OHAUS D52 Manual de usuario

D52 Indicator

RS232/RS485/USB Option

Instruction Manual

Interfaz RS232/RS485/USB

Manual de instrucciones

Interface RS232/RS485/USB

Manuel d’instruction

RS232/RS485/USB Schnittstelle

Bedienungsanleitung

Interfaccia USB/RS232/RS485

Manuale di Istruzioni

USB/RS232/RS485 折

折ↅ

∎䞷広㢝󱂖

EN-1

INTRODUCTION

This RS232/RS485/USB interface kit is for use with the Defender®5000 TD52 indicators

and D52 scales.

KIT CONTENT

INTERFACE INSTALLATION

Install the RS232 / RS485 / USB Device Interface on the underside of the indicator as

shown.

For TD52P:

1. Separate the terminal from the base by loosening load cell cable male connector.

Remove the interface option cover.

Load cell cable male connector

Interface option cover

EN-2

2. Break off the rib of the interface option cover as shown.

3. Connect the cable to the main board connector as shown. Place the ferrite in the

groove of the rear housing.

4. Install the RS232/RS485/USB Device board. Secure it with the 2 screws.

Connect the cable to the accessory board 12 pin connector.

Rib

Ferrite

Main board

connector 2

Cable

12 Pin Connector

Screw

EN-3

5. Set the function switch to according to the desired function.

Connect the corresponding RS232, RS485 or USB device cable to the applicable

connector.

Refer to Table 1 in the Setup section for the function switch settings.

Refer to Table 2 in the Setup section for RS232RS485 connection for external

serial devices.

6. Fix the output cable with the nylon cable tie.

7. Put the interface option cover back on the terminal.

Function switch

USB Device Socket

RS232/RS485 Connector

Nylon cable tie

Output cable

EN-4

For TD52XW:

1. Separate the terminal from the base by loosening load cell cable female

connector. Remove the interface option cover.

2. Take the rear housing down from the front housing as shown.

screws

Load cell cable male

connector

M25 hole plug

EN-5

3. Connect the cable to the main board connector. Place the ferrite in the slot of the

internal cover as shown.

4. Install the RS232 / RS 485 / USB device board. Secure it with 2 screws

(Note: boss post is 5 and 7). Connect the cable to RS232 / 485 / USB device

board 12 pin connectors.

Cable

Ferrite

Main board connector 2

Boss Post 5, 7

EN-6

5. Pass the RS232 / RS485 / USB device output cable through the cap nut; then

spread the rubber seal and place it over the cable. Now pass the cable through

the body of the cable gland.

12Pin Connector

Function switch

RS232/RS485

connector

screw

RS232 / RS485

Output

M25 Cable Gland

Cap nut

USB Device

Output Cable

M25 Cable Gland

Cap nut

EN-7

6. Toggle the Function switch according to different function. Put the corresponding

RS232 cable, RS485 cable or USB Device cable through the M25 hole. Connect

it to the applicable connectors.

7. Put the rear housing back on the front housing. Re-install the 6 screws.

8. Fasten the M25 gland to the rear housing.

RS232 cable / RS485 cable

USB Device cable

Current loop cable

M25 gland

EN-8

9. Push the rubber seal into the M25 cable gland.

10. Fasten the cap nut of the M25 gland.

For TD52XW with reversed rear cover:

1. Separate the terminal from the base by loosening load cell cable female

connector. Remove the interface option cover.

Rubber seal

Cap nut of M25 gland

Screw

M25 hole plug

Load cell cable male connector

Tabla de contenidos

Idiomas:

Otros manuales de Instrumento de medición de OHAUS

OHAUS

OHAUS MC2000 Manual de usuario

OHAUS

OHAUS TD52P Manual de usuario

OHAUS

OHAUS ST300-B Manual de usuario

OHAUS

OHAUS i-DT33P Manual de usuario

OHAUS

OHAUS STARTER 300D Manual de usuario

OHAUS

OHAUS STARTER 3100M Manual de usuario

OHAUS

OHAUS ST300 Manual de usuario

OHAUS

OHAUS STARTER 2100 Manual de usuario

OHAUS

OHAUS ST20C-A Manual de usuario

OHAUS

OHAUS STARTER 5000 Manual de usuario

OHAUS

OHAUS i-DT33P Manual de usuario

OHAUS

OHAUS ST400 Manual de usuario

OHAUS

OHAUS CD-1 Manual de usuario

OHAUS

OHAUS starter 3100 Manual de usuario

OHAUS

OHAUS T51XW Manual de usuario

OHAUS

OHAUS STARTER 300 Manual de usuario

OHAUS

OHAUS a-AB33M1 Manual de usuario

OHAUS

OHAUS MB45 Manual de usuario

OHAUS

OHAUS MB45 Manual de usuario

OHAUS

OHAUS STARTER 3100C Manual de usuario

OHAUS

OHAUS CKW-55 Manual de usuario

OHAUS

OHAUS MB95 Manual de usuario

OHAUS

OHAUS Defender 3000 Manual de usuario

OHAUS

OHAUS ST300-G Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario