Nexxt Solutions NHE-T100 Manual de usuario
WARRANTY
nexxtsolutions.com/warranty
YEAR
2
Smart Wi-Fi 3-circuit
light switch
English
User guide
Thank you for purchasing the Smart Wi-Fi 3-circuit light
switch from Nexxt Solutions. We are excited for being a
part of making your life easier, safer and bringing peace of
mind inside and outside your home.
Package content
- Smart 3-circuit light switch (1)
- Mounting screws (2)
- Quick setup card (1)
- User guide (1)
Safety information
Precautions
Please read and understand this entire manual before
attempting to assemble, install and operate this smart
electrical xture.
This product requires replacing the existing switch through
a hard-wiring process.
This smart electrical xture requires 110-220-volt AC.
This device has been tested by the manufacturer according
to all international electrical standards. However, every
region has dierent standards and rules for installing
electrical cabling and equipment in a home.
Please check with your local and state laws prior to using
this device.
Improper installation of product may cause electrical injury
to an individual.
Installation of this product must be performed by a
qualied electrician or a certied electrical technician. Do
not attempt to perform installation if you are not familiar
with hardwired electrical connections.
Improper installation can lead to loss of warranty.
Nexxt Solutions assumes no liability for the improper
installation of this product
Product overview
1. Smart switch indicator light:
displays the status of the
wireless connection and
switch.
2. On/o button: use it to
manually toggle the
device on and o
3. Face plate cover
Red
Red
Green
Red
Blinks fast
Solid
Solid
Solid
Ready for pairing
(default mode only)
Indicates that pairing is successful
and that the light switch status is OFF
Indicates that the light switch is ON
No internet connection available
LED light Status Description
Turn power o at the circuit breaker or fuse.
Use only when it’s installed with a residual current device (RCD) or
current leakage protector at home.
WARNING: For safety, this light switch must be
properly grounded.
WARNING: To avoid risk of electric shock or
electrocution, install the light switch away from
any water source.
WARNING: This light switch supports single pole
circuit only. It is not compatible with 3-way
(multi-location control) connection circuit.
WARNING: This is an indoor smart switch that
requires a neutral connection.
WARNING: This device is single band and will
only work with 2.4GHz Wi-Fi routers.
1 2
3
4. Ground wire
5. Neutral wire
6. Live wire
7. Load wire (lights)
Initial inspection
Before installing the electrical xture, ensure that all parts
are included in the package. If any part is missing or
damaged, do not attempt to assemble, install, or operate
this product.
Estimated installation time: about 30 minutes.
Tools that may be required but are not included for
installation
1. Flathead screwdriver
2. Phillips screwdriver
3. Pliers
4. Wire strippers/cutters
5. Circuit tester
6. Work gloves
7. Electrical tape
8. Safety goggles
1 2
3 4
5 6
7 8
4
5
6
7
Step 2
Remove the original switch from the wall box
Identify the Line, Load, Neutral and Ground wires.
Note: If the existing switch has two jacks, you may nd 5
wires or more. Identify the neutral, line, load and ground
wires. This smart switch only needs to use these 4 wires,
since it does not require the connection of additional circuits.
Hardware installation
IMPORTANT
For safety, properly ground the switch
Always follow the code standards when installing
wired connections.
Step 1
Shut power off at the breaker
Find the breaker that controls the circuit for the electrical
box where the smart light switch will be installed. Turn it to
the OFF position.
Place tape over the circuit breaker switch and verify that
power is o.
Note: you can use the circuit tester at this point to verify
that power is cut o.
ON OFF
ON OFF
ON OFF
Neutral
Ground
Load
Line
Switch
North American color code standard:
White is for neutral, black represents the live and load wires,
and the yellow/green cable is for grounding.
Note: a single bare copper wire is also used to represent
the ground wire in existing electrical installations
Europe/Australia color code standard:
Blue is for neutral, brown represents the live and load
wires, and the yellow/green cable is for grounding.
Step 3
Label the wires
Mark the corresponding cables before removing the
existing light switch.
Always follow code standards when installing wired
connections.
Note: All the images are for reference only and therefore,
they must not be used as a standard.
LOAD
LOAD
LINE
GROUNDLINE
LOAD GROUNDLINE
LOAD
LINE
NEUTRAL
There are two mounting methods: Screws can be inserted
at the center or on the sides of the switch, as shown in the
image below.
- Using the correct polarity, match each terminal on the
smart switch with the wires coming from the electrical
box, as shown in the diagrams.
- Attach the wire end to the terminal screw and tighten
until it is fully secured. Repeat this step for each cable.
Note: Follow the wiring conguration below when making
hardware connections:
1) Neutral wire (white) on the electrical box to the neutral
terminal (N) on the smart switch.
2) Ground wire (yellow/green) on the electrical box to the
ground terminal on the smart switch (ground wire
maybe yellow/green or bare copper wire) depending on
existing electrical installation.
3) Line/Live wire (black) on the electrical box to the to line
/live terminal on the smart switch.
4) Load wire (red) on the electrical box to each load
terminal (L1, L2 y L3) on the smart switch.
Mounting
method 1
Mounting
method 2
Step 4
Mount the smart switch
For safety, properly ground the switch
Always follow the code standards when installing
wired connections.
Gently push all the excess wiring into the electrical box.
Note: make sure all the wires are positioned in an
organized manner and away from the edges of the light
switch and the electrical box, to avoid pinching any of the
cables, prior to completing the process.
Proceed to align the smart switch to the base on the
electrical box, so that it is oriented correctly.
Insert the two pre-installed screws on the switch through
mounting holes on the electrical box.
To complete installation, tighten the screws to properly
secure the switch to the wall.
Step 5
Restore power at the breaker
Turn ON the breaker that controls your smart switch to
power it on.
By default, the device will automatically enter into
pairing mode.
ON OFF
ON OFF
ON OFF
Live + Neutral wire conguration
Step 1
Register by email. Fill in the required elds.
Installing the Nexxt Home App
Download the Nexxt Home app on Google Play or Apple
App Store and create a new account.
60 %
9:41 AM
Nexxt Home
Nexxt Solutions Home App
Cancel
GET
Accvent LLC
Login with existing account
Create New Account
SOLUTIONS
Iniciarsesión con cuenta existente
Crear Cuenta Nueva
SOLUTIONS
60 %
9:41 AM
Nexxt Home
Nexxt Solutions Home App
Cancel
INSTALL
Accvent LLC Register by email
United States of America
Email
Get authentication code
Step 3
Create a new password and then select Done.
Set Password
Completed
6-20 characters, including letters and numbers
Step 2
Enter the verication code you received.
Tabla de contenidos
Idiomas:
Otros manuales de Cambiar de Nexxt Solutions
