Olympus SZX-DA Manual de usuario
INSTRUCTIONS
SZX-DA
DRAWING ATTACHMENT
This instruction manual is for the Olympus SZX-DA drawing attachment. To ensure the safety,
obtain optimum performance and familiarize yourself fully with the use of this product, we
recommend you study this manual thoroughly before operating the equipment. Retain this
instruction manual in an easily accessible place near the work desk for future reference.
A X 7 1 8 9
i
IMPORTANT
1Getting Ready
1. This manual describes the SZX-DA drawing attachment only. Before using this equipment with the SZX microscope and
associated options, make sure that you have carefully read and understood the corresponding manuals, and understand
how to use all components of the microscopic system in combination.
2. This attachment is a precision instrument. Handle it with care and avoid subjecting it to sudden or severe impact.
3. Do not use the attachment anywhere where it may be subjected to direct sunlight, high temperature and humidity, dust or
vibrations.
2Maintenance and Storage
1. Clean all glass components by wiping gently with gauze. To remove fingerprints or oil smudges, wipe with gauze slightly
moistened with a mixture of ether (70%) and alcohol (30%).
Since solvents such as ether and alcohol are highly flammable, they must be handled carefully. Be sure to keep
these chemicals away from open flames or potential sources of electrical sparks —— for example, electrical equipment
that is being switched on or off. Also remember to always use these chemicals only in a well-ventilated room.
2. Do not use organic solvents to clean non-optical components. If smudges are difficult to clean, wipe them with a soft cloth
slightly moistened with a diluted neutral detergent.
3. Never disassemble any part of the unit as this could cause malfunctions or reduced performance.
ii
3Caution
If the equipment is used in a manner not specified by this manual, the safety of the user may be imperiled. In addition, the
equipment may also be damaged. Always operate the equipment as outlined in this instruction manual.
The following symbols are used to set off text in this instruction manual.
: Indicates that failure to follow the instructions in the warning could result in bodily harm to the
user and/or damage to equipment (including objects in the vicinity of the equipment).
# : Indicates that failure to follow the instructions could result in damage to equipment.
} : Indicates commentary (for ease of operation and maintenance).
CONTENTS
1NOMENCLATURE
2ASSEMBLY
3DRAWING/OBSERVATION SETUP
4OBSERVATION PROCEDURE
5DRAWING MAGNIFICATION
6SPECIFICATIONS
1
2
3
4
6
7
SZX-DA
1
NOMENCLATURE
Positioning pin
Mirror tube clamping knob
Clamping screw
Mirror tube
Light shield cap
Focusing handle
SZX-DA
2
ASSEMBLY
The diagram below shows how to connect this attachment to the microscopic system. The numbers in the diagram indicate
the order of assembly.
# When assembling the microscopic system, make sure that all parts are free of dust and dirt. Avoid scratching any
parts or touching the glass surfaces.
Positioning groove
Allen screwdriver
(Provided with the
SZX microscope body)
Required Tool
}The attachment can be mounted so that it is
located either on the left or right side of the zoom
microscope body.
Positioning pin
Positioning pin
Clamping screw
Observation tube
Drawing
attachment
SZX zoom microscope body
Clamping screw
Positioning groove
Mirror tube
1
2
3
DRAWING/OBSERVATION SETUP
SZX
SZX-DA
Focusing handle
Adjusts the focusing of the
drawing sheet.
Mirror tube clamping knob
Clamps the mirror tube after
it has been pivoted to the de-
sired position.
Mirror tube
Light shield cap
Shields the light on the
drawing side.
Drawing sheet
SZX-DA
4
OBSERVATION PROCEDURE
Mirror tube
Fig. 1
1Placing the Drawing Sheet
Place a drawing sheet directly below the mirror tube and fix so that it does
not move.
2Adjusting the Mirror Tube (Fig. 1)
Loosen the mirror tube clamping knob @, pivot the mirror tube so that it is
perpendicular to the drawing sheet. Then tighten the mirror tube clamping
knob @.
#If the mirror pivoting angle is too large, drawing will be difficult be-
cause the pen motion on the drawing sheet will not coincide with
that in the field of view.
3Focusing the Specimen
Focus the specimen using the coarse or fine focus adjustment knob on
the microscope body.
Drawing
sheet
@
5
4Removing the Light Shield Cap (Fig. 2)
The light shield cap should be removed and placed on the top of the
mirror tube during drawing.
#When microscopic observation is required while the drawing attach-
ment is mounted on the microscope, attach the light shield cap on
the drawing sheet side to shield the light.
Mirror tube
Fig. 2
5Focusing the Drawing Sheet
Turn the focusing handle to bring the drawing sheet into focus.
6Adjusting the Brightness Balance Between the
Drawing Image and Specimen Image
Look into the observation tube eyepieces, place the tip of a pen or similar
thin object on the drawing sheet and adjust the microscope illumination
so that both the pen tip and specimen are clearly visible.
#If the drawing sheet surface looks dark, illuminate it with a desk lamp
or place the sheet on a light box.
7Drawing
Look into the observation tube eyepieces and trace the specimen image
on the drawing sheet using a pencil or similar writing tool.
SZX-DA
6
DRAWING MAGNIFICATION
Use the following procedure and formula to calculate the drawing magni-
fication.
1Measuring Drawing Size D(Figs. 3 & 4)
Place the scale line on the drawing sheet, look into the eyepiece and read
the size of the drawing field, D.
2Calculating Drawing Magnification ß
* The field number is indicated on the eyepiece.
(Example) With indication WHS10X22, “22” is the field number.
ß=Drawing size D
Eyepiece field number * x
Total magnification reading
on the zooming knob
10
Fig. 3
D
D
Fig. 4
(Scale reading)
Eyepiece field of view
(Drawing field of view)
Tabla de contenidos
Otros manuales de Microscopio de Olympus
Olympus
Olympus SZ-III Manual de usuario
Olympus
Olympus CHBS Manual de usuario
Olympus
Olympus FLUOVIEW FV300 Manual de usuario
Olympus
Olympus BH2 Series Guía
Olympus
Olympus DP21-SAL Guía del usuario
Olympus
Olympus CX31 Manual de usuario
Olympus
Olympus BHT Manual de usuario
Olympus
Olympus CX31 Manual de usuario
Olympus
Olympus CHD Manual de usuario
Olympus
Olympus K Instrucciones de funcionamiento
Olympus
Olympus SZX7 Manual de usuario
Olympus
Olympus IX71 Manual de usuario
Olympus
Olympus U-UVF248A Manual de usuario
Olympus
Olympus BH2 Series Manual de usuario
Olympus
Olympus Discover FV10i Manual del propietario
Olympus
Olympus U-CBE Manual de usuario
Olympus
Olympus U-D5BDREMC-VA3 Instrucciones de funcionamiento
Olympus
Olympus BH2 Series Instrucciones de funcionamiento
Olympus
Olympus Pom Manual de usuario
Olympus
Olympus FV3000 Manual de usuario
