Newco 767377 Guía

Instruction Sheet PN 128400, 20230822

Technical Service: 1-800-556-3926

WHIPPER MAINTENANCE INSTRUCTIONS

FOR CX TOUCH AND BISTRO SERIES

NEWCO ENTERPRISES INC,

3650 NEW TOWN BLVD SAINT CHARLES, MO 63301

1-800-325-7867

WARNING:

Unp ug machine power and read through a instructions carefu y before

servicing your machine.

DAILY CLEANING

rinse of the whipper should be preformed multiple times a day.

dditionally, whenever the hoppers of the machine are put back into place

after removal, the machine display will prompt for a rinse cycle to be run.

Rinse cycle procedure:

1. Open the door to the brewer and place a cup under the dispense nozzle.

2. Press the RINSE button located to the side of the whipper.

3. Hold the RINSE button until the water dispensed from the nozzle runs clear.

4. Discard the water dispensed during the rinse cycle.

WHIPPER ASSEMBLY PN 767377

Whipper Sea

PN 781566

Whipper Impe er

PN 767197

Whipper Bow

PN 767365

Whipper Cap

PN 767376

Whipper Motor

PN 767195

Whipper Nozz e

PN 767200

Whipper O-Ring

PN 767390

Whipper Base

PN 767196

Inc udes:

O-Ring & Sea

Instruction Sheet PN 128400, 20230822

Technical Service: 1-800-556-3926

WHIPPER MAINTENANCE

Before beginning the physical maintenance of the whipper, it is important to check the

status of the whipper seal cycle count in the machine programming. The whipper seal

needs to be replaced every 5000 cycles.

TO ENTER PROGRAMMING ON THE CX TOUCH AND BISTRO TOUCH

Tap, where circled on the images below, 3 times to enter the Programming Menu.

CAUTION:

Do not press “Whipper Sea Reset” un ess you are rep acing the whipper sea ,

PN 781566.

You must press “Exit Maintenance Mode” then “Exit Programming” before turning off

machine power.

CX Touch Bistro Touch

Bistro Touch

CX Touch

Instruction Sheet PN 128400, 20230822

Technical Service: 1-800-556-3926

TO ENTER PROGRAMMING ON THE BISTRO 10 SERIES

Press and hold where shown above for 7 seconds to enter Programming Mode. Sanitization

mode will show before Programming Mode. Continue to hold appropriate button until

“Select Menu Maintenance” appears.

NOTE:

Recipe names may vary. Instructions shown be ow are for the B10T brewer.

For B10T3

For B10S and B10T

If you are replacing the whipper seal, follow the

directions on the screen to reset the Whipper Seal

Remaining count.

Once Whipper Seal Remaining count has been reset,

scroll to “Select Menu Exit Maintenance”, then scroll to

“Select Menu Exit Program Mode” to save changes.

Screens wi cyc e

Select

or Enter Scroll

Scroll

Down

B10S

B10T3

B10T

Press

Press twice

Press

Instruction Sheet PN 128400, 20230822

Technical Service: 1-800-556-3926

REMOVE THE WHIPPER PARTS FROM THE MACHINE

1. Run a rinse cycle to remove any powder from the

whipper bowl.

2. Turn machine power off and unplug power cord from

wall outlet.

3. Turn elbows of the hoppers upwards.

4. Disconnect dispense nozzle from whipper, and remove

the whipper cap.

5. While holding onto the whipper bowl, turn the knob of the base counterclockwise from

the 6 o’clock position to the 5 o’clock position.

6. Pull whipper bowl away from the machine.

7. Remove the impeller from the motor shaft. The impeller is set securely in place, you may

need a bit of force to remove it.

8. Turn the knob on the base counterclockwise from the 5 o’clock position to the 4 o’clock

position to unlock it from the motor. You may need to wiggle the base to remove it

from the motor shaft.

9. Push the whipper seal out of the whipper base.

CLEAN THE WHIPPER ASSEMBLY

Wash whipper parts with warm soapy water. Wipe down motor shaft with warm soapy

water to remove all old lubrication. Ensure all components are completely dry before

reassembly.

Instruction Sheet PN 128400, 20230822

Technical Service: 1-800-556-3926

REINSTALL THE WHIPPER

1. SET THE WHIPPER SEAL INTO THE WHIPPER BASE

Locate the small raised line on the whipper seal and the whipper base. With the raised

indicators aligned, press the conical side of the whipper seal into the back of the whipper

base. See images below.

WARNING:

If indicator marks are not a igned, whipper sea wi not be fu y seated in p ace

on the whipper base. Whipper sea wi become misshapen, impacting the performance

and ifespan of the entire brewer.

2. LUBRICATE WHIPPER SEAL AND INSTALL WHIPPER BASE ONTO WHIPPER MOTOR SHAFT

Cover the hole in the whipper seal with one finger, fill the seal with food grade lubricant

(PN 900039), then slide the base onto the motor shaft.

Turn the whipper base so that the notch is in the 5 o’clock position.

Instruction Sheet PN 128400, 20230822

Technical Service: 1-800-556-3926

3. INSTALL THE IMPELLER ONTO THE MOTOR SHAFT

Locate the arrow on the impeller, and the flat section on the motor shaft. With the front of

the impeller (as shown below), facing away from the motor, align the arrow indicator with

the flat section of the motor shaft.

CAUTION:

Do NOT force the impe er onto the motor shaft. Improper insta ation may

effect performance.

Slide the impeller onto the motor shaft. click will be heard when the impeller is set into

place.

Not far enough Proper placement Too far

Instruction Sheet PN 128400, 20230822

Technical Service: 1-800-556-3926

4. INSTALL THE WHIPPER BOWL ONTO THE WHIPPER ASSEMBLY

Place whipper bowl into the groove of the whipper base, then turn the knob of the

whipper base clockwise from the 5 o’clock position to the 6 o’clock position.

5. REPLACE CAP AND NOZZLE ONTO THE WHIPPER BOWL

ttach cap and nozzle to the whipper bowl, then connect to appropriate parts in the

brewer.

Tabla de contenidos

Otros manuales de Sistema de elaboración de cerveza de Newco

Newco

Newco 20:1 Manual de usuario

Newco

Newco KB-APF Guía de configuración

Newco

Newco BISTRO TOUCH LARGE CAPACITY Manual de usuario

Newco

Newco CX-3 Manual de usuario

Newco

Newco KB Series Guía de configuración

Newco

Newco AKH-TC-A Manual de usuario

Newco

Newco Bistro Touch BISTRO-TCH Manual de instrucciones

Newco

Newco LITTLE JOE COMPONENT ACCESS Manual de usuario

Newco

Newco KB1 Guía de configuración

Newco

Newco KK airpot Manual de usuario

Newco

Newco LCD-TCH Manual de instrucciones

Newco

Newco DB2A Instrucciones de instalación

Newco

Newco CX-TOUCH Manual de usuario

Newco

Newco CX-TOUCH Manual de usuario

Newco

Newco 805044 Manual de usuario

Manuales populares de Sistema de elaboración de cerveza de otras marcas

CBF-DRINKIT

CBF-DRINKIT Coobra CB25 Manual de usuario

Toddy

Toddy ARTISAN Manual de usuario

Bunn

Bunn GRX Manual de usuario

Keurig

Keurig Vue Manual de usuario

VKI Technologies

VKI Technologies Zuma Brewer Manual de operación

Speidel

Speidel Braumeister PLUS 10 litres Manual de usuario

BrewBuilt

BrewBuilt X2 UNI Manual de usuario

Tribest

Tribest RAW TEA KETTLE Manual de usuario

Sprowt Labs

Sprowt Labs Acro Manual de usuario

KegLand

KegLand Robobrew Manual de usuario

BRAVILOR BONAMAT

BRAVILOR BONAMAT Aurora GTBSH-001 Manual de usuario

Fetco

Fetco CBS-1221 Especificaciones

Curtis

Curtis ThermoPro G4 Series Manual de usuario

Animo

Animo ComBi CB5 Manual de usuario

MoreBeer

MoreBeer BrewSculpture Manual de usuario

Keurig Hot

Keurig Hot Commercial Series Manual de usuario

Keg King

Keg King KEGMASTER XL Manual de usuario

Blichmann Engineering

Blichmann Engineering BrewEasy Compact TC Instrucciones de instalación