OHAUS Traveler Series Manual de usuario
Quick Start Guide Traveler
Scales
Ohaus Corporation www.ohaus.com iTravelerScales Quick Start Guide
PREPARATION FOR USE
Install Pan, Release Locks
Install the metal pan over the sub-platform.
Before using the scale, release the
Transportation Lock. On scale bottom,
slide the locking pin to the position.
Calibration Lock: to change, see Instruction
Manual. (Otherwise leave as is.)
Check Power
Be sure local line voltage matches voltage
printed on the scale’s power adapter. If not,
contact an Ohaus dealer.
To use battery power, remove battery cover
and insert LR6 (AA) batteries.
SELECTING THE LOCATION:
Place on a firm, steady surface. Avoid locations with excessive air current, vibrations,
heat sources, or rapid temperature changes. Place with sufficient space on all sides.
SAFETY PRECAUTIONS
For safe and dependable operation of this product, please comply with the following
safety precautions:
•Verify that the input voltage printed on the power Adapter and the plug type matches
the local power supply.
•Make sure that the power cord does not pose an obstacle or tripping hazard.
•Disconnect the product from the power supply when cleaning.
•Do not operate this product in hazardous or unstable environments.
•Do not drop loads on the pan.
•Use only approved accessories and peripherals, as available.
•Operate the product only under ambient conditions specified in the Instruction Manual.
•Service should be performed by authorized personnel only.
Transportation
Lock
Power Input Jack
Remove
Battery
Cover to
insert
Batteries:
LR6 (AA).
Calibration
Lock
Communication
Interface
compartment
(See page 3.)
Quick_Start_Guide_Traveler_V1
Traveler
Scales Quick Start Guide
Traveler
Scales Quick Start Guide ii Ohaus Corporation www.ohaus.com
CONTROLS
Key Name Function
Primary function (Short Press) – If scale is Off, turn On.
If scale is on, perform Zero/Tare.
Secondary function (Long Press) – Turn scale Off.
On-Zero
Off
Yes
Menu function – (Yes) Use this key to accept the currently
displayed setting.
Primary function (Short Press) – Send the current display
value to serial port if installed.
Print
Cal Secondary function (Long Press) – Starts Span Calibration
as available in menu.
Primary function (Short Press) – Advances to next available
unit.
Unit
No Menu function – (No) Use this key to reject the displayed
setting and advance to next available setting.
Symbols for weighing units.
(Only g– Grams, and
N
–
Newtons are available.)
Battery usage
indicator
Stability
indicator
Center of Zero
indicator
Quick Start Guide Traveler
Scales
Ohaus Corporation www.ohaus.com iii Traveler
Scales Quick Start Guide
OPERATION
POWER On/Off: With scale off, press ON. The scale performs a display test,
then displays zero. With scale on, press and hold Off until OFF is displayed.
Remove load from pan and press ZERO to set display to zero.
Manual Tare: Place an empty container on the pan and press ZERO.
The display reverts to 0. Place material to be weighed in the container.
The net weight is displayed.
To clear Tare value, remove container and press ZERO.
ADDITIONAL OPERATIONS
Changing Unit of Measure:
First make units available in Setup/Units menu.
(See Menu Navigation and Menu Structure, next page.)
Press Unit to advance to next available weighing Unit.
For more menu operations, see next page. For calibration, see the Calibration Guide.
DRAFT SHIELD
The draft shield has a center piece which can be removed and
used as a sample tray. Rotate counter-clockwise to remove
the center piece. (The draft shield can be used with or without the
center piece.)
COMMUNICATION OPTIONS
RS232 or USB interface kits are available as optional accessories.
RS232 Interface Kit:
USB Interface Kit:
Traveler
Scales Quick Start Guide
Traveler
Scales Quick Start Guide iv Ohaus Corporation www.ohaus.com
MENU NAVIGATION
Main level menus are identified by decimal points between each letter, for example S.E.t.U.P.
Enter Menu:
With the scale off, press and hold the On button.
Continue holding the On button until S.E.t.U.P appears.
Press Yes to enter each main menu.
Press No to advance to the next main menu.
Change Settings:
Within each main menu are sub-menus.
Press Yes to enter each sub-menu.
Press No to advance to the next sub-menu.
Press Yes to accept the displayed sub-menu setting.
Press No to advance to the next setting.
Menu Exit:
The last item in each sub-menu is EnD.
Press Yes to return to the main menu.
Press No to return to the first sub-menu.
The last item in the main menu is E.n.D. Press Yes to return to the previous weighing mode.
MENU STRUCTURE
S.e.t.u.p
S.e.t.u.pS.e.t.u.p
S.e.t.u.p
A-Off On
OFF
SpaN
Yes / No
Lin
Yes / No
End
Yes / No
U.n.i.t
U.n.i.tU.n.i.t
U.n.i.t
g
On
OnOn
On
/
Off
OffOff
Off
N
On
On On
On
/
Off
Off Off
Off
End
Yes / No
P.r.i.n.t*
Stable
APrint
End
r.S.2.3.2*
On-OFF
BaUd
Parity
Hands
End
U.S.B*
On-OFF
BaUd
Parity
Hands
End
E.n.d
E.n.dE.n.d
E.n.d
Yes / No
*Print, RS232, and USB menus are only seen after the corresponding interface is installed.
*80253046*
P/N 80253046
Tabla de contenidos
Otros manuales de Escala de OHAUS
OHAUS
OHAUS EXPLORER Manual de usuario
OHAUS
OHAUS Ranger 3000 Series Manual de usuario
OHAUS
OHAUS i-D33P75SD Manual de usuario
OHAUS
OHAUS Ranger Manual de usuario
OHAUS
OHAUS CHAMP II BASE Manual de usuario
OHAUS
OHAUS VE Series Manual de usuario
OHAUS
OHAUS Scout STX Manual de funcionamiento
OHAUS
OHAUS 1600 Series Manual de usuario
OHAUS
OHAUS Aviator 2000 Series Manual de usuario
OHAUS
OHAUS SKIPPER 6000 Guía rápida
OHAUS
OHAUS Dial-O-Gram Manual de usuario
OHAUS
OHAUS SJX1502N/E Manual de funcionamiento
OHAUS
OHAUS Adventurer AX224N Manual de usuario
OHAUS
OHAUS Harvard Trip 1450-SD Manual de usuario
OHAUS
OHAUS Navigator Series Manual de usuario
OHAUS
OHAUS Valor 2000W Series Manual de usuario
OHAUS
OHAUS SCOUT II Manual de usuario
OHAUS
OHAUS Scout SPX Series Manual de usuario
OHAUS
OHAUS Adventurer AX124/E Manual de usuario
OHAUS
OHAUS Explorer EX1241 Manual de usuario
