Nilfisk-Advance APC 328 Instrucciones de funcionamiento

INFORMATION

OPERATING

INSTRUCTIONS

APC 328

ALL PURPOSE CLEANER

220-240V220-240V

220-240V

EU & UKEU & UK

EU & UK

5.3.2010

IMPORTANT SAFETY INSTRUCTIONS

This machine is only suitable for commercial use, for example in hotels, schools, hospitals, factories, shops,

and offices other than normal residential housekeeping purposes.

When using any electrical appliance, basic precautions should always be followed, including the following:

WARNING!

To reduce the risk of fire, electric shock, or injury:

•Do not leave the machine unattended when it is plugged-in. Unplug the unit from the power outlet

when not in use.

•Always use a defoamer when foaming occurs to prevent damage to vacuum motor(s).

•Unplug the machine from the power outlet before cleaning or servicing.

•To avoid electric shock, do not expose to rain or snow. Store, and use, indoors.

•Wear hearing protection if desired. The measured sound level of the TW 1500 H is 79 dB(A).

•Do not allow to be used as a toy. Close attention is necessary when used near children.

•Use only the manufacturer’s recommended attachments.

•Inspect the power cord regularly for damage, such as cracking, ageing, or damaged insulation.

Replace the power cord with the same type as original if any damage is found. Do not use with

damaged cord or plug.

•Use approved chemicals only. Never use solvents.

•Do not let the pump run dry.

•If the machine is not working as it should, has been dropped, damaged, left outdoors or flooded with

water, return it to a service center.

•Do not pull the machine by the cord, do not use the cord as a handle, close a door on the cord, or pull

the cord around sharp edges or corners. Do not run the machine over the cord. Keep the cord away

from heated surfaces. To unplug, grasp the plug, not the cord.

•Extension cords must be 12 gauge and no longer than 15 m. Replace the cord or unplug immediately

if the ground prong becomes damaged.

•Never fill the tank with water above 54ºC.

•Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint,

hair, and anything that may reduce air flow.

•Keep loose clothing, hair, fingers, and all parts of body away from openings and moving parts.

•Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes, or any

health endangering dusts. Do not use to pick up flammable or combustible liquids such as gasoline

or use in areas where they may be present.

•Turn off all controls before unplugging.

•Use extra care when cleaning on stairs.

•Liquid ejected at the spray nozzle could be dangerous as a result of its temperature, pressure,or

chemical content.

INSPECTION:

Carefully unpack and inspect your TW 1500 H for shipping damage. Each machine is tested and inspected

before shipping. Any shipping damage incurred is the responsibility of the carrier. You should notify the

carrier immediately if you notice damage to the box or to the machine or parts.

CLEANING SOLUTIONS:

We recommend liquid cleaning chemicals. Powder chemicals may be used, but unless mixed very thoroughly

they could cause a build-up in the pump, lines, heat exchanger and/or quick disconnects. Any problem

caused by a chemical build-up is not covered by warranty. Use a neutral cleaner with a pH between 5 and

10 to avoid premature wear of the pump, seals, and/or other components.

MAINTENANCE:

For optimum performance flush the machine with clear water at the end of each working day. Once a

month, minimum, run a flushing compound through the machine to break up any mineral or chemical build-

up that may have formed. The vacuum motor and the pump do not require any scheduled maintenance;

however, the motor may require replacement brushes after 1000 - 1500 hours. Clean the body with an all-

purpose detergent, and protect it with an automobile interior polish. Lubricate the wheels, castors, and

quick disconnects with an all purpose silicone spray. Refer to the mainenance schedule on page 9.

PARTS AND SERVICE:

Repairs, when required, should be performed by your authorized distributor who maintains an inventory of

original replacement parts and accessories. Call the distributor from whom you purchased this machine if

you need parts and service. Be sure to specify the machine model. Have your serial number at hand.

Serial Number: __________________

Model: APC 328

Purchase Date:_____________

Write the name and phone number of your distributor:

_____________________________________

(and be sure to register your purchase to active your warranty)

YOUR MACHINE

Operator Handle (1): Operator holds onto this handle to move the machine from one location to

another.

Solution Tank Lid (2): This lid screws off so the tank can be filled. The solution fill hose is

tethered to the lid, and hangs inside the arm of the Operator Handle.

Maid’s tote and Recovery tank lid (3): This removable container holds often-used items and has a

handle for easy carrying. The recovery tank lid sits under the maid’s tote and covers the opening in the

Recovery Tank. This is where the operator can access the tank to clean it and the ball float cage. The

tank can be flushed out by running clean warm water into this opening and laying the open drain hose into

a bucket or drain.

Recovery Hose (4): Waste water is picked-up through this hose.

Spray Hose (5): This hose delivers water from the machine to the cleaning tool.

Drain Hose (6): This hose is used to empty the recovery tank. NOTE: hold the end of the hose above

the water level in the tank to avoid sudden, uncontrolled flow of waste water when you remove the cap,

then lower the hose slowly to control the rate of discharge.

Quick Disconnect (7): Point of attachment for the Spray Hose (5).

Castors and Wheels (8): Castors pivot for ease of steering, and large back wheels make it easy to roll

the machine from location to location.

Chemical Feed Lines (9): These clear tubes connect the cleaning chemical containers to the machine

where the chemical can be siphoned into the outlet water from the pump. Metering tips -- used to change

the ratio of water to chemical -- are installed here.

Switch Plate (10): The machine’s on/off switches for the vacuum and for the pump are located here

and this is where the valve to change chemical feeds is located.

Power Cord (11): The 25 ft. power cord connects to a power cord pigtail on the rear of the machine.

Chemical Container Holders (12): Two molded-in bottle holders for chemical jugs.

KNOW YOUR SWITCH PLATE

Vacuum Switch (1): turns on the vacuum motor.

Chemical Valve (2): switches between the two chemical containers. When the selector is pointed

straight down, the valve is off and neither chemical is selected. When the selector is pointed directly

towards one or the other symbols, that chemical is selected.

Solution Pump Switch (3): turns on the solution pump.

Quick Connect (4): this is where solution comes out of the machine and the attachment point for

the solution hose.

METERING TIPS

The chemical metering tips allow you to select the ratio of chemical to water, as the water flows out of

the machine. Insert the correct metering tip for the desired mixture into the chemical siphon tube.

COLOR HOLE SIZE MIX RATION FLOW RATE

Orange 0.007 1 to 128 7,81 ml per 1 l

Pink 0.012 1 to 64 19,53 ml per 1 l

Dark Green 0.014 1 to 50 23,44 ml per 1 l

Yellow 0.016 1 to 32 39,06 ml per 1 l

Light Blue 0.020 1 to 20 46,87 ml per 1 l

Burgandy 0.022 1 to 15 70,33 ml per 1 l

Black 0.048 1 to 5 156,27 ml per 1 l

METERING TIPS

SET-UP AND USE

1) Insert the appropriate metering tips into the chemical feed lines (see illustration, page 5).

2) Fill the holding tank with warm water (not exceeding 54 °C). Do not add any chemical to the tank.

3) Prepare the area for cleaning by emptying waste receptacles, clearing debris, removing paper

products, blowing out vents, and sweeping floors.

4) Connect the 25 ft power cord to the pig-tail on the rear of the machine.

5) PRIME THE PUMP: Attach the priming hose to the outlet quick disconnect and place the open end

of the hose into the recovery tank. Turn on the pump and let it run until the pump is completely

primed (no visible air in the water stream). Turn the pump off.

NOTE: prime the machine before you place the chemical feed tubes into chemical containers.

6) Disconnect the priming hose and attach the solution hose to the quick disconnect.

7) Attach the spray gun to the other end of the solution line.

8) Place chemicals in the molded-in chemical bottle containers on the rear of the machine. Insert one

of the feed lines into one of the chemical containers. Secure the line by screwing on the cap. The

chemical will feed from which ever container the selector valve on the switch plate is turned towards

and when the gun is used in the low pressure setting. Use chemicals with a pH of between 5 and

10. Never add chemicals to the clean water tank.

9) Set the spray gun to low pressure by sliding the pressure selector forward (low pressure = forward;

high pressure = back).

10) Turn on the pump switch (push button) and spray through the gun for a few seconds to fill the

line with solution.

11) Apply the chemical to the walls and fixtures from the bottom up. Spray the floor last as you work

your way out of the room.

12) Allow the chemical to work for the proper amount of dwell time, according to the chemical

manufacturer’s directions. Agitate heavily soiled areas with a scrub brush.

13) Turn off the chemical injector valve by turning the selector to the down position.

14) Set the spray gun to high pressure and rinse the area from the top down.

15) Connect the vacuum hose, attach the squeegee, and turn on the vacuum (rocker switch).

16) Squeegee off the mirrors, pick up the liquid off the floor with the floor tool. If you have the

optional blow dry hose, use it to dry the fixtures.

17) Drain the recovered water into a utility sink or toilet. NOTE: Keep the top of the drain hose higher

than the water level in the tank to avoid uncontrolled discharge of water when you open the cap

onthe hose.

CAUTION

To avoid vacuum motor damage, always use a defoamer any time foam is present.

Before you turn on the vacuum always make sure the filter screen on the ball float is clean and that the

ball can travel freely.

RE-PRIMING THE PUMP

If the pump looses prime between jobs, follow the instructions to PRIME THE PUMP, above. If that

doesn’t get water flowing, put the priming hose into the vacuum inlet hose barb and cover the rest of

the space around the priming hose with your hand. Turn on the vacuum (with the pump also running)

and let the suction of the vacuum assist in getting water into the pump.

APC 328

01-11-09

11 12 13

16A

17A

ITEM PART No. DESCRIPTION

1 600732869 Lid and gasket, recovery tank

2 600732846 Hose kit, drain, priming and vac inlet

3 600732882 Hose kit, water and chemical metering

4 600732871 Metering tips and chemical injector

5 600732889 Filter, electrical noise suppression

6 600732883 Vacuum motor kit, with gasket and hose

7 600732884 Tank, recovery, complete

8 600732874 Vacuum inlet kit

9 600732886 Switch plate kit, complete

10 600732885 Switch kit, two switches

11 600732876 Pallet, component mounting, complete

12 600732848 Lid, with fill hose, holding tank/base

13 600732858 Fasteners kit

14 600732856 Lid and ring, 4”

15 600732873 Power cord, EU

600732887 Power cord, UK

16 600732866 Pump and motor, complete

16A 600732868 Motor, pump drive

17 600732865 Pump, solution, complete, no motor

17A 600732875 Pressure regulator, for solution pump

18 600732877 Filter, pump in-line, with hoses

19 600732854 Vacuum recovery hose, complete, 8 M

20 600732855 Solution hose assembly, 8 M

21 600732847 Quick disconnect kit, with washers

22 600732859 Grommets and foam

23 600732849 Cap, drain, and brass fitting

24 600732850 Castor kit, includes bracket

25 600732852 Wheel kit

26 600732879 Holding tank/base, complete

MISCELLANEOUS PARTS

600732872 Label kit, APC 328

600732888 Repair kit, solution pump

REV B 11-09

APC 328

PARTLIST

220-240V220-240V

220-240V

245

TOOLS AND ACCESSORIES

Tool kit, standard, complete

1 600732862 Squeegee, hand held

2 600732893 Handle, for hand held squeegee

3 600732855 Solution hose

4 600732863 Brush, dual surface

5 600732894 Handle, two piece

6 600732895 Squeegee, for floor

7 600732896 Gun, spray, dual pressure

8 600732860 Handle, straight, black

9 600732881 Tote, carry all

10 600732853 Metering tips, two each

11 600752127 Priming hose, for solution pump

12 600732854 Recovery hose

Optional accessories

1 600732897 Frame, micro fiber mop

2 600732898 Mop, micro fiber (6)

3 56380888 Squeegee assembly, 61 cm

4 56209089 Squeegee assembly, 76 cm

5 600732901 Mount assembly, mechanical, for squeegee heads

6 600732864 Blower hose assembly, with nozzle

123 or 4

MAINTENANCE

TECHNICAL SPECIFICATIONS

Vacuum motor:

Water lift:

Air flow:

Tank constructions:

Height:

Machine weight:

2-stage, 8 amp

23 kpa

100 CFM

Rotationally molded polyethylene

98 cm X 59 X 86.5 cm

50 kg

MAINTENANCE SCHEDULE

ITEM DAILY WEEKLY QUARTELY YEARLY

Flush chemical lines

Check/clean vac inlet filter

Clean solution filter

Check vacuum motor airways

Check pump for leaks

Check vacuum motor brushes *

* Have your distriburor check the carbon brushes once a year or after about 500 hours of operation.

1) Use only approved chemicals at the recommended mix ratios. All chemicals should be

added through the feed system and NOT added directly to the water in the solution

tank to prevent possible damage to the pump, seals, or other components.

2) For optimum performance, flush the Chemical Feed lines after every job by replacing

the chemical containers with containers of clear water and spraying through the gun

until the fluid stream is clear. See the Maintenance Schedule, below.

3) The pump seals and/or valves in the high pressure pumps may need to be replaced

after about 1000 hours of use, if the pump begins to loose performance or to leak.

The pressure regulator valve may need to be when a drop in the spraying pressure at

the tool is apparent.

Otros manuales para APC 328

Tabla de contenidos

Otros manuales de Aspiradora de Nilfisk-Advance

Nilfisk-Advance

Nilfisk-Advance T22 Plus Manual de usuario

Nilfisk-Advance

Nilfisk-Advance GM 80 Manual de usuario

Nilfisk-Advance

Nilfisk-Advance IVB 995-0H/M SD XC Type 22 Manual de usuario

Nilfisk-Advance

Nilfisk-Advance IQ 215 Manual de usuario

Nilfisk-Advance

Nilfisk-Advance 3997 Manual de usuario

Nilfisk-Advance

Nilfisk-Advance Handy Manual de usuario

Nilfisk-Advance

Nilfisk-Advance VHW200 Manual de usuario

Nilfisk-Advance

Nilfisk-Advance Coupe Neo Manual de usuario

Nilfisk-Advance

Nilfisk-Advance GM 80 Manual de usuario

Nilfisk-Advance

Nilfisk-Advance Supreme 100 EU Manual de usuario

Nilfisk-Advance

Nilfisk-Advance One Series Manual de usuario

Nilfisk-Advance

Nilfisk-Advance AERO 21 INOX Manual de usuario

Nilfisk-Advance

Nilfisk-Advance Advance AdVac 12DC Instrucciones de instalación y mantenimiento

Nilfisk-Advance

Nilfisk-Advance VT 60A Manual de usuario

Nilfisk-Advance

Nilfisk-Advance Multi 20 Manual de usuario

Nilfisk-Advance

Nilfisk-Advance S2B Manual de usuario

Nilfisk-Advance

Nilfisk-Advance SW 650 Manual de usuario

Nilfisk-Advance

Nilfisk-Advance 3707 Manual de usuario

Nilfisk-Advance

Nilfisk-Advance ReliaVac 12 Manual de usuario

Nilfisk-Advance

Nilfisk-Advance VHS110 Z22 V230 Manual de usuario

Nilfisk-Advance

Nilfisk-Advance Bravo Manual de usuario

Nilfisk-Advance

Nilfisk-Advance KING GM200 Manual de usuario

Nilfisk-Advance

Nilfisk-Advance Bravo Manual de usuario

Nilfisk-Advance

Nilfisk-Advance VP300 SERIES Manual de usuario

Manuales populares de Aspiradora de otras marcas

Bissell

Bissell LittleGreen Proheat 1425 Series Manual de usuario

Panasonic

Panasonic MC-YL637S147-AE Manual de usuario

NEFF

NEFF N17XH10 0 Series Manual de usuario

LG A9 Series Manual de usuario

Oreck

Oreck Cordless Captura BK51700 Series Manual de usuario

Kogan

Kogan KAVACROBVWA Manual de usuario

Kränzle

Kränzle VENTOS 50 ID Guía del usuario

EVVO

EVVO Ai35 Manual de usuario

DeWalt

DeWalt DWH200D Manual de usuario

Pontec

Pontec Pondomatic Vacuum Cleaner Manual de usuario

Cleanmaxx

Cleanmaxx PC-P007E Manual de usuario

Exido

Exido 240-114 Manual de usuario

RIDGID

RIDGID WD1685AU0 Manual de usuario

Ezviz

Ezviz RE4P Manual de usuario

STG global

STG global TANVAC HDV3000 Manual de usuario

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Manual de usuario

Factory

Factory M3340 Manual de usuario

Shop-Vac

Shop-Vac VN92 SERIES Manual de usuario