

If the installation requires grounding, secure the grounding wire to the ground screws. See

the gure on the next page for the location of the grounding screws.

Page 4

Rear View with Dual AC Barrel Connector

NEVER ATTEMPT TO OPEN THE CHASSIS OR SERVICE THE

POWER SUPPLYORFAN MODULE. OPENING THE CHASSIS

MAY CAUSE SERIOUS INJURYOR DEATH.

THERE ARE NO USER REPLACEABLE OR SERVICEABLE

PARTS IN THIS UNIT.

WARNING!!!

DC Power

A power source should be available within 5 ft. of the XM5-1G. The over current protection

for connection with centralized DC shall be provided in the building installation, and shall

be a UL listed circuit breaker rated 20 Amps, and installed per the National Electrical Code,

ANSI/NFPA-70.

The XM5-1G requires +/- 20 to 60VDC (48VDC @ 1.1 Amp max rated power). Appropriate

overloading protection should be provided on the DC power source outlets utilized.

WARNING: OnlyaDC power source that complies with

safety extra low voltage (SELV) requirements can be

connected to the DC-input power supply.

Page 6

NEVER ATTEMPT TO OPEN THE CHASSIS OR SERVICE THE

POWER SUPPLYORFAN MODULE. OPENING THE CHASSIS

MAY CAUSE SERIOUS INJURYOR DEATH.

THERE ARE NO USER REPLACEABLE OR SERVICEABLE

PARTS IN THIS UNIT.

WARNING!!!

2) INSTALLING SFP TRANSCEIVERS AND CONNECTING THE CABLES

The SFP interfaces support SERDES 100BASE-X or 1000BASE-X ber transceivers and

SERDES 1000BASE-T or SGMII 10/100/1000BASE-T copper transceivers.

a. Insert the ber or copper transceivers into the SFP receptacles on the module.

NOTE: The release latch of the transceiver must be in the closed (up) position

before insertion.

The XM5-1G has the ability to detect the speed and automatically congure the port

to match the speed of approved transceivers. Some ber transceivers will need to be

congured using the port CLI commands to congure the speed of the port to match

the speed of the installed SFP transceiver.

b. Connect the appropriate multimode or single-mode ber cable to the ber port of the

installed module. When using dual ber, it is important to ensure that the transmit (TX)

is attached to the receive side of the device at the other end and the receive (RX) is

attached to the transmit side. Single-ber (SF) transceivers operate in pairs. The TX

wavelength must match the RX wavelength at the other end and the RX wavelength

must match the TX wavelength at the other end.

c. For models with xed RJ-45 ports, connect the RJ-45 port via a Category 5 or better

cable to a 10BASE-T, 100BASE-TX or 1000BASE-T Ethernet device (depending on

the conguration of the port).

3) CONFIGURE MODULE via COMMAND LINE INTERFACE

To congure the XM5-1G using the serial port, attach a DB-9 serial (RS-232) equipped

computer with terminal emulation software such as Procomm or Putty to the serial console

port on the XM5-1G using the included cable.

The serial console port is located on the back of the device. Attach the ends of a serial

adapter cable to the serial port of the PC and the RJ-45 connector of the XM5-1G. The port

is a standard RS-232 asynchronous serial interface.

The serial adapter cable pin-outs are illustrated below.

Serial Adapter Cable Pin Outs

WARNING REGARDING EARTHING GROUND:

This equipment shall be connected to the DC supply

system earthing electrode conductor or to a bonding

jumper from an earthing terminal bar or bus to which the

DC supply system earthing electrode is connected.

This equipment shall be located in the same immediate

area (such as adjacent cabinets) as any other equipment

that has a connection between the earthed conductor of

the same DC supply circuit and the earthing conductor,

and also the point of earthing of the DC system. The DC

system shall not be earthed elsewhere.

The DC supply source is to be located within the same

premises as this equipment.

There shall be no switching or disconnecting devices in

the earthed circuit conductor between the DC source and

the earthing electrode conductor.

Locate the DC circuit breaker of the external power source, and switch the circuit breaker

to the OFF position.

Prepare a power cable using a three conductor insulated wire (not supplied) with a 14 AWG

gauge minimum. Cut the power cable to the length required.

Strip approximately 3/8 of an inch of insulation from the power cable wires.

Connect the power cables to the terminal by fastening the stripped ends to the DC power

connector.

WARNING: Note the wire colors used in making the positive, negative and ground

connections. Use the same color assignment for the connection at the circuit breaker.

Connect the power wires to the circuit breaker and switch the circuit breaker ON. The Power

LED will indicate the presence of power.

Installation of the equipment should be such that the air ow in the front, back and side vents

of the XM5-1G are not compromised or restricted.

If the installation requires grounding, secure the grounding wire to the ground screws. See

gure below for the location of the grounding screws.

Rear View with Dual DC Terminal Connector

Page 5

Page 7

Serial Console Port Settings

Start the terminal emulation program and select the correct COM Port. Set the serial port

to the following:

Bits Per Second 115,200 Stop Bits 1

Data Bits 8 Parity NONE

Hardware Flow Control NONE

Once the module has booted, an Entry screen will be displayed on the attached PC. If a

password has been congured, enter the password and press <ENTER>. A system prompt,

‘>’, will be displayed. At the module prompt (>), enter ?, help or h to view the command options.

4) VERIFY OPERATION

Verify the module is operational by viewing the status of the LED indicators. The table below

provides a description for each LED indicator.

The Power LED(s) indicate the module is receiving power from the external power source.

LED Function

“Legend” Color OFF State ON/Blinking State

Power

“Pwr A”

Green/

Yellow No power Solid Green: Module has power

Blinking Yellow (10Hz): Fan Alarm

Power

“Pwr B”

(Dual power models only)

Green/

Yellow No Power Solid Green: Module has power

Blinking Yellow (10Hz): Fan Alarm

P1, P2 Link Activity

“1G” Green Port not linked

at 1G

Solid Green: Port linked at 1G

Blinking Green (10Hz): Data activity

Blinking Green (1Hz): Energy detected but no link

P1, P2 Link Activity

“100” Green Port not linked

at 100M

Solid Green: Port linked at 100M

Blinking Green (10Hz): Data activity

Blinking Green (1Hz): Far-end fault detected but no link

P1, P2 Link Activity

“100” and “1G”

(RJ-45 models only)

Green Port not linked

at 10M

Solid Green: Port linked at 10M

Blinking Green (10Hz): Data activity

P3 - P8 Link Activity

“1G” Green Port not linked

at 1G

Solid Green: Port linked at 1G

Blinking Green (10Hz): Data activity

Blinking Green (1Hz): Energy detected but no link

P3 - P8 Link Activity

“100” Green Port not linked

at 100M

Solid Green: Port linked at 100M

Blinking Green (10Hz): Data activity

Blinking Green (1Hz): Far-end fault detected but no link

P3 - P8 Link Activity

“100” and “1G”

(RJ-45 models only)

Green Port not linked

at 10M

Solid Green: Port linked at 10M

Blinking Green (10Hz): Data activity

Mgmt

“1G”

(Located on the back)

Green Port not linked

at 1G

Solid Green: Port linked at 1G

Blinking Green (10Hz): Data activity

Blinking Green (1Hz): Auto-negotiation detected but no

link

Mgmt

“100”

(Located on the back)

Green Port not linked

at 100M

Solid Green: Port linked at 100M

Blinking Green (10Hz): Data activity

Blinking Green (1Hz): Far-end fault detected but no link

Mgmt

“100” and “1G”

(Located on the back)

Green Port not linked

at 10M

Solid Green: Port linked at 10M

Blinking Green (10Hz): Data activity

LED Indicators

NOTE: LED indicators will vary depending on the model.

Page 8

Specications

Description iConverter XM5-1G

1G Network Interface Device

Standard

Compliances

IEEE 802.1Q, 802.1ad, 802.1p, 802.3, 802.3ah, 802.1ag, 1588v2

RFC 2819 (RMON), 2863 (IF-MIB), 2131 (DHCP), 2544, 5357, 4541

ITU-T G.8031, G.8032, G.8262, Y.1731, Y.1564

MEF Carrier Ethernet 2.0 Certied

MEF 6.2, 9, 10.2, 14, 21, 26.1, 30, 31, 33

Management Telnet, SNMPv1, SNMPv2c, SNMPv3, SSH, Serial Console

Regulatory

Compliances* UL, CE, FCC Class A, NEBS Level 3, RoHS2 (6/6), WEEE, REACH

Frame Size Up to 10,056 bytes

Port Types

Copper: 10/100/1000BASE-T

(RJ-45)

Fiber: 1000BASE-X

100BASE-X

Serial:

(Management)

RS-232 (RJ-45)

Copper:

(Management)

10/100/1000BASE-T (RJ-45)

Cable Types

Copper: EIA/TIA 568 A/B, Category 5 and higher

Fiber: Multimode: 50/125um, 62.5/125um

Single-mode: 9/125um

Serial:

(Management)

EIA/TIA 568 A/B, Category 3 and

higher

Copper:

(Management) EIA/TIA 568 A/B, Category 5 and higher

AC Power

Requirements AC Power Adapter: 100-240VAC~ 50-60Hz

0.3A @ 110VAC

DC Power

Requirements

2.5mm Barrel

Connector:

12VDC

Maximum power consumption 30W

3-Pin Terminal: +/- 20VDC to 60VDC

Maximum power consumption 30W

Temperature

Commercial:

Wide:

Extended:

Storage:

0 to 50° C

-40 to 60° C

-40 to 75° C

-40 to 80° C

Dimensions W: 7.29” x D: 9.15” x H: 1.63”

L: 185.17mm x B: 232.41mm x H: 41.4mm

Weight 3.24 lbs (1.47 kg)

Humidity 5% to 95% (non-condensing)

Altitude -100m to 4,000m (operational)

Technical Support 24/7/365 free Technical Support during warranty

Warranty 2 years standard; 3 years with registration

*Pending

040-09640-001A 3/17

Tabla de contenidos

Otros manuales de Convertidor de medios de Omnitron Systems Technology

Omnitron Systems Technology

Omnitron Systems Technology Omnitron iConverter 10/100M2 Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology miConverter Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology iConverter 10/100VT Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology 10/100 Media Converter miConverter Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology OmniRepeater 400 Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology FlexPoint 100Fx/Tx Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology iConverter 2FXM2 Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology Omnitron iConverter 10/100M2 Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology miConverter 10/100 Plus Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology iConverter Gx AN Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology iConverter GM4-PoE+ Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology iConverter 100Tx Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology iConverter X21 Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology miConverter GX/T Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology Fiber-to-Fiber Converter 1000FF Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology Serial RS-422 and RS-485 to Fiber Media Converter... Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology iConverter Gx AN Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology E1 Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology OmniConverter GPoE+/SX Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology OmniConverter GPoE+/S Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology miConverter 10/100 Plus Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology Omnitron iConverter 10/100M Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology OmniConverter FPoE/SL Manual de usuario

Omnitron Systems Technology

Omnitron Systems Technology iConverter GX/T2 Manual de usuario

Manuales populares de Convertidor de medios de otras marcas

SoundTraxx

SoundTraxx Blunami BLU-2200 Manual de usuario

SPROLINK

SPROLINK VA1 Manual de usuario

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manual de usuario

Nikon

Nikon AF-S TC-20E III Manual de usuario

Axis

Axis AXIS Q7406 Manual de usuario

Omega

Omega TAC80B-J Manual de usuario

Zoom

Zoom Thunderbolt TAC-2R Manual de usuario

OST

OST iConverter 10/100M Manual de usuario

Vertiv

Vertiv Netsure Manual de usuario

birddog

birddog MINI Manual de usuario

Roland

Roland GI-10 Manual de usuario

Wallenstein

Wallenstein WX310 Manual de usuario

Pace

Pace MSS 200-1 Manual de usuario

Solar Converters

Solar Converters EQ 12/24-50 Manual de usuario

CYP

CYP EL-7400V Manual de usuario

TIE

TIE MIDI 1i1o Manual de usuario

DCS

DCS Vivaldi Upsampler Manual de usuario

Westermo

Westermo MCW-211 SERIES Manual de usuario