Nilfisk-Advance VT 60A Manual de usuario

Nilfisk VT60A

Compressed Air Vacuum

Specifications

Minimum Compressor Required h.p. 20

Air Hose Diameter inches ½

Input Supply Air psi 90

Input Supply Air cfm 70

Maximum Output Airflow cfm 140

Maximum Waterlift at Control Pressure

inches 172

Air Performance air watts 392

Tank Capacity gallons dry bulk 15

Collection Capacity gallons dry bulk 10

Filter Area square inches 2215

Dimensions (L x W x H) inches 21½ x 25¼ x 37½

Container Diameter inches 16 1/8

Weight with Trolley lbs 52

Sound Level dB(A) at 6’6” 77

NILFISK-ADVANCE AMERICA, INC., 300 Technology Drive, Malvern, PA 19355, 1-800-645-3475, www.pa.nilfisk-advance.com

Instructions for Use

Nilfisk Model VT 60A

Compressed Air Vacuum Cleaner

CAUTION: This Nilfisk vacuum cleaner or any other vacuum cleaner

is not to be used in explosion-hazardous areas, as serious injury could result.

Under no circumstances may this cleaner be used safely for the collection of hazardous or toxic

materials unless equipped with a special HEPA* filter that has been installed according to written

instructions from Nilfisk-Advance America.

ATTENTION EMPLOYER: Please ensure that these Instructions for Use are made available and

understood by all of your employees or any other persons who may use this equipment.

To list all toxic and hazardous materials would be beyond the scope of these instructions. It is the

Employer's responsibility to identify, for Employee's and others' information, hazardous or toxic

materials which may be collected by this equipment. Such information must be communicated to your

Employees and other potential users of this equipment.

Your new Nilfisk industrial vacuum cleaner is a precision-engineered instrument designed for

exceptionally fine filtration. Ordinary vacuum cleaners do not have HEPA filters and cannot be used

safely for hazardous dusts. This Nilfisk machine is safe to use as a dust collector for finely ground

materials, as long as certain precautions are taken. Proper care of this cleaner is essential to the

maintenance of its ultra-fine filtering capabilities.

PLEASE READ THESE INSTRUCTIONS COMPLETELY BEFORE OPERATING THIS VACUUM

CLEANER. IF YOU ARE PICKING UP HAZARDOUS OR ULTRA-FINE MATERIALS, BE SURE TO

FOLLOW THE INSTRUCTIONS FOR “HAZMAT” AS OUTLINED BELOW.

MACHINE SETUP

Your new VT 60A vacuum cleaner is shipped with the trolley and handle

assembly installed. For removal and installation of the vacuum from the

trolley, please refer to the instructions below.

REMOVAL/INSTALLATION OF VACUUM FROM TROLLEY

1. Open the clamp in the back of the trolley.

2. Place the vacuum cleaner container in the trolley

with the inlet facing front and center.

3. To tighten or loosen the trolley’s grip on the vacuum container,

adjust the silver clamp located on the back side of the trolley.

4. Open the clamp.

*HEPA – High Efficiency Particulate Air – Retains 99.97% of particles to 0.3 microns.

5. Loosen the lock nut at the base of the screw (photo 1).

6. Loosen the screw itself to relax the grip; tighten the screw to strengthen.

7. Once the adjustment is made, tighten the lock nut to hold the clamp in place.

CHOOSE DISPOSAL OPTION

The VT 60A offers three collection/disposal options, depending on the size and nature of the

application.

1. Disposable Polyliner: For safe and convenient disposal of larger amounts of material, the vacuum

cleaner container may be lined with a disposable polyliner.

A. Lift off the top half of the machine by unlatching the three (3) lower container clips.

B. Open a polyliner and insert it in the container bottom. Begin by placing the entire polyliner

inside the container bottom.

C. Grasp the edge of the polyliner and pull it up into the clip (photo 2).

DO NOT BUNCH OR GATHER POLYLINER IN OR AROUND THE

CLIP as this could affect airflow through the vertical grooves in the

clip once the upper container is installed.

D. Take the remaining polyliner edge and stretch it over the lip of the

vacuum cleaner’s lower container. In order to minimize wrinkling

and gathering, use only as much polyliner as necessary to secure in position.

E. Smooth out the polyliner against the container, leaving as little air between the two as possible.

F. Replace the upper container and venturi housing and fasten the container clips.

2. Direct Collection Into Tank: Material may be collected directly into the tank, in which case no

preparation is necessary. This method is not recommended for hazardous material pickup, as

proper disposal may not be convenient.

3. Collection Into 30 or 55-Gallon Steel Drum:

A. Center 01719800 ring adaptor on drum.

B. Un-clasp lower set of container clips on vacuum.

C. Lift top of vacuum (venturi head and filter chamber) off vacuum container and place in opening

of ring adaptor.

D. Align vacuum clips with the keepers on ring adaptor and tighten.

Once assembly and setup are complete, verify that the ball valve is turned to the OFF position.

Connect the machine to the air supply and turn ball valve to the ON position. NOTE: For

optimum performance, use at least a 20 h.p. compressor in order to supply a minimum of 70 cfm

through a ½” airline I.D. at 90 psi.

EMPTYING

WARNING: If this vacuum cleaner is used to collect hazardous material, do not attempt to open or

empty its contents without personal protective clothing and respiratory protection.

If the VT 60A loses suction power during work, there may be several reasons. The most likely reason

is a full container. If the container is filled with liquid, suction will be cut off abruptly as the ball float

valve closes off airflow; when the container fills with dry or damp material, suction loss is gradual as

the collection bag fills with debris.

1. Before emptying:

A. Turn ball valve to OFF position.

B. Open the bottom clips and lift out the venturi/filter housing.

C. Check the foam impact filter covering the float valve (photo 3).

If it appears caked or dirty, remove it from the float valve and

shake or dust the debris off the filter into the container. If the

filter is freed of clogging debris, it may be put back on the float

valve. If it cannot be cleaned, replace with a new one (#017226-01

for 3-count package). HAZMAT: Each time the machine is

emptied, remove the impact filter, dispose of it with the container

contents and replace with a new filter.

2. Polyliner (Dry Collection)

A. Lift bag out of container and seal for disposal.

B. Place new bag (#017191 for 25-count package) in container according to instructions above.

HAZMAT: Double-bag, seal and label for proper disposal.

C. Replace venturi/filter housing according to the instructions above.

3. Vacuum Container (Drain for Wet Collection)

A. Open drain valve on base of vacuum.

B. When vacuum has drained completely, close valve.

4. If the machine does not regain full suction power after emptying and cleaning or replacing the

impact filter, check the main filter.

A. Turn ball valve to OFF position.

B. Open the top container clips by turning counterclockwise and releasing them from the keepers.

C. Lift off the venturi and put aside.

D. Pull out the main filter plate, which consists of a plate holding the polyethylene filter fingers and

a splashguard.

E. Unscrew the nylon wing nut at the bottom of the splashguard and remove.

F. Separate the splashguard from the filter (photo 4) and empty, if necessary.

G. Examine the filter fingers.

H. If they are dirty or caked with debris, they may be wiped or rinsed clean.

I. If any are split or broken, they may be replaced individually (#017838).

J. After cleaning, reassemble the splashguard and filter and replace the

entire filter plate in the vacuum container, making sure it is properly seated.

K. Replace the venturi top, close the clips and turn the ball valve to the

ON position.

HAZMAT: The entire main filter and splashguard should be thoroughly cleaned during

decontamination.

FILTER REPLACEMENT

To ensure that your Nilfisk vacuum cleaner delivers the years of trouble-free

operation for which it was designed, it is necessary to check and replace filters regularly.

The VT 60A’s internal microfilter and HEPA are located directly under the

venturi housing. Turn the ball valve OFF. Open the container clips and lift

off the venturi.

1. Microfilter: The microfilter is a small white felt sock

(photo 5) which fits over the HEPA filter housing. This filter should

be checked periodically for dirt or discoloration, and should be

changed whenever it is noticeably soiled (#616821).

A. Simply loosen the metal clamp band with a screwdriver and pull the microfilter off the HEPA

housing.

B. Pull the new one on, making sure to pull it up as far as it will go, covering the HEPA housing

completely.

C. Replace the metal band around the filter and tighten. NOTE: Make sure the metal band seats

firmly against the underside of the motor cover. HAZMAT: Do not shake the microfilter since

this can cause liberation of potentially harmful microscopic dust.

Remove carefully and discard with collected debris in a sealable

poly bag.

2. Internal HEPA Cartridge: The vacuum cleaner’s internal HEPA filter

(photo 6) should be changed approximately every fourth time the

microfilter is changed. Exact life will depend on application, frequency

of use and prefilter maintenance.

A. Remove the microfilter by loosening its metal band and pulling it off like a sock. You will now

see the cartridge in its cage-like holder.

B. To remove the cartridge, loosen and remove the four (4) wing nuts from beneath the holder.

C. Pull the metal plate free of the four pegs and carefully remove the filter.

D. Remove the foam gasket. Discard both items and the microfilter with collected debris in a

sealable poly bag.

E. To install the new filter, place the new large, thick foam gasket

in the recess of the filter holder (photo 7).

F. Install the HEPA cartridge, label side out, in the holder.

G. Replace the metal plate and secure it with the wing nuts.

NOTE: Make sure the wing nuts are well tightened to provide

the necessary seal.

H. Install a new microfilter (see instructions above).

I. Replace the venturi on the container, close the clips and turn the ball valve ON.

CAUTION: Use only genuine Nilfisk replacement parts and filter components. The use of substitute

components could pose a grave risk of personal exposure, and will cause all equipment warranties to

be void.

VT60A

Accessories

Polyliners (25/Pkg.)

017191-00

HEPA Replacement Cartridge

017276-31

10’ Plastic Hose Complete

017196-00

Double Curved Aluminum Wand

017193-00

14” Unfinished Floor Nozzle

017192-04 14” Wet Floor Nozzle

017192-00

3” Aluminum Dust Brush

017194-01 11” Plastic Crevice Tool

017195-00

Ring Adaptor for standard

55 gallon drum Tool Box with Mounting Bracket

017198-00 017851-00

WARRANTY

The Nilfisk companies warrant that Nilfisk equipment will be free of defects in workmanship or

material for a period of two years from the date of delivery. Should any failure to conform to this

warranty appear, the Nilfisk companies shall upon notification within such time period, correct

such non-conformity, at its option, either by repairing any defective part or parts, or by replacing a

part or parts provided that the equipment is returned to an authorized Nilfisk service facility. In all

cases freight both ways will be at the expense of the customer. Equipment shall not be returned

without advance notice to, and consent of the Nilfisk companies.

EXCEPT AS SPECIFICALLY SET FORTH HEREIN, THE NILFISK COMPANIES MAKE NO WARRANTIES, EITHER

EXPRESSED OR IMPLIED AS TO ANY MATTER WHATSOEVER, INCLUDING WITHOUT LIMITATION ANY AND

ALL WARRANTIES OF MERCHANTABILITY, FITNESS FOR PURPOSE, OR OTHER WARRANTIES, ALL OF

WHICH ARE EXPRESSLY DISCLAIMED AND EXCLUDED. NEITHER PARTY SHALL BE LIABLE TO THE OTHER

FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO

LOSS OF PRODUCTION, LOSS OF TIME, LOSS OF PROFITS OR OTHER SIMILAR INDIRECT LOSSES WHICH

MIGHT OCCUR AS A RESULT OF DEFECTS, PARTIAL OR TOTAL FAILURE OF THE PRODUCT TO PERFORM

AS SPECIFIED.

Correction of non-conformities or defects in the manner and for the period of time provided above,

shall constitute fulfillment of all liabilities of the Nilfisk companies to the customer, whether based

on contract, negligence or otherwise with respect to, or arising out of such equipment. The

remedies set forth herein are exclusive, and the liability of the Nilfisk companies with respect to

this sale or anything done in connection therewith, whether in contract, in tort, under any warranty,

or otherwise, shall not except as expressly provided herein, exceed the price of the equipment or

part on which such liability is based.

The warranty does not cover repairs due to normal wear and tear, accident, neglect, misuse or

abuse, incorrect installation or use other than as described in the instruction booklet. Breaks in

hoses and cables are not covered. This warranty is rendered void if the motor number plate is

removed or defaced or if repairs are made or attempted by persons not authorized by the Nilfisk

companies.

Tabla de contenidos

Otros manuales de Aspiradora de Nilfisk-Advance

Nilfisk-Advance

Nilfisk-Advance S2B Manual de usuario

Nilfisk-Advance

Nilfisk-Advance GM 100J Sprint Plus Manual de usuario

Nilfisk-Advance

Nilfisk-Advance METEOR Manual de usuario

Nilfisk-Advance

Nilfisk-Advance GD 10 Manual de usuario

Nilfisk-Advance

Nilfisk-Advance GD 930 Manual de usuario

Nilfisk-Advance

Nilfisk-Advance Advance AdVac 12DC Instrucciones de instalación y mantenimiento

Nilfisk-Advance

Nilfisk-Advance Easy Manual de usuario

Nilfisk-Advance

Nilfisk-Advance Bravo Manual de usuario

Nilfisk-Advance

Nilfisk-Advance VP600 Manual de usuario

Nilfisk-Advance

Nilfisk-Advance Multi 20 Manual de usuario

Nilfisk-Advance

Nilfisk-Advance GD 1000 Series Manual de usuario

Nilfisk-Advance

Nilfisk-Advance Alto Filtra Vac 14 Manual de usuario

Nilfisk-Advance

Nilfisk-Advance AWD 320 Manual de usuario

Nilfisk-Advance

Nilfisk-Advance 3707 Manual de usuario

Nilfisk-Advance

Nilfisk-Advance GD 930 Manual de usuario

Nilfisk-Advance

Nilfisk-Advance ReliaVac 12 HP Manual de usuario

Nilfisk-Advance

Nilfisk-Advance WDNI-1 Manual de usuario

Nilfisk-Advance

Nilfisk-Advance UZ 934 Manual de usuario

Nilfisk-Advance

Nilfisk-Advance AERO 21 INOX Manual de usuario

Nilfisk-Advance

Nilfisk-Advance GM 80 Manual de usuario

Nilfisk-Advance

Nilfisk-Advance 961-OL SD XC Manual de usuario

Nilfisk-Advance

Nilfisk-Advance VP300 SERIES Manual de usuario

Nilfisk-Advance

Nilfisk-Advance VHS120CB Manual de usuario

Nilfisk-Advance

Nilfisk-Advance ATTIX 145-01 Manual de usuario

Manuales populares de Aspiradora de otras marcas

Bissell

Bissell LittleGreen Proheat 1425 Series Manual de usuario

Panasonic

Panasonic MC-YL637S147-AE Manual de usuario

NEFF

NEFF N17XH10 0 Series Manual de usuario

LG A9 Series Manual de usuario

Oreck

Oreck Cordless Captura BK51700 Series Manual de usuario

Kogan

Kogan KAVACROBVWA Manual de usuario

Kränzle

Kränzle VENTOS 50 ID Guía del usuario

EVVO

EVVO Ai35 Manual de usuario

DeWalt

DeWalt DWH200D Manual de usuario

Pontec

Pontec Pondomatic Vacuum Cleaner Manual de usuario

Cleanmaxx

Cleanmaxx PC-P007E Manual de usuario

Exido

Exido 240-114 Manual de usuario

RIDGID

RIDGID WD1685AU0 Manual de usuario

Ezviz

Ezviz RE4P Manual de usuario

STG global

STG global TANVAC HDV3000 Manual de usuario

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Manual de usuario

Factory

Factory M3340 Manual de usuario

Shop-Vac

Shop-Vac VN92 SERIES Manual de usuario