OHAUS I-DT33P Manual de usuario

i-DT33P / i-DT33XW Indicator

Ethernet Option

Instruction Manual

EN-1

INTRODUCTION

This Ethernet interface kit is for use with the Defender®3000 i-DT33P and i-

DT33XW indicators.

KIT CONTENTS

Cable

Screws(3)

Ethernet

Cable

Ethernet

PC

Board

Watertight

Seal (with

One or Two

Holes)

CAUTION: THE INSTALLATION AND CONNECTIONS SHOULD

ONLY BE PERFORMED BY AUTHORIZED AND QUALIFIED

PERSONNEL, SUCH AS AN ELECTRICIAN.

EN-2

INTERFACE INSTALLATION

Install the Ethernet Interface kit to the indicator as the following.

WARNING: BEFORE INSTALLATION, POWER OFF THE

INDICATOR AND REMOVE ALL EXTERNAL AC POWER

CONNECTIONS.

i-DT33P

1. Remove the battery cover in the direction of the arrow, and take out dry

batteries if used.

2. Slightly push the end of the charging cover (circled) in the direction of the

arrow and take it out.

EN-3

3. Remove the Ethernet sealing plug upwards.

4. Take out the cable supplied. Connect one side to the main board connector

(circled), and pass the other side through the side hole.

EN-4

5. Take out the Ethernet PC board supplied. Connect the cable's another side to

the connector on the Ethernet board (circled). Then insert the Ethernet board

into the two card slots (circled) on both sides.

6. Take out the Ethernet cable supplied, and pass it through the hole where the

sealing plug is removed, and then connect the Ethernet interface to the

connector on the Ethernet board (circled).

Ethernet PC board

EN-5

7. Re-install the dry batteries if used and close the battery cover to finish

installation.

i-DT33XW

1. Remove the six hex head bolts from the rear housing of the indicator.

EN-6

2. Release the strain relief for option connector (circled) including the watertight

seal in it on the bottom of the indicator and remove the plug at the end of it.

3. Take out the cable and the Ethernet PC board supplied. Connect one side of

the cable to the connector on the Ethernet PC board (circled) and the other to

the indicator's main board connector (circled).

Watertight Seal （with One Hole）

Plug

EN-7

4. Pin the upper right corner of the Ethernet PC board on the positioning column

(circled). Make sure the back of the Ethernet PC board is facing up.

5. Screw the two screws (circled) on the Ethernet PC board to the indicator.

Pass the Ethernet cable through the strain relief for option connector and

attach the watertight seal to it, and then connect the Ethernet interface to the

connector on the Ethernet board (circled).

EN-8

Note: If you install RS232 and the Ethernet kit at the same time, please use the

supplied watertight seal with two holes. Make sure to install the RS232 cable first

before the connection of Ethernet kit. Pass the RS232 cable through one hole of

the watertight seal and the Ethernet cable through another.

Watertight Seal （with Two Holes）

Otros manuales para i-DT33P

2

Este manual sirve para los siguientes modelos

1

Tabla de contenidos

Otros manuales de Instrumento de medición de OHAUS

OHAUS

OHAUS D52 Manual de usuario

OHAUS

OHAUS MB45 Manual de usuario

OHAUS

OHAUS ST300 Manual de usuario

OHAUS

OHAUS CKW Series Manual de usuario

OHAUS

OHAUS MB90 Manual de usuario

OHAUS

OHAUS STARTER 300 Manual de usuario

OHAUS

OHAUS MB90 Manual de usuario

OHAUS

OHAUS STARTER 300D Manual de usuario

OHAUS

OHAUS ST Series Manual de usuario

OHAUS

OHAUS a-AB33M1 Manual de usuario

OHAUS

OHAUS CKW-55 Manual de usuario

OHAUS

OHAUS Ranger 3000 Series Manual de usuario

OHAUS

OHAUS a-AB33M1 Manual de usuario

OHAUS

OHAUS a-AB33M1 Manual de usuario

OHAUS

OHAUS ST300-B Manual de usuario

OHAUS

OHAUS TD52P Manual de usuario

OHAUS

OHAUS STARTER 2100 Manual de usuario

OHAUS

OHAUS CKW Manual de uso y cuidado

OHAUS

OHAUS STARTER 2100 Manual de usuario

OHAUS

OHAUS MB35 Manual de usuario

OHAUS

OHAUS STARTER 400D Manual de usuario

OHAUS

OHAUS ST20C-A Manual de usuario

OHAUS

OHAUS Defender 3000 Manual de usuario

OHAUS

OHAUS a-AB23EC Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario