NXP Semiconductors SE050 Manual de usuario

AN12397

EdgeLockTM SE050 Quick start guide with i.MX6UltraLite

Rev. 1.2 — 17 December 2019 Application note

534512

Document information

Information Content

Keywords EdgeLock SE050, EdgeLock Plug & Trust middleware, i.MX6UltraLite

Abstract This document explains how to get started with the OM-SE050ARD board

and i.MX6UltraLite board. This guide provides detailed instructions for

connecting the boards, installing the software, running the EdgeLock SE050

Plug & Trust project examples and executing the pySSSCLI tool.

NXP Semiconductors AN12397

EdgeLockTM SE050 Quick start guide with i.MX6UltraLite

Application note Rev. 1.2 — 17 December 2019

534512 2 / 21

Revision history

Revision

number

Date Description

1.0 2019-06-08 First document release.

1.1 2019-06-20 Update board figures

1.2 2019-12-17 Corrected OM-SE050ARD J14 jumper setting.

NXP Semiconductors AN12397

EdgeLockTM SE050 Quick start guide with i.MX6UltraLite

Application note Rev. 1.2 — 17 December 2019

534512 3 / 21

1 Read this first

The hardware used in this document is the following:

1.1 Required hardware

1. OM-SE050ARD development kit:

Table 1. OM-SE050ARD development kit details

Part number 12NC Content Picture

OM-SE050ARD 935383282598 EdgeLock SE050

development board

2. i.MX6Ultralite board

Table 2. i.MX6Ultralite

Part number 12NC Content Picture

MCIMX6UL-EVKB 935328353598 i.MX6UltraLite

evaluation kit

NXP Semiconductors AN12397

EdgeLockTM SE050 Quick start guide with i.MX6UltraLite

Application note Rev. 1.2 — 17 December 2019

534512 4 / 21

2 Hardware setup

The hardware setup consists of two steps:

1. Mounting the boards, as described in Section 2.1

2. Configuring OM-SE050ARD jumpers, as described in Section 2.2

2.1 Mounting the boards

1. Connect the OM-SE050ARD board on top of the i.MX6UltraLite board using the

Arduino connectors as shown in Figure 1

Figure 1. Arduino connectors of OM-SE050ARD and i.MX6UltraLite boards

Note: In case the i.MX6UltraLite board does not come with the Arduino headers

assembled by default, they can be easily soldered in the dedicated mounting holes.

2.2 Jumper configuration

1. Make sure the jumper settings in your OM-SE050ARD board are configured as shown

in Figure 2

Figure 2. Jumper configuration for i.MX6UltraLite board

NXP Semiconductors AN12397

EdgeLockTM SE050 Quick start guide with i.MX6UltraLite

Application note Rev. 1.2 — 17 December 2019

534512 5 / 21

For more information about the OM-SE050ARD jumper settings, refer to AN12395 OM-

SE050ARD hardware overview document.

NXP Semiconductors AN12397

EdgeLockTM SE050 Quick start guide with i.MX6UltraLite

Application note Rev. 1.2 — 17 December 2019

534512 6 / 21

3 Software setup

The software setup consists of:

1. Preparing a micro-SD card with the pre-compiled Linux image for i.MX6UltraLite

board, as described in Section 3.1.

2. Installing the USB to UART Bridge VCOM driver in your laptop, as described in

Section 3.2.

3. Installing TeraTerm terminal application, as described in Section 3.3.

4. Booting the i.MX6UltraLite board, as described in Section 3.4.

3.1 Micro-SD card preparation

To prepare the micro-sd card with the pre-compiled Linux image that includes the

EdgeLock SE050 Plug & Trust middleware, you need to:

1. Download from www.nxp.com/se050 the EdgeLock SE050 Plug & Trust middleware

SD Card Image. This image contains the EdgeLock SE050 Plug & Trust middleware

pre-installed on a bootable IMX6UL-EVK SD Card Image.

2. Download and install Win32 Disk Imager software. Win32 Disk Imager is a Windows

open source program to format SD card images. Instead of Win 32 Disk Imager, you

could also use any other software for this operation.

3. Plug your micro-SD card in your laptop.

4. Open Win 32 Disk Imager, (1) select from your file system the pre-compiled Linux

image you downloaded from the website and (2) click the Write button as shown in

Figure 3.

Figure 3. Micro-SD card preparation with Win32 Disk Imager software

3.2 Drivers

To install the i.MX6UltraLite drivers, follow these steps:

1. Plug the power supply and connect the USB cable to your laptop as shown in

Figure 4.

NXP Semiconductors AN12397

EdgeLockTM SE050 Quick start guide with i.MX6UltraLite

Application note Rev. 1.2 — 17 December 2019

534512 7 / 21

Figure 4. Plug the power supply and connect the USB cable to your laptop

2. Download the USB to UART Bridge VCOM driver for your processor (either 32 or 64

bits). Install the driver by following the setup wizard until it is finished.

3. Unplug and plug your board.

4. Go to your Device Manager, and check that your board is recognized and assigned

to a port number (COMxx). Write down the assigned port number (COMxx) as it is

needed in the next steps. Your Device Manager should look like Figure 5

NXP Semiconductors AN12397

EdgeLockTM SE050 Quick start guide with i.MX6UltraLite

Application note Rev. 1.2 — 17 December 2019

534512 8 / 21

Figure 5. Check i.MX6UltraLite board is recoginized in Device Manager

3.3 Terminal setup

We need to install a terminal application, for instance TeraTerm, to communicate and

view the serial output of the i.MX6UltraLite board from our laptop. To setup TeraTerm

application:

1. Download TeraTerm and run the installer.

2. Launch TeraTerm, click Serial option and select from the drop down list the COM

port number assigned to your i.MX6UltraLite board as shown in Figure 6. If the serial

option is not enabled for you, your i.MX6UltraLite board might not be recognized. In

that case, please repeat the driver installation described in Section 3.2.

NXP Semiconductors AN12397

EdgeLockTM SE050 Quick start guide with i.MX6UltraLite

Application note Rev. 1.2 — 17 December 2019

534512 9 / 21

Figure 6. Open a TeraTerm serial connection

3. Go to Setup > Serial Port and configure the terminal to 115200 baud rate, 8 data bits,

no parity and 1 stop bit and click OK as shown in Figure 7

Figure 7. Configure TeraTerm serial port connection

3.4 Booting the i.MX6UltraLite

To boot the i.MX6UltraLite, please do the following:

1. Insert the micro-SD card with the pre-compiled Linux image into the card slot as

shown in Figure 8

NXP Semiconductors AN12397

EdgeLockTM SE050 Quick start guide with i.MX6UltraLite

Application note Rev. 1.2 — 17 December 2019

534512 10 / 21

Figure 8. Insert the Micro-SD card

2. Configure the board switches as follows

•SW601 (Boot Device Select Switch): OFF, ON, OFF, OFF (from 4-1 bit)

•SW602 (Boot Mode Select Switch): ON, OFF (from 1-2 bit)

3. Make sure the i.MX6UltraLite switches are set as shown in Figure 9

Figure 9. Configure i.MX6UltraLite board switches

4. Make sure your board is connected to the power supply and to your laptop using a

USB cable and TeraTerm serial port configured (see Section 3.3).

5. Turn on the power supply switch to boot up the board. The power supply button is

shown in Figure 10.

Otros manuales para SE050

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Microcontrolador de NXP Semiconductors

NXP Semiconductors

NXP Semiconductors PN7462 series Manual de usuario

NXP Semiconductors

NXP Semiconductors MTRCKTSPS5744P Manual de usuario

NXP Semiconductors

NXP Semiconductors ASUG Manual de usuario

NXP Semiconductors

NXP Semiconductors OM5578 PN7150 Manual de usuario

NXP Semiconductors

NXP Semiconductors freescale KV4 Series Manual de usuario

NXP Semiconductors

NXP Semiconductors Freescale TWR-MECH Manual de usuario

NXP Semiconductors

NXP Semiconductors freescale Kinetics TWR-K60N512-KEIL Manual de usuario

NXP Semiconductors

NXP Semiconductors MRF101AN Manual de usuario

NXP Semiconductors

NXP Semiconductors P89LPC952 Manual de usuario

NXP Semiconductors

NXP Semiconductors MPC5566 Manual de usuario

NXP Semiconductors

NXP Semiconductors ARM Cortex M0+ Manual de usuario

NXP Semiconductors

NXP Semiconductors MPC57xx Instrucciones de instalación y funcionamiento

NXP Semiconductors

NXP Semiconductors LPC55S0x Manual de instrucciones

NXP Semiconductors

NXP Semiconductors TWR-K60N512-IAR Manual de usuario

NXP Semiconductors

NXP Semiconductors Freescale Flexis MCF51MM256 Manual de usuario

NXP Semiconductors

NXP Semiconductors Freescale MC9S12XE Series Manual de usuario

NXP Semiconductors

NXP Semiconductors UM108 Series Manual de usuario

NXP Semiconductors

NXP Semiconductors LPC18xx series Manual de usuario

NXP Semiconductors

NXP Semiconductors TWR-K21F120M Manual de usuario

NXP Semiconductors

NXP Semiconductors LPC1102 Manual de usuario

NXP Semiconductors

NXP Semiconductors S32R372141EVB Manual de usuario

NXP Semiconductors

NXP Semiconductors LPC11E Series Manual de usuario

NXP Semiconductors

NXP Semiconductors NTAG I2C plus Manual de uso y cuidado

NXP Semiconductors

NXP Semiconductors P89LPC980 Manual de usuario

Manuales populares de Microcontrolador de otras marcas

AMS

AMS AS7261 Demo Kit Manual de usuario

Novatek

Novatek NT6861 Manual de usuario

Espressif Systems

Espressif Systems ESP8266 SDK Guía de configuración

Nuvoton

Nuvoton ISD61S00 ChipCorder Guía

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Manual de usuario

Texas Instruments

Texas Instruments Chipcon CC2420DK Manual de usuario

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Manual de usuario

NEC

NEC 78GK0S/K 1+ Series Instrucciones de instalación y funcionamiento

Mikroe

Mikroe SEMITECH N-PLC Click Instrucciones de instalación y funcionamiento

Intel

Intel Agilex Manual de usuario

Cypress

Cypress CY4607 HX2VL Manual de usuario

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Manual de usuario

Texas Instruments

Texas Instruments TMS320F2837 D Series Manual de usuario

CYPRES

CYPRES CY14NVSRAMKIT-001 Manual de usuario

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM Manual de usuario

Espressif Systems

Espressif Systems ESP8266EX Instrucciones de funcionamiento

Abov

Abov AC33M8128L Manual de usuario

Laird

Laird BL654PA Manual de usuario