OHAUS Explorer E1F110 Manual de usuario

Tabla de contenidos

Otros manuales de Escala de OHAUS

OHAUS

OHAUS FD Series Manual de usuario

OHAUS

OHAUS Defender D30BR Manual de usuario

OHAUS

OHAUS CKW3R Manual de usuario

OHAUS

OHAUS Defender 2200 Manual de usuario

OHAUS

OHAUS Ranger Manual de usuario

OHAUS

OHAUS FD3 Manual de usuario

OHAUS

OHAUS Valor 1000 Manual de usuario

OHAUS

OHAUS Defender 3000 Series Manual de usuario

OHAUS

OHAUS AV53 Manual de usuario

OHAUS

OHAUS Ranger Manual de usuario

OHAUS

OHAUS PJX Series Manual de usuario

OHAUS

OHAUS Voyager Balances Manual de usuario

OHAUS

OHAUS SD35 Manual de usuario

OHAUS

OHAUS CD-11 Manual de usuario

OHAUS

OHAUS Adventurer SL AS64 Manual de usuario

OHAUS

OHAUS valor 5000 series Manual de usuario

OHAUS

OHAUS BW1.5 Manual de usuario

OHAUS

OHAUS 1119-DO Manual de usuario

OHAUS

OHAUS Defender 3000 Series Manual de usuario

OHAUS

OHAUS Scout pro Manual de usuario

OHAUS

OHAUS RS Series Manual de usuario

OHAUS

OHAUS TROOPER COUNT Manual de usuario

OHAUS

OHAUS AS20 Manual de usuario

OHAUS

OHAUS Adventurer AX224N Manual de usuario

Manuales populares de Escala de otras marcas

AWS

AWS ZEO-50 Manual de usuario

Gima

Gima Glass Body Fat Analyzer Manual de lista de piezas

Seca

Seca 374 Manual de usuario

TEC

TEC TEC SL59 SERIES Manual de usuario

Axis

Axis B/E Series Manual de usuario

Alecto

Alecto ACW-40 Manual de usuario

Rice Lake

Rice Lake MSI-4260 IS Manual de usuario

IKA

IKA RCT basic safety control Manual de usuario

ADE

ADE M20011 Manual de usuario

Duronic

Duronic KS3000 Manual de usuario

Digi

Digi SM-720 Manual de usuario

Cardinal

Cardinal CS Series Manual de usuario

Korona

Korona Kastella Manual de usuario

A&D

A&D FC-50Ki Manual de usuario

BDA

BDA CAMARGUE Manual de usuario

Tanita

Tanita HD-357 Manual de usuario

Leifheit

Leifheit 03173 Manual de usuario

Lumme

Lumme LU-1340 Manual de usuario

Ohaus Explorer

Manufacturer: Ohaus

Product Range: Explorer

Model Tested: E1F110

Capacity - 6100g

Readability - 0.1g

Note:

The Explorer normally comes with an RS232 serial interface fitted as standard, please check with your balance supplier

that this is the case.

Setting up the balance:

• Getting into RS232 Mode

Turn the unit on.

Press the “Setup” button.

Press the “right” button until “RS232” is displayed then press the “Enter” button.

• Setting the Baud rate to 1200.

“BAUD” should now be displayed, press the “Enter” button.

Press the up or down buttons until “1200” is displayed then press the “Enter” button.

• Setting the Parity to none.

“PARITY” should now be displayed, press the “Enter” button.

Press the up or down buttons until “nonE” is displayed then press the “Enter” button.

• Setting the Data to 7 bits.

“DATA” should now be displayed, press the “Enter” button.

Press the up or down buttons until “7” is displayed then press the “Enter” button.

• Setting the Stop bits to 2.

“STOP” should now be displayed, press the “Enter” button.

Press the up or down buttons until “2” is displayed then press the “Enter” button.

• Setting Lock to Off.

“LOCK” should now be displayed, press the “Enter” button.

Press the up or down buttons until “OFF” is displayed then press the “Enter” button.

• Returning to normal operation.

“EXIT” should now be displayed, press the “Enter” button.

Serial Balance Adapter Data Sheet OH-2

© DCP Microdevelopments Ltd www.dcpmicro.com [email protected] 12/12/00

Setting up the balance (continued):

• Getting into Print setup mode.

Press the “Setup” button.

Press the “right” button until “PRINT” is displayed then press the “Enter” button.

• Setting the balance to autoprint.

“AUTOPRT” should now be displayed, press the “Enter” button.

Press the up or down buttons until “CONT” is displayed then press the “Enter” button.

• Returning to normal operation.

Press the left or right buttons until “Exit” is displayed, press the “Enter” button.

The balance is now set up to work with the LogIT Serial Balance Adapter - See Connecting the Balance for details of the

lead required to connect the balance to the LogIT Adapter.

Connecting the balance:

A cable must be made to connect the balance serial port to the LogIT Serial Adapter using the wiring information below.

Explorer RS232 port, 9 way D Socket Balance Adapter, 9 Way D Socket

pin 2 pin 2

pin 5

pin 6

pin 7 pin 5

Note: These connection instructions are designed for use with the 9 pin boxed version of the LogIT Serial Balance

Adapter. If using the original 25 pin lead type connection you need to use adapter pin 3 instead of pin 2 (data out) and

adapter pin 7 instead of pin 5 (ground).

Serial Balance Adapter Data Sheet OH-2

© DCP Microdevelopments Ltd www.dcpmicro.com [email protected] 12/12/00

Connect balance pin 5 to pin 6 to bypass handshaking