Oasis Builder Series Manual de usuario

These guidelines are recommended for

the proper installation of Oasis products. A

careful review of these procedures (and any

referenced publications) before starting is

important in avoiding an improper assembly

and/or installation.

NOTE: All illustrations in this publication are

typical, and may appear different than the

actual product. Optional items may also be

shown that were not ordered on the product

being installed.

ON WHIRLPOOL EQUIPPED MODELS, A

SEPARATE SET OF INSTRUCTIONS

IS PACKED WITH THE UNIT

FOR THE WHIRLPOOL SYSTEM.

READ THEM BEFORE INSTALLING UNIT!

Special Notes to Installer

uLIFT UNIT ONLY BY THE OUTSIDE

SHELL. DO NOT HANDLE BY SYSTEM

PIPING OR COMPONENTS!

uIt is the sole responsibility of the installer

to determine the requirements necessary for

compliance with all code requirements!

uAll paperwork packaged with the product

should be saved and presented to the home

owner upon completion of the installation!

uAll published product dimensions are

for reference only. Any critical dimensions

required for installation should be taken

directly from the product being installed!

u Anyindependentmodicationsmadeto

the product (or any options / accessories

supplied) beyond those required for normal

installation can void all warranties! (Refer to

warranties for further information)

INSPECTION GUIDELINES

Carefully check the unit upon receipt. Notify

your supplier immediately if any questions

or problems are encountered during this

process.

DO NOT INSTALL PRODUCT

WITHOUT FIRST ADDRESSING

QUESTIONS WHICH ARISE DURING

THE INSPECTION!

Basic Module Check

lCheck unit drain position for match to

bathroom drain location.

lCheck unit for surface damage.

lCheck unit color for coordination to other

bathroomxtures.

Whirlpool System Check

Assembly and operational instructions are

included in a separate publication for all

whirlpool and air equipped models.

lCheck for proper trim color and system

options.

INSTALLATION SITE FRAMING

WARNING!

Oasis self-rimming models ARE NOT

designed for insertion into a

pre-nished deck or platform.

Any unit or system damage resulting

from the ‘drop-in’ installation technique

may void all warranties.

When the installation involves a deck or

platformarea,framingand/ornishingthe

deck or platform is NOT RECOMMENDED

until the unit has been secured in position.

NOTE: A pump access MUST BE

PROVIDED for all whirlpool equipped units.

Additional access may be required to

comply with local codes.

NOTE: ‘Wet-set’ is not required to support

theoorunderanOasisproductduetothe

encapsulated Balsa wood construction.

Self-Rimming Installations - Builder Series

Paradise Isle TR-B-900 Andros Isle TR-B-400

Geneva 3260 TR-B-200/TRG-200 Geneva 3672 TR-B-270/TRG-270

Geneva 3660 TR-B-240/TRG-240 Vincennes 2 / HGG-490

San Salvador 1 TR-B-100 Classic 4060 OV-B-340/OVG-340

San Salvador 2 TR-B-150 Futura 4260 OV-B-310/OVG-310

Prestige 3466 TR-B-220 Classic 4472 OV-B-380

Prestige 4272 TR-B-140 Futura 4272 OV-B-320/OVG-320

Prestige 4872 TR-B-850

Paradise Isle / TR-B-900

Andros Isle / TR-B-400

Geneva 3260 / TR-B-200, TRG-200

Geneva 3660 / TR-B-240, TRG-240

Geneva 3672 / TR-B-270, TRG-270

San Salvador 1 / TR-B-100

San Salvador 2 / TR-B-150

Prestige 3466 / TR-B-220

Prestige 4272 / TR-B-140

Prestige 4872 / TR-B-850

Futura 4260 / OV-B-310, OVG-310 Futura 4272 / OV-B-320, OVG-320

Classic 4060 / OV-B-340, OVG-340 Classic 4472 / OV-B-380

Vincennes 2 / HGG-490

Rim-To-Wall Installation

Position the unit in the bath area with the

rim edge against the wall framing. Check

foranyframingmodicationswhichmaybe

requiredtoaccommodatepipesorttings

on whirlpool equipped models.

With the unit properly positioned, check for

the following items: (Illust. 1)

l Conrmthepre-leveledbaseblocksare

restingushontheoor

l Conrmdrainposition.

l Conrmtheunitislevelalongeachside

and across each end.

If required, place material under the base

blocks to maintain the unit in a level posi-

tion. After leveling the unit, place a mark

along the bottom edge of the unit rim at

each framing member. Remove the unit and

apply a 3/4” rail to the framing, 1/16” below

the rim mark on the framing (illust. 1). DO

NOT install the 3/4” rail as a rim support.

After repositioning and re-leveling the unit,

securethebaseblockstotheoorbyapply-

ing a bead of construction adhesive to the

underside of each block (illust. 2).

NOTE: Any material place under the base

blocks to keep the unit level must be

structurally sound and applied to ensure the

unit’s weight will be equally distributed over

the entire base.

Deck Surround Framing

Withtheunitsecuredtotheoorstruc-

ture, as shown in illustrations1 and 2, the

framework surrounding the unit can now be

constructed. Due to the design possibilities,

itisimpossibletoprovideexactguidelines

for every type of installation.

The following guidelines apply to every

self-rimming unit regardless of the installa-

tionconguration.Acarefulreviewofthese

guidelines before continuing is important in

avoiding unnecessary problems resulting in

an improper installation (illust. 3, 4, 5, & 6).

a) All materials and construction techniques

must comply with applicable codes for

the installation site.

b) All framing must be square, level, and

adequately designed to provide the

structural (weight bearing) support nec-

essary for the areas use.

c) Provide all acess areas required to com-

ply with applicable codes for the installa-

50-1/4”

9-3/4”

60”

16”

2” Dia. Drain

32”

16-3/4“

4-1/4”

2-1/2” Dia. Overflow

7/8“ Drain

Clearance

Drain CenterOverflow Center 6“

”

Arm Rest

15-7/8“

Beveled Edge

Leveling Supports

2” Rim

19”

11”x 3”

Faucet Area

11”x 3”Faucet Area

Geneva 3260 / TR-B-200, TRG-200

50”

10”

60”

17-3/4”

18-1/4”

2” Dia. Drain

36”

16-3/4“

4-1/4”

2-1/2” Dia. Overflow

1“ Drain Clearance

Drain CenterOverflow Center

6-1/2“

2 Rim”

21”

Arm Rest

15-3/4“

Beveled Edge

19”

15”x 3”

Faucet Area

15”x 3”Faucet Area

Geneva 3660 / TR-B-240, TRG-240

51-3/4”

8-1/2”

60-1/4”

15-5/8”

16-5/8”

2” Dia. Drain

32-1/4”

18“

3”

2-1/2” Dia. Overflow

2-1/4“ Drain

Clearance

Drain CenterOverflow Center 6“

21”

15-3/4“

Leveling Supports

19”

2” Rim

15”x 4”

Faucet Area

15”x 4” Faucet Area

San Salvador 1 / TR-B-100

51-7/8”

8-3/8”

60-1/4”

18”

2” Dia. Drain

36”

18“

3”

2-1/2” Dia. Overflow

2-1/2“ Drain

Clearance

Drain CenterOverflow Center

5-3/4“

21”

15-1/2“

Leveling Supports

19”

2” Rim

15”x 4”

Faucet Area

15”x 4” Faucet Area

San Salvador 2 / TR-B-150

2” Dia. Drain

3”

2-1/2”Dia.

Overflow

2“ Drain

Clearance Leveling Supports

2“ Rim

19”

30“

41-3/4”

12-3/8”

29-3/8”

18”

16”

59-5/8”

21”

29-5/8”

15”x 4”

Faucet Area

Paradise Isle / TR-B-900

tion site. A service access is mandatory

at the pump location on all whirlpool

models for all installations (illust. 4).

d) Appropriate clearances between the

framing and the bottom edge of the rim

must be maintained for the application

ofunderlaymentandthenishmaterial,

plus a 1/16” to 1/8” gap to allow for ap-

plication of a waterproof sealant.

NOTE: Oasis recommends a high qual-

ity silicone based sealant with a mold and

mildew resistant content.

Deck Surround Finishing

Install and seal an appropriate underlay-

mentfortheselectednishmaterialsas

instructed by the manufacturer. Make sure

theunderlaymentextendsunderthetubrim

far enough to provide adequate backing for

thenishmaterial(illust.5).

Applythenishmaterialandsealaccording

tothemanufacturersspecications(illust.5).

Afterallthenishworkiscompleted,care-

fully clean the area and apply an appropri-

ate waterproof sealant between the tub rim

andthenishmaterial.Consultthesealant

container for application instructions (illust. 5).

Rim-To-Wall Finishing

Install and seal an appropriate underlay-

ment to the wall framing for the selected

nishmaterialasinstructedbythemanufac-

turer. On rim-to-wall installations it is recom-

mended that a double layer of underlayment

beappliedtoinsurethenishmaterialedge

willendaboveaatunitsurface(illust.6).

Applythenishmaterial,leaving1/16”to

1/8”clearancebetweenthenishmaterial

edge and the tub surface to allow for seal-

ant application (illust. 6).

Afterallthenishworkiscompleted,care-

fully clean the area and apply an appropri-

ate waterproof sealant between the tub rim

andthenishmaterial.Consultthesealant

container for application instructions (illust. 6).

WARNING!

THE INSIDE UNIT SURFACE SHOULD

BE CLEAR OF ALL LOOSE DEBRIS

AND THE SURFACE PROTECTED

BEFORE STEPPING INSIDE.

Water Supply and Drain Connections

Refer to, and follow, the assembly and

installation instructions provided with the

supply valves and drain system. Carefully

check all connections for leaks.

57-1/4”

8-3/4”

66”

17-1/8”

2” Dia. Drain

34-1/4”

18“

3 ”

2-1/2” Dia. Overflow

2-1/4“ Drain

Clearance

Drain CenterOverflow Center 6“

21”

15-3/4“

Leveling Supports

17-1/8”

1-3/4” Rim

19-1/4”

Arm Rest

15”x 4”

Faucet Area

15”x 4” Faucet Area

Prestige 3466 / TR-B-220 Prestige 4272 / TR-B-140

63-1/8”

7-5/8”

71-3/4”

21”

2” Dia. Drain

42”

18“

3”

2-1/2” Dia. Overflow

2-1/4“ Drain

Clearance

Drain CenterOverflow Center

4-7/8“

21”

15-3/4“

Leveling Supports

19-1/4”

1-3/4”

Arm Rest

15”x 4”

Faucet Area

15”x 4” Faucet Area

63-1/2”

8-1/8”

71-5/8”

24”

2” Dia. Drain

48”

18“

3”

2-1/2” Dia. Overflow

2-3/4“ Drain

Clearance

Drain CenterOverflow Center

5-1/4“

”

15-1/4“

Leveling Supports

19-1/4”

1-3/4

Rim”

15”x 4”

Faucet Area

15”x 4” Faucet Area

Arm Rest

Prestige 4872 / TR-B-850

2” Dia. Drain

3”

2-1/2” Dia.

Overflow

1-3/4“ Drain

Clearance Leveling Supports

2“

Rim

19”

36“

41-3/4”

12”

29-3/4”

16-1/4”

18”

71-1/2”

35-1/2”

21”

15”x 4”

Faucet Area

Andros Isle / TR-B-400

UNIT SURFACE CARE

WARNING!

NEVER USE ABRASIVE MATERIALS,

OR ABRASIVE CLEANERS

ON THE UNIT SURFACE!

EXTREME CAUTION is urged regarding

the use of any cleaner, acid or solvent

on the unit surface.

READ AND FOLLOW PACKAGE

INSTRUCTIONS FOR ALL

PURCHASED CLEANING PRODUCTS!

Through routine use the surface can col-

lect residues from soap, bath additives

and natural body oils. Additional deposits

can also collect from minerals or particles

found in the water. After each use, wipe the

excesswaterfromtheunit.Thispractice

will reduce the buildup of deposits and help

maintain the natural unit lustre.

Following a thorough surface cleaning,

anapplicationofqualityautomotivewax

will help reduce major accumulations. The

actualscheduleforcleaningandwaxingwill

depend on unit usage and water quality.

WARNING!

NEVER APPLY WAX TO THE FLOOR!

uRoutine Cleaning: Mild, non-abrasive

cleanerspecicallyformulatedforgelcoat

and acrylic surfaces recommended. (Rinse

surface thoroughly)

uHeavy Soap Deposits: Liquid ammonia

household cleaner, applied full strength.

(Rinse surface thoroughly)

uStubborn Stains: Liquid household

cleanerorhydrogenperoxideapplied

full strength. Place a saturated clean rag

directly on stain and let stand several hours.

(Rinse surface thoroughly)

uHard Water Scales: Liquid scale remover

or white vinegar, applied full strength.

(Rinse surface thoroughly)

uMold/Mildew: Liquid mildew remover or

baking soda and water paste. (Apply paste

andallowtozzseveralminutes.)(Rinse

surface thoroughly)

uConstruction Adhesive: Soften with a

hand held hair dryer and peel off adhesive.

(Caution is advised when using any electri-

cal device near water.)

60-5/8”

11-3/8”

72”

18-1/8”

2” Dia. Drain

36-1/4”

16-3/4“

4-1/4”

2-1/2” Dia. Overflow

1-1/8“ Drain Clearance

Drain CenterOverflow Center

7-1/4“

Leveling Supports

19”

Arm Rest

15-5/8“

Beveled Edge

21”

2” Rim

15”x 4”

Faucet Area

15”x 4” Faucet Area

Geneva 3672 / TR-B-270, TRG-270

2” Dia. Drain

4-1/4”

2-1/2” Dia. Overflow

1“ Drain

Clearance

Drain CenterOverflow Center

5-3/4“

Leveling Supports

2“

Rim

Beveled Edge

16-1/2”

15-1/2” 20-3/4”

18-3/4”

51-1/2”

60”

9“

42”

21”

15”x 4”

Faucet Area

15”x 4” Faucet Area

Futura 4260 / OV-B-310, OVG-310

2” Dia. Drain

2-3/4”

2-1/2” Dia.

Overflow

1-3/8“ Drain

Clearance Leveling Supports

2“ Rim

18”

16-5/8”

18-3/4”

40”

59-3/4”

20”

20-3/4”

9-1/4”

20”

50-1/2”

Drain CenterOverflow Center

6-1/4”

Classic 4060 / OV-B-340, OVG-340

2” Dia. Drain

3” 2-1/2” Dia. Overflow

1-1/8“ Drain

Clearance Pre-Leveled Base

2-1/4“

Rim

Arm Rest

19-3/4”

36“

42”

10-7/8”

31-1/8”

22”

36“

72“

19”

17-7/8”

Neck Rest

Neck Rest 1-1/4”

Arm Rest 15”x 4”

Faucet Area

Vincennes 2 / HGG-490

For adhesive residue, apply rubbing alcohol

or nail polish remover, full strength. (Rinse

surface thoroughly)

WARNING!

BATH MATS AND OTHER ITEMS

HELD IN PLACE USING SUCTIONS

MUST BE REMOVED FROM THE UNIT

SURFACE AFTER EACH USE.

OVER AN EXTENDED PERIOD,

FAILURE TO REMOVE

SUCTION ATTACHED ITEMS

WILL DAMAGE THE UNIT SURFACE.

2” Dia. Drain

4-1/4”

2-1/2” Dia. Overflow

1-3/4“ Drain

Clearance Leveling Supports

2“ Rim

Beveled Edge

18 -3/4”

36“

42”

8-5/8”

33-3/8”

14-3/4”

16-1/2”

71-3/4”

35-3/4”

20-3/4”

15”x 4”

Faucet Area

15”x 4”

Faucet Area

Futura 4272 / OV-B-320, OVG-320

2. The factory-leveled block base MUST fully

rest on the floor and be used as the unit support.

Shimming of one or more blocks may be

necessary to maintain level.

3/4” rail

positioned

1/16”

below rim

Confirm drain position.

Confirm leveling blocks are flush on floor

Confirm top of tub is level along both

sides and at each end of unit

3. The base and/or whirlpool

system may extend to the outer edge

of the unit, making it impossible to

insert the unit in a deck cut out without

causing damage.

4. Selective placement of

framing members may be

required to avoid damaging

whirlpool system components.

1. The installation CANNOT allow the

rim to support the weight of the unit.

3/4” rail positioned

1/16” below rim

2” Dia. Drain

2-3/4”

2-1/2” Dia. Overflow

1-1/4“ Drain Clearance Leveling Supports

2“

Rim

18”

16-3/4”

18-3/4”

43-3/4”

71-3/4”

11-3/4”

32”

20-3/4”

35-3/4” 36”

15”x 2”

Faucet Area

Classic 4472 / OV-B-380

Finish

Layer

Wall Framing

Waterproof

Sealant

Tub

Rim

Double Layer

Underlayment

3/4 inch

Rail

Illustration 6

All framing must be square and level using the

appropriate framing material and construction

techniques for adequate support.

Allow spacing under rim for the underlayment, the

finish material plus 1/16 to 1/8 inch for sealant.

Illustration 3

A 16 inch high x 21 inch wide

clear access opening is required

at the pump location for all

whirlpool equipped units.

Illustration 4

Underlayment

Deck

Framing

Finish Layer

Waterproof

Sealant

Tub Rim

Illustration 5

Underside

of Bathing

Well

Pre-Leveled Block Bases

Site Applied Construction Adhesive

Underside

of Deck

Unit Rim

Illustration 2

2. The factory-leveled block base MUST fully

rest on the floor and be used as the unit support.

Shimming of one or more blocks may be

necessary to maintain level.

3/4” rail

positioned

1/16”

below rim

Confirm drain position.

Confirm leveling blocks are flush on floor

Confirm top of tub is level along both

sides and at each end of unit

3. The base and/or whirlpool

system may extend to the outer edge

of the unit, making it impossible to

insert the unit in a deck cut out without

causing damage.

4. Selective placement of

framing members may be

required to avoid damaging

whirlpool system components.

1. The installation CANNOT allow the

rim to support the weight of the unit.

3/4” rail positioned

1/16” below rim

Illustration 1

INST-0720.02 / 101514

Oasis Lifestyle, LLC - 1400 Pidco Drive - Plymouth, Indiana 46563

Oasis Lifestyle Product Assurance Program

Bathing and Shower Unit Structure & Surface Finish Limited Warranty

OasisLifestyleprovidesaperformanceassuranceprogramforunitstructuralintegrityandsurfacenishcoveringave

(5) year period from the date-of-purchase on GELCOAT, and covering a ten (10) year period from the date-of-purchase on

VACUUM FORMED ACRYLIC product, for the original purchaser and subsequent consumer. This Oasis limited warranty pro-

gramaddressesspecicdefectsintheproduct,andtheworkmanshipassociatedwiththemanufactureoftheOasisbathing

andshowerproduct.Thespecicdefectscoveredmustresultinasignicantlyalteredappearanceand/oraffecttheintended

performance standards for the product under normal residential use.

Hydro-Massage Systems (water recirculation & air), Option & Accessories Limited Warranty

Oasis Lifestyle provides a performance assurance program for their hydro-massage systems (herein called ‘system’), and

their options and accessories covering a two (2) year period from the date-of-purchase for the original purchaser and subse-

quentconsumer.ThisOasislimitedwarrantyprogramaddressesspecicdefectsinthesystemcomponents,andthework-

manship associated with the assembly of the systems, along with offered options and accessories installed by Oasis, on an

Oasisunit.Thespecicdefectscoveredmustresultinasignicantlyalteredappearanceand/oraffecttheintendedperfor-

mance standards for the system, the option and/or the accessory.

Duringthecoverageperiod,Oasiswill,atitsdiscretion(followingavericationbyanauthorizedOasisrepresentative),either

provideserviceorsupplyareplacementproductwithoutcharge,butexcludinganycostassociatedwiththetransportation,

removalofand/orreinstallationoftheunit(module).FailuretoallowrequestedinspectionbyanauthorizedOasisrepresenta-

tive,and/orfailuretoprovideadequateaccessibilityforanauthorizedinspection,and/orserviceperformedpriortodocument-

edauthorizationfromOasisLifestyle,LLC.,maydelayservice,and/orpossiblyterminateanywarrantycoverage,andremove

any liability to Oasis Lifestyle, LLC.

This ‘Product Assurance Program’ does not cover service resulting the following:

a) Impropereldinstallationoftheproduct,system,option,accessory,and/orsurroundingstructure

modications,and/orutilityserviceconnectionsbeyondtherecommendationssuppliedbyOasisandwithinthe

scope of applicable codes and ordinances; or

b) Carelessness,damage,abuse,misuse,negligence,impropercare,re,ood,oractsofGod;or

c) Non-conforming use, including any use beyond those intended for the product, system, option and/or

accessory, including failure to follow the Prescribed Care and Maintenance Instructions; or

d) Anyunauthorizedalterationsormodicationstotheproduct,system,option,accessoryand/ortheindividual

parts or components supplied by Oasis.

e) Any surface and/or component staining, discoloration, component failure and/or build-up caused as a result of

water chemistry or water quality at the site.

f) Service resulting from normal use and wear for the product, system, option and/or accessory.

Repairorthesupplyingofreplacementproductand/orcomponents,underthislimitedwarrantyprogram,shallbetheex-

clusive remedy. Oasis Lifestyle, LLC., shall not be liable for any incidental or consequential damages, including damages to

thebuilding/structure,thecontents,theoccupants,orbreachofanyexpressedorimpliedwarranties.OasisLifestyle,LLC.,

doesnotrecognize,norauthorizesanypartytoprovideimpliedorwrittenwarrantiesregardingaproduct,system,optionand/

oraccessoriestnessforaparticularpurpose,normodifythetermsofthelimitedwarrantybeyondthosestated.

Somestatesdonotallowtheexclusionorlimitationofincidentalorconsequentialdamages,orallowlimitationsonthedura-

tionofanyimpliedwarranty.Therefore,theaboveexclusionsand/orlimitationsmaynotapply.

THIS WARRANTY PROVIDES SPECIFIC LEGAL RIGHTS, WHICH CAN VARY FROM STATE-TO-STATE.

800.638.8556

HomeInnovation.com

The manufacturer represents that the product to which this

label is affixed (a) duplicates samples independently

tested by Home Innovations Research Labs and certified

to conform to the requirements of HUD UM Bulletin 73a

and the appropriate ANSI Z124 and ICC/ANSI A117.1

standards, and (b) has been manufactured under quality

controls deemed appropriate by the manufacturer and

periodically reviewed by the certifier.

Oasis Lifestyle, LLC

Plymouth, IN

6006

800.638.8556

HomeInnovation.com

The manufacturer represents that the product to which this

label is affixed (a) duplicates samples independently

tested by Home Innovations Research Labs and certified

to conform to the requirements of HUD UM Bulletin 73a

and the appropriate ANSI Z124 and ASME A112.19.7

standards, and (b) has been manufactured under quality

controls deemed appropriate by the manufacturer and

periodically reviewed by the certifier.

Oasis Lifestyle, LLC

Plymouth, IN

6006

Este manual sirve para los siguientes modelos

Otros manuales de Bañera de Oasis

Oasis

Oasis BA-5429 Manual de usuario

Manuales populares de Bañera de otras marcas

Agua

Agua BARTOLI-66 Manual de usuario

PAA

PAA PRELUDE Manual de usuario

BETTE

BETTE SILHOUETTE Manual de usuario

Kohler

Kohler K-820-GC Guía de inicio rápido

American Standard

American Standard Whirlpool/Bathing Pool 2748.XXXW Manual de usuario

Oliveri

Oliveri Naples Manual de usuario

Lyons

Lyons Elite ETLxx663219 Series Manual de usuario

Woodbridge

Woodbridge BJ500 Instrucciones de montaje

Whirlpool

Whirlpool Ariel ARL-702 Manual de usuario

TEIKO

TEIKO EXCELLENT DUO Manual de usuario

American Standard

American Standard Colony 5-1/2' x 32" Manual de usuario

American Standard

American Standard 3052OD.X0X Guía de inicio rápido

Kohler

Kohler K-1111-H2 Guía de inicio rápido

agape

agape MARSIGLIA AVAS1075 Manual de usuario

Kohler

Kohler K-1151 Instrucciones de montaje

Kohler

Kohler K-1158 Guía de inicio rápido

Kohler

Kohler K-1244 Instrucciones de montaje

Kallista

Kallista P50045-G5 Instrucciones de montaje