Novus 8000 Series Manual de usuario

U s e r ’s m a n u a l

8000 series IP PTZ cameras

8000 series IP PTZ cameras user manual, version 1.0

NOTICE:

Following user’s manual refers to PTZ control part only. Please read installation manual prior using

PTZ camera.

After proper ActiveX installation and logging user interface of the camera appears.

In the lower part of the user interface there is tool bar. Following tow icons enables PTZ-related

features

There are two ways of pan/tilt/zoom control:

1. 3D on-screen navigating

In order to move the camera simply click on the image using left mouse button. The camera moves so

that the selected point become a centre of the view.

In order to zoom-in select desired part of the image, click on left mouse button, keep it pressed and

draw a rectangle dragging down and right. Once the button is released the camera zoom-in so that

selected part is enlarged to the whole video screen.

In order to zoom-out select desired part of the image, click on left mouse button, keep it pressed and

draw a rectangle dragging up and left. Once the button is released the camera zoom-out so that selected

part is enlarged to the whole video screen.

INTRODUCTION

8000 series IP PTZ user manual, version 1.0

Zoom-in Zoom-out

2. PTZ Panel

Other way of camera control is using PTZ panel where appropriate icons control corresponding camera

action and function. Below there is a general appearance of the PTZ panel

Further chapters of the manual describe function of each part of the panel.

The PTZ control panel includes:

Preset - adding, deleting and invoking presets

Track - adding, deleting and invoking observation tracks

Scan - adding, deleting and invoking scans

Tour - adding, deleting and invoking tours

Idle - setting camera reaction to operator inactivity

Timer - setting the schedule

Extension - setting the reboot action

PTZ PANEL

8000 series IP PTZ cameras user manual, version 1.0

2.1. Camera control

On the left side of the panel there are navigation buttons intended for control the camera in real time.

After moving the cursor on particular elements of the panel information about their functions appears.

PTZ functions:

1. Speed - this parameter determines speed of the camera’s direction changing .

It can be adjusted by using sliding bar or by entering user-defined value in the window

next to it. Range of this value is 0 to 8.

2. Navigation buttons - allows manual control of the camera toward one of 8 directions.

3. Focus - clicking and holding one of these icons allows to gradually increase or decrease

the camera focus.

4. Autofocus - clicking and holding this icon allows the program to automatically adjust

the camera focus.

5. Iris - clicking and holding one of these icons allows to gradually open or close the

camera iris.

6. North - clicking this icon after setting the camera to the north calibrates coordinate

system of the camera.

7. Zoom - clicking and holding one of these icons allows to gradually increase or decrease

the camera zoom.

PTZ PANEL - CAMERA CONTROL

8000 series IP PTZ user manual, version 1.0

2.2 Preset tab

The Preset tab allows to add, delete and invoke predefined camera positions.

NOTE:

The preset tab allows to save up to 400 presets, except these with ID:

64; 92; 93; 97; 99; 250; 251; 252; 253 which are reserved for special options.

2.2.1 Adding a preset

To add a preset, at the beginning point the camera to the chosen position, then assign an identification

number from the drop-down list in the ID field (1) and assign a name in the Name field (2). Clicking the

plus button (3) saves the current camera position.

2.2.2 Deleting a preset

To delete a preset, select the preset from the drop-down list Preset (6), then click the button with cross

icon (5). Deleting a preset makes it no longer available for selection in the list (6).

2.2.3 Invoking a preset

To invoke a preset, select the preset from the drop-down list in the Preset field (6) and then click the

button with arrow icon (4). This automatically moves the camera to the saved position.

PTZ PANEL - PRESET

543

8000 series IP PTZ cameras user manual, version 1.0

2.3 Track tab

The Track tab allows to add, delete and invoke predefined tracks along which the camera will move.

The program allows to save up to 6 tracks.

2.3.1 Adding a track

To define a new track, select an ID number from the drop-down list in the ID field (1) and assign

atrack name in the Name field (2). Then point the camera to the starting point. After clicking the

play button (4) each movement of the camera caused by the navigation buttons is saved until clicking

the stop button (3). From then, the track has been saved and is available for selection in the

Track field (7).

2.3.2 Deleting a track

To delete a track, select it from the Track list (7), then press the button with cross icon (6). Deleting the

track makes it no longer available for selection in the list (7).

2.3.3 Invoking a track

To invoke a track, select it from the Track list (7), then press the button with arrow icon (5). When the

track is invoked, the camera moves firstly to the saved starting point regardless of the previous

position, and then recreates the saved track. When track is finished, the camera returns to the starting

point and repeats this movement until the user uses the navigation buttons or another program function.

PTZ PANEL - TRACK

653

8000 series IP PTZ user manual, version 1.0

2.4 Scan tab

The Scan tab allows to add, delete and invoke the camera scanning between two points.

The program allows to save up to 12 scans.

2.4.1 Adding a scan

To define a new scan, select an ID number from the drop-down list in the ID field(1) and assign a scan

name in the Name field (2). Then point the camera to the position that is the starting point. After

pressing the play button (4), point the camera to the end point and press the stop button (3). After

adding, the scan has been saved and from then will is available for selection in the Scan list (7).

2.4.2 Deleting a scan

To delete a scan, select it from the Scan list (7), then press the button with the cross icon (6). Deleting a

scan makes it no longer available for selection in the list (7).

2.4.3 Invoking a scan

To invoke a scan, select it from the Scan list (7), then press the button with the arrow icon (5). Once

activate scan, the camera set at the memorized starting point regardless of the previous position and

next moves to the end point. The camera repeats this movement and scans the area between the start

and end points until the user uses the navigation buttons or another program function.

PTZ PANEL - SCAN

6543

8000 series IP PTZ cameras user manual, version 1.0

2.5 Tour tab

The Tour tab allows to add, delete and invoke the tour function between predefined presets.

The program allows to save up to 12 tours.

2.5.1 Adding a tour

To add a new tour, select an ID number from the drop-down list in the ID field (1) and assign a tour

name in the Name field (2). Then press the play button (5) which starts the programming process.

To add a preset to the tour, firstly select it from the drop-down list in the Preset field (7) and next

declare the Wait Time (6) in seconds. Wait time is a time the camera waits in selected preset. Confirm

adding a preset by pressing the selection button (3). The same way add next presets to tour, until the

final effect is achieved.

The programming process could be ended with the stop button (4), this action saves the tour in the

Tour list (12).

2.5.2 Deleting a tour

To delete a tour, select it from the Tour field (12) and then press the button with the cross icon (9).

Deleting a patrol makes it no longer available for selection in the Tour field (12).

2.5.3 Invoking a tour

The tour could be invoke by pressing the button with the arrow icon (8) after selecting it from the

Patrol field (12). When a tour is invoked, the camera moves to the first added preset, regardless of the

previous position, and then moves to subsequent presets visible in the Preset field (11), after a

predefined time in seconds, visible in the Wait Time field (10).

PTZ PANEL - TOUR

9854

8000 series IP PTZ user manual, version 1.0

2.6 Idle tab

The Idle tab is used to set the reaction of the camera to the inactivity of the operator.

The idle function could be switched on and off by using the on/off button (1). When the idle function is

enable, select in the Type field (2) the program function which is activated after the waiting time (4),

then select the function name in the Name field (3). The program functions has to be programmed

before.

The waiting time is a period of inactivity of the camera operator after which the appropriate function is

invoke. It is specified in minutes in the field Wait time (4). The entire operation could be confirmed by

the selection button (5).

PTZ PANEL - IDLE

8000 series IP PTZ cameras user manual, version 1.0

2.7 Timer tab

The Timer tab is used to set the action schedule of the various functions of the program during the day.

To access the schedule, click the button with the gear symbol.

To activate the schedule, use the Enable field (1) and select the Timer Mode (10):

Everyday - program functions are invoked in the same order every day.

Once - the program functions are invoked only once, on the day declared in

the Time field (2)

PTZ PANEL - TIMER

Tabla de contenidos

Otros manuales de Cámara de seguridad de Novus

Novus

Novus NVDN-601C-2 Manual de usuario

Novus

Novus NVAHD-2DN5102MH/IR-1 Manual de usuario

Novus

Novus NVIP-4DN2002V/IR-1P Manual de usuario

Novus

Novus NVIP-2C2001D-P/GO Manual de usuario

Novus

Novus NVIP-2VE-6232/WL-II Manual de usuario

Novus

Novus NVIP-2DN2006V/IR-1P Manual de usuario

Novus

Novus NVIP-5DN3614V/IR-1P/F Manual de usuario

Novus

Novus NVIP-5VE-6201 Manual de usuario

Novus

Novus NVAHD-1DN3101H/IR-1 Manual de usuario

Novus

Novus NVIP-1DN3030H/IR-1P Manual de usuario

Novus

Novus NVC-601D/IR Manual de usuario

Novus

Novus NVAHD-2DN5501MV/IR-1 Manual de usuario

Novus

Novus NVIP-3DN7020D/IR-2P Manual de usuario

Novus

Novus NVIP-2V-6502M/F Manual de usuario

Novus

Novus NVIP-2DN5120SD/IRH-2 Manual de usuario

Novus

Novus NVIP-2H-6511/F-II Manual de usuario

Novus

Novus NVIP-8H-6211 Manual de usuario

Novus

Novus NVIP-4DN2001V/IR-1P-II Manual de usuario

Novus

Novus NVIP-8DN3512H/IR-1P Manual de usuario

Novus

Novus NVIP-8VE-6201 Manual de usuario

Novus

Novus NVIP-2V-6411 Manual de usuario

Novus

Novus NVIP-2DN3031AH/IR-1P Manual de usuario

Novus

Novus NVC-201D Manual de usuario

Novus

Novus NVIP-H-8501/T Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario