Novus NVIP-2D-6502/F Manual de usuario
Quick sta rt gu i de
NVIP-2D-6502/F
NVIP-2D-6502/F Quick start guide version 1.0
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
2
THE PRODUCT MEETS THE REQUIREMENTS CONTAINED IN THE FOLLOWING DIRECTIVES:
Information
The device, as a part of professional CCTV system used for surveillance and control, is not designed
for self installation in households by individuals without technical knowledge.
Excluding of responsibility in case of damaging data on a disk or other devices:
The manufacturer does not bear any responsibility in case of damaging or losing data on a disk or other
devices during device operation.
WARNING!
PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT DESCRIBED FOR THE GIVEN
PRODUCT IN USER’S MANUAL AND OTHER DOCUMENTS DELIVERED WITH THE
PRODUCT, OR IF IT DOES NOT ARISE FROM THE USUAL APPLICATION OF THE
PRODUCT, MANUFACTURER MUST BE CONTACTED UNDER THE RIGOR OF EXCLUDING
THE MANUFACTURER’S RESPONSIBILITY FOR THE RESULTS OF SUCH AN ACTION.
DIRECTIVE 2014/30/EU OF THE EUROPEAN PARLIAMENT AND OF THE
COUNCIL of 26 February 2014 on the harmonisation of the laws of the Member States
relating to electromagnetic compatibility (OJ L 96, 29.3.2014, p. 79–106, with changes)
DIRECTIVE 2012/19/EU OF THE EUROPEAN PARLIAMENT AND OF THE
COUNCIL of 4 July 2012 on waste electrical and electronic equipment (WEEE)
(OJ L 197, 24.7.2012, p. 38–71, with changes)
DIRECTIVE 2011/65/EU OF THE EUROPEAN PARLIAMENT AND OF THE
COUNCIL of 8 June 2011 on the restriction of the use of certain hazardous substances in
electrical and electronic equipment (OJ L 174, 1.7.2011, p. 88–110, with changes)
IMPORTANT SAFEGUARDS AND WARNINGS
Pictures in this publication showing camera views can be simulations. Actual camera
images may vary depending on the type, model, settings, observation area, or
environmental conditions.
NVIP-2D-6502/F Quick start guide version 1.0
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
3
WARNING!
THE KNOWLEDGE OF THIS MANUAL IS AN INDESPENSIBLE CONDITION OF A PROPER
DEVICE OPERATION. YOU ARE KINDLY REQUSTED TO FAMILIRIZE YOURSELF WITH
THE MANUAL PRIOR TO INSTALLATION AND FURTHER DEVICE OPERATION.
WARNING!
USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO USER
-SERVICEABLE PARTS INSIDE THIS UNIT. ONLY AUTHORIZED SERVICE PERSONNEL
MAY OPEN THE UNIT
INSTALLATION AND SERVICING SHOULD ONLY BE DONE BY QUALIFIED SERVICE
PERSONNEL AND SHOULD CONFORM TO ALL LOCAL REGULATIONS
1. Prior to undertaking any action please consult the following manual and read all the safety and
operating instructions before starting the device.
2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual
is necessary;
3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct
influence on user’s safety and durability and reliability of the device;
4. All actions conducted by the servicemen and users must be accomplished in accordance with the
user’s manual;
5. The device should be disconnected from power sources during maintenance procedures;
6. Usage of additional devices and components neither provided nor recommended by the producer is
forbidden;
7. You are not allowed to use the camera in high humidity environment (i.e. close to swimming pools,
bath tubs, damp basements);
8. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.)
is not recommended since it may lead to heat build-up and damaging the device itself as a
consequence;
9. Mounting the camera on unstable surface or using not recommended mounts is forbidden.
Improperly mounted camera may cause a fatal accident or may be seriously damaged itself. The
camera must be mounted by qualified personnel with proper authorization, in accordance with this
user’s manual.
10. Device should be supplied only from a power sources whose parameters are in accordance with
those specified by the producer in the camera technical datasheet. Therefore, it is forbidden to
supply the camera from a power sources with unknown parameters, unstable or not meeting
producer’s requirements;
Due to the product being constantly enhanced and optimized, certain parameters and functions
described in the manual in question may change without further notice.
We strongly suggest visiting the www.novuscctv.com/en website in order to access the newest full
manual
IMPORTANT SAFEGUARDS AND WARNINGS
NVIP-2D-6502/F Quick start guide version 1.0
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
4
TABLE OF CONTENTS
1. FOREWORD INFORMATION .....................................................................................5
1.1. General characteristics.........................................................................................5
1.2. Technical specification .......................................................................................6
1.3. Camera dimension ..............................................................................................7
1.4. Package contents..................................................................................................7
2. START-UP AND INITIAL CONFIGURATION .........................................................8
2.1. Description of connectors....................................................................................8
2.2. Description of camera components .....................................................................8
2.3. Zoom and focus adjustment.................................................................................9
2.4. Connecting ethernet cable ...................................................................................9
2.5. Connecting power supply to the camera...........................................................10
2.6. Camera mounting ..............................................................................................10
2.7. Starting the camera ............................................................................................11
2.8. Initial configuration via the web browser..........................................................12
2.9. Security recommendations for network architecture and configuration ...........13
3. NETWORK CONNECTION UTILIZING WEB BROSWER ................................14
3.1. Recommended PC specification for web browser .............................................14
3.2. Connection with camera via web browser .........................................................14
4. USING AND CONFIGURING .....................................................................................16
4.1. The remote preview interface.............................................................................16
5. ELECTRICAL CONNECTIONS AND ACCESORIES...........................................17
5.1. Connecting alarm input/output...........................................................................17
5.2. Memory card installation....................................................................................18
5.3. Connecting audio to the camera .........................................................................18
6. RESTORING FACTORY DEFAULTS .....................................................................19
6.1. Restoring factory settings using the www panel ................................................19
6.2. Restoring factory settings using NMSiptool application ...................................19
6.3. Factory reset with button...................................................................................20
TABLE OF CONTENTS
NVIP-2D-6502/F Quick start guide version 1.0
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
5
1. FOREWORD INFORMATION
1.1. General Characteristics
• Sensor resolution: 2 megapixels
• Mechanical IR cut filter, IR operation capability
• Min. Illumination from 0 lx with IR LED on
• Wide Dynamic Range (WDR) for enhanced image quality in diverse light conditions
• Digital Noise Reduction (DNR)
Lens type: varifocal, f=2.8 - 12 mm/F=1.4
• Built-in LED illuminator: 30 pcs LED
• Built-in webserver: camera configuration through the website
• Compression: H.264, H.265, H.264+, H.265+, H.264 Smart, H.265 Smart, MJPEG
• Max video processing resolution: 1920 x1080
• Multi streaming: compression, resolution, speed and quality defined individually for each video
stream
• ROI functions
• Motion detection
• Private Zones
• RTSP protocol support for video transmission
• Schedule
• Micro SD card up to 128 GB
• Audio input
• Audio output
• Bulid-in microphone
• Alarm input (NO/NC)
• Alarm Output
• Wide range of responses to alarm events: e-mail with attachment, saving file on FTP server,
saving file on SD card, alarm output activation
• Software: NMS (NOVUS MANAGEMENT SYSTEM) for video recording, live monitoring,
playback and remote IP devices administration
• Video Content Analysis (VCA):
Exception
Line Crossing
Region Entrance
Region Exiting
Target Counting
Intrusion
Face Detection
• Power supply: 12VDC, PoE (Power over Ethernet)
FOREWORD INFORMATION
NVIP-2D-6502/F Quick start guide version 1.0
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
6
1.2. Technical specification
FOREWORD INFORMATION
IMAGE
Image Sensor 2 MPX CMOS sensor 1/2.8” SONY STARVIS
Number of Eecve Pixels 1920 (H) x 1080 (V)
Min. Illuminaon 0.0038 lx/F1.4 - color mode,
0 lx (IR on) - B/W mode
Electronic Shuer auto/manual: 1/3 s ~ 1/10000 s
Digital Slow Shuer (DSS) up to 1/3 s
Wide Dynamic Range (WDR) yes (double scan sensor), 120dB
Digital Noise Reducon (DNR) 3D
Defog Funcon (F-DNR) yes
Highlight Compensaon (HLC) yes
Back Light Compensaon (BLC) yes
Reducon of image icker (Anicker) yes
LENS
Lens Type varifocal, f=2.8 ~ 12 mm/F1.4
DAY/NIGHT
Switching Type mechanical IR cut lter
Switching Mode auto, manual, me
Switching Level Adjustment yes
Switching Schedule yes
Visible Light Sensor yes
NETWORK
Stream Resoluon 1920 x 1080 (Full HD), 1280 x 720 (HD), 704 x 576, 480 x 240, 352 x 288
Frame Rate 30 fps for 1920 x 1080 (Full HD) and lower resoluons
Mulstreaming Mode 3 streams
Video/Audio Compression H.264, H.264+, H.264 Smart, H.265, H.265+, H.265 Smart, MJPEG/G.711
Number of Simultaneous Connecons max. 10
Bandwidth 60 Mb/s in total
Network Protocols Support HTTP, TCP/IP, IPv4/v6, UDP, HTTPS, FTP, DHCP, DDNS, NTP, RTSP, UPnP,
SNMP, QoS, IEEE 802.1X, PPPoE, SMTP
ONVIF Protocol Support Prole S
Camera Conguraon from Internet Explorer browser
languages: Polish, English, Russian, and others
Compable Soware NMS, NVR-6000 Viewer
Mobile applicaons SuperLive Plus (iPhone, Android)
OTHER FUNCTIONS
Privacy Zones 4
Moon Detecon yes
Region of interest (ROI) 8
Video Content Analysis (VCA)
tamper, line cross, zone entrance, zone exit, object counng, Scene
Change, Video Blurred, Video Color Cast, objects disnguishing, face
recognion
Image Processing 180˚ image rotaon, sharpening, mirror eect, corridor mode, lens
distoron correcon
Prealarm/Postalarm up to 6 s/up to 120 s
NVIP-2D-6502/F Quick start guide version 1.0
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
7
FOREWORD INFORMATION
1.3. Camera dimensions
1.4. Package contents
After you open the package make sure that the following elements are inside:
• IP camera
• Accessories bag
• Quick start guide
If any of this elements has been damaged during transport, pack all the elements back into the original
box and contact your supplier for further assistance.
Before starting the device familiarize yourself with the description and the role of particular
inputs, outputs and adjusting elements that the device is equipped with.
System Reacon to Alarm Events e-mail with aachment, saving le on FTP server, saving le on SD card,
alarm output acvaon
Restoring default sengs via web browser, using reset buon, via NMS IPTool soware
IR LED
LED Number 30
Range 30 m
Angle 90°
Smart IR yes (soware support)
INTERFACES
Audio Input/Output 1 x Jack (3.5 mm)/1 x Jack (3.5 mm) built-in microphone
Alarm Input/Output 1 (NO/NC)/1 relay type
Network Interface 1 x Ethernet - RJ-45 interface, 10/100 Mbit/s
Memory Card Slot microSD - capacity up to 128GB
INSTALLATION PARAMETERS
Dimensions (mm) 122 (Ф) x 96 (H)
Weight 0.38 kg
Enclosure plasc, white
Power Supply PoE, 12 VDC
Surge protecon TVS 4000 V
Power Consumpon 3 W, 6 W (IR on)
Operang Temperature -10°C ~ 40°C
Humidity max. 95%, relave (non-condensing)
NVIP-2D-6502/F Quick start guide version 1.0
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
8
START-UP AND INITIAL CONFIGURATION
CAUTION!
If the device was brought from a location with lower temperature, please wait until it reaches the
temperature of location it is currently in. Turning the device on immediately after bringing it
from a location with lower ambient temperature is forbidden, as the condensing water vapour
may cause short-circuits and damage the device as a result.
2.START-UP AND INITIAL CONFIGURATION
1
2
3
4
5
2.1. Description of connectors
1. 100 Mb/s Ethernet port (RJ-45
connector)
2. Audio output (HP)
3. Audio input (MIC)
4. Alarm Connectors
1. Alarm output COM
2. Alarm output
3. Alarm input
4. Alarm input GND
5. Power supply 12VDC
1
2
3
4
5
6
2.2. Description of the camera components
INFORMATION! To access the above items
(except the microphone), remove the camera
cover.
1. Light sensor
2. Infrared LEDs
3. Lens adjustment levers
4. Reset button
5. MicroSD card slot
6. Build in microphone
NVIP-2D-6502/F Quick start guide version 1.0
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
9
2.3. Zoom and focus adjustment
To set the focus and focal length, remove the top
cover and then use the available levers to adjust the
field of view and focus.
2.4. Connecting ethernet cable
To maintain tightness of ethernet cable connection, please follow instruction below:
1. Loosen the nut (a) from the main element (b).
2. Run power cable (without RJ-45 connector) though both elements. Then crimp the cable with RJ-45
connector.
3. Connect the cable to the hermetic connector (c), screw main cover (b), then screw the nut (a).
Warning! The 12VDC power connector, the audio and alarm I/O connectors are not hermetic. The user
should ensure the tightness of these sockets on his own.
START-UP AND INITIAL CONFIGURATION
Zoom
Focus
ab
a
b
c
NVIP-2D-6502/F Quick start guide version 1.0
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
10
2.5. Connecting power supply to the camera.
The camera can be powered by an external power supply with parameters compatible with the camera
data or by the RJ45 network socket using PoE technology (IEEE 802.3af). To power the camera via
PoE, use a network switch or PoE adapter compatible with the IEEE 802.3af standard.
Information:
Power supply adapter is not included. Please use power adapter with parameters specified in user’s
manual.
CAUTION:
Do not use power supplies and POE adapters not compatible with IEEE 802.3af standard!
Damage resulting from the use of improper power supply is not covered under warranty!
In order to provide protection against voltage surges/lightning strikes, usage of appropriate
surge protectors is advised. Any damages resulting from surges are not eligible for service
repairs.
2.6. Camera mounting
1. Remove dome cover by turning it counterclockwise
2. Put assembly template of the camera to the desired mounting
surface, and mark drilling holes.
3. Drill mounting, cable and heat removal holes (1) in
previously selected points.
4. Mount the camera base using included screws on smooth
surface
5. Adjust the position of the camera module.
6. Adjust focal length and focus using proper levers.
7. Put on the camera cover again, by turning it clockwise.
START-UP AND INITIAL CONFIGURATION
A
12 VDC +
GND
Tabla de contenidos
Idiomas:
Otros manuales de Cámara IP de Novus
Novus
Novus NVIP-2DN5001C-1P Manual de usuario
Novus
Novus NVIP-12DN5060V/IRH-2P Manual de usuario
Novus
Novus NVIP-5VE-4231 Manual de usuario
Novus
Novus 4000 series Instrucciones de montaje
Novus
Novus NVIP-3000 Series Manual de usuario
Novus
Novus NVIP-2C2011D-P Manual de usuario
Novus
Novus NVIP-TDN3401H/IR/MPX2.0 Manual de usuario
Novus
Novus NVIP-6DN7000C-1P Manual de usuario
Novus
Novus NVAHD-2DN5104MH/IRH-2 Manual de usuario
Novus
Novus NVIP-3000 Series Manual de usuario
Novus
Novus NVIP-ATM200 Manual de usuario
Novus
Novus NVIP-2Q-6101/PIR/W Manual de usuario
Novus
Novus NVIP-12DN7560V/IRH-2P Manual de usuario
Novus
Novus NVIP-3DN3520SD/IRH-2 Manual de usuario
Novus
Novus NVIP-5DN3600C-2P/F Manual de usuario
Novus
Novus NVIP-2DN7020SD-2P Manual de usuario
Novus
Novus NVIP-4DN7000C-1P Manual de usuario
Novus
Novus 2000 series Manual de usuario
Novus
Novus NVIP-2C5005CZ-P/GO Manual de usuario
Novus
Novus NVAHD-2DN3102SD/IR-1 Manual de usuario
