Nortel BayStack 600 Series Manual de usuario
NTP 297-3601-316
DMS-10 Family
600-Series Generics
DIP Switch Settings for Printed Circuit Packs
and Balance Networks
08.01
For Generic 602.20 Standard August 2006
August 2006 08.01 NTP 297-3601-316
For Generic 602.20
Copyright 2006 Nortel,
All Rights Reserved
Printed in the United States of America.
Information subject to change without notice. Nortel reserves the right to make changes in equipment design or
components as progress in engineering or manufacturing may warrant.
DMS
is a trademark of Nortel.
DMS-10 Family
600-Series Generics
DIP Switch Settings for Printed Circuit Packs and
Balance Networks
Nortel Publications: NTP 297-3601-316
08.01
For Generic 602.20
Standard
August 2006
NTP 297-3601-316 08.01 August 2006
For Generic 602.20
ii
Publication history
Issue Date Rating For generic
01.01 August 2000 Preliminary 501
01.02 October 2000 Standard 501
02.01 January 2001 Preliminary 502
02.02 April 2001 Preliminary 502.10
02.03 June 2001 Standard 502.10
03.01 July 2002 Preliminary 503.10
03.02 August 2001 Standard 503.10
04.01 July 2003 Preliminary 504.10
04.02 August 2003 Standard 504.10
05.01 July 2004 Preliminary 505.10
05.01 August 2004 Standard 505.10
06.01 July 2005 Preliminary 601.10
06.01 August 2005 Standard 601.10
07.01 February 2006 Preliminary 602.10
07.01 March 2006 Standard 602.10
08.01 July 2006 Preliminary 602.20
08.01 August 2006 Standard 602.20
NTP 297-3601-316 08.01 August 2006
For Generic 602.20
iv
August 2006 08.01 NTP 297-3601-316
For Generic 602.20
1-1
Section 1: Introduction
1
Scope and purpose of this publication
This Nortel technical publication (NTP) contains the necessary information for
setting dual in-line package (DIP) switches on printed circuit packs and balancing
networks equipped in the DMS-10 switch.
1
OrganizationSection 2 includes information on switch settings for the circuit packs; the switch
setting information is arranged alpha-numerically according to pack code. Section 3
provides information on switch settings for balancing networks; this information is
arranged alpha-numerically according to product code.
Theswitchsetting informationforeachcircuitpackor balancingnetworkincludesthe
following:
• a simplified outline drawing that identifies each DIP-switch and indicates
its approximate position on the pack or balancing network
Note: Since the purpose for these drawings is to indicate DIP-switch
positions, physical components located on the faceplate of the pack, such
as LEDs, lightpipes, and switches,are not depicted. For information about
these components, refer to NTP 297-3601-500, General Maintenance
Information.
• tables indicating the various switch-selectable options and the necessary
settings for each option
1
Notational conventions
All tables in this publication use the following notational convention:
“0" indicates that the switch is in the OFF position.
“1" indicates that the switch is in the ON position.
“-” indicates “not applicable” and that the position of the switch is irrelevant.
August 2006 08.01 NTP 297-3601-316
For Generic 602.20
2-1
Section 2: Switch settings for printed
circuit packs
Figure 2-1: NT0X10 Miscellaneous Scan Detection pack - switch locations
1S1.10
4
1
S1.11
4
1
S1.12
4
1
S1.13
4
1
S1.14
4
1
S1.15
4
1
S1.16
4
1
S1.00
4
1
S1.01
4
1
S1.02
4
1
S1.03
4
1
S1.04
4
1
S1.05
4
1
S1.06
4
Switch settings for printed circuit packs 2-2
August 2006 08.01 NTP 297-3601-316
For Generic 602.20
Note: Settings: 1 = ON, 0 = OFF, - = NOT APPLICABLE. S1 positions
apply to S1.00 through S1.06 and S1.10 through S1.16.
Table 2-A:
NT0X10 Miscellaneous Scan Detection pack - switch settings
Option Switch 1
1 234
Loop Detector 1-1-
Ground or Battery Detector 0-0-
NTP 297-3601-316 08.01 August 2006
For Generic 602.20
2-3 Switch settings for printed circuit packs
Figure 2-2: NT2T03 Miscellaneous Line pack - switch locations
Note: For correct operation of this pack, the software configuration of
the pack options must match the DIP-switch option settings. To configure
or query these options in software, refer to Overlay NTWK or CPK, PACK
prompting sequence, prompts STR1 and STR2.
Note: Settings: 1 = ON, 0 = OFF, - = NOT APPLICABLE.
Table 2-B:
NT2T03 Miscellaneous Line pack - switch settings
Option Circuit 1
Switches
456
Circuit 2
Switches
123
Loop start 011 110
Ground start 100 001
16
Otros manuales para BayStack 600 Series
2
Tabla de contenidos
Otros manuales de Teléfono IP de Nortel
Nortel
Nortel Softphone 2050 Manual de usuario
Nortel
Nortel IP Softphone 2050 Manual de usuario
Nortel
Nortel IP Phone 2007 Manual de usuario
Nortel
Nortel NN43112-102 Manual de usuario
Nortel
Nortel 1535 Guía de referencia
Nortel
Nortel IP Phone 1110 Manual de usuario
Nortel
Nortel Nortel IP Phone 1120E Manual de servicio
Nortel
Nortel 2007 Manual de usuario
Nortel
Nortel Norstar M7208 Manual de usuario
Nortel
Nortel MOG6xx Manual del operador
Nortel
Nortel Networks IP Phone 2002 Manual de usuario
Nortel
Nortel 1140E Manual de usuario
Nortel
Nortel 2001 Guía del usuario
Nortel
Nortel 1140E Manual de usuario
Nortel
Nortel IP Phone 2004 Manual de usuario
Nortel
Nortel IP Phone 2004 Manual de usuario
Nortel
Nortel 2001 Manual del propietario
Nortel
Nortel 7449 Manual de usuario
Nortel
Nortel 1220 Guía de referencia
Nortel
Nortel Meridian M3902 Manual de usuario
