New Holland CX Series Guía de referencia

QUICK REFERENCE CARD – NEW HOLLAND CX COMBINES

Form 147074 Rev. E (E27025) Page 1 of 4

A B

1” to 2”

(25 to 50 mm)

DRUM

FLOATED UP

X = 225 mm

(

factor

settin

Combine Initial Settings



Install feeder plate extension (G). Move feeder bottom

shaft to the front hole (Cereal Position) (H).



Adjust the bottom shaft float to 3-1/2” (90mm) at (A).

Adjust the feeder chain tension according to the gauge

on the spring (B).



Ensure feeder house output shaft speed is 575 rpm.



Fully retract header tilt cylinder and lower header until it

slightly contacts the ground. At this point adjust feeder

faceplate angle to align pendulum with rear face of

adapter (if applicable).



Remove all feeder house dust shields, enclosure panels, etc.

873 Adapter Initial Settings



Place adapter leg pin in proper hole for your header

model as follows:

•

963/972/973/974/84C headers in hole (B), (factory set)

with dust shields and hole (A) with dust shields

removed.



Place adapter down stop pin in proper hole for your

header model as follows:

•

973/974/84C headers in hole (2), (factory set).

•

963/972 headers in hole (3).



If mounting adapter to a header, ensure down stop pads are

orientated properly.

•963/972/973 header with dust shields removed and 973

with dust shields on, orientation is correct as shipped (D).

•963/972 with dust shields on, orient pads to position (F).

•974/84C headers, orient pads to position (E).



For 972/973/974/84C - Install skid plate on adapter feed pan so

dim. D = 4-11/32” (110 mm) in Hole B (dust shields installed). For

963 - Slide transition plate forward until feed pan bolts hit front of

slot.

For 972/973/974/84C – Install skid plate on adapter pan so

dim. D = 3-1/2” (90 mm) in Hole A (dust shields removed). For

963 - Slide transition plate rearward until feed pan bolts hit rear

of slot.

•Refer to 873 Operators Manual for adjustment details.



Adjust RTD position to achieve 1” to 2” dimension.

Note: To achieve this feed chain on combine may need to

be fully extended.

Pendulum must line

up with rear face of

adapter frame.

QUICK REFERENCE CARD – NEW HOLLAND CX COMBINES

Form 147074 Rev. E (E27025) Page 2 of 4

873 Adapter Initial Settings

(continued)

Set the center link between the header and

adapter to 19-1/4” (490 mm) length (pin to

pin).

Set the float to specs given on pages 3 & 4.

Set the draper speed flow control so number

“4” is at the 12 o’clock position.

Header Initial Settings

See page 4 for 963 Header

For 973/974/84C Model Headers: Set the

center delivery opening to 55.5” (1410 mm).

Position the decks so there is equal

overlap of adapter feed draper each

side.

Align the vertical edge of the rear deflectors

on the feed pan just inside the edge of the

feeder house opening to ensure smooth

crop flow.

Re-check skid plate clearance (set during

873 initial settings) with adapter inserted in

header. (see appropriate dimensions below)

Refer to 873 Operator’s Manual for further

details.

Gauge wheels are intended to help float the

header when cutting off the ground. For

such applications set gauge wheels in the

Short – Tall setting depending on cut height.

Note: When cutting on the ground place

gauge wheels in the storage position.

Pickup Reel Initial Settings



See page 4 for 963 Header



Install bolt (C) through the cam arm with head

inboard and torque to 120 ft. lbs. (162 N·m.)



Adjust the finger pitch to position 5.



Set the fore/aft position to between 4and 5on

the gauge decal at left reel support arms.



Reel finger to sickle guard minimum clearance with

reel fully lowered is 5/8” (15mm), measured at

both ends of the cutterbar for 973 headers. For

974/84C headers, flex to full frown when

checking clearance at hinge points.



Recommended reel speed is 10% above ground

speed.

55.5”

(

1410 mm

)

973/974/84C

QUICK REFERENCE CARD – NEW HOLLAND CX COMBINES

Form 147074 Rev. E (E27025) Page 3 of 4

973/2052 & 974/2062/84C Initial Set-up

Rice Soybeans

Average Cereal Crops

Normal Cutting Tough Cutting Dry Conditions Wet

Conditions

Sickle- Check daily that guards are

aligned. Clearance from hold down

to sickle 0.020” (0.5mm)

- - -

2100 reel Fore/Aft- 4 or 5 on decal

Finger Pitch Adjustment- Slot 5

Reel Clearance- 5/8” (15mm) for

973/2052 headers and at hinge

points for 974/2062/84C headers in

full frown. Refer to 973/974

Operator’s Manual.

Speed- +10 % ground speed.

Slot 7

½” (13mm)

Slot 7

½” (13mm)

Draper Speed- Dial position “4”.

Draper opening- 55” (1410 mm)

Reduce opening if side drapers are

back feeding.

Position 3 or 4

50.6” (1285 mm)

Guard Angle- center link 19-¼”

(490 mm) length (pin to pin).

Poly Skids- Optional on 973/2052

Yes

Center link fully

retracted.

Yes

Gauge Wheels (if equipped)-

Most cereals require “medium”

stubble height setting

Note: Gauge wheels should be in

storage position for on the ground

cutting applications.

Not Applicable Not Applicable Storage Storage

Float- Adjust float to achieve 0” gap

at downstop pad. (Refer to 873

Operator’s Manual)

½” gap ½” gap ½” gap ½” gap

QUICK REFERENCE CARD – NEW HOLLAND CX COMBINES

Form 147074 Rev. E (E27025) Page 4 of 4

963/2042 Initial Set-up. Field Peas Soybeans

Average Cereal Crops Dry Conditions Wet Condition Dry Conditions Wet Condition

Sickle-Check daily that guards are

aligned. Clearance from hold down

to sickle 0.020” (0.5mm) - - - -

2000B Reel Fore/ Aft-5

hole/frt.

Cam Arm-Y

Range Slot- P

Finger Pitch- L or M

Reel Clearance- 2” (50 mm)

Speed- +10% of ground speed

from front

2” (50mm)

from front.

2” (50mm)

from front

2” (50mm)

from front.

2” (50mm)

Draper Speed- Dial position “4”.

Draper opening- 53.5” (1360 mm)

Guard Angle- 1.0” (25mm) of

threads showing on center link.

Poly Skids- None

Yes

Center link fully

retracted.

Yes

Gauge Wheels (if equipped)-

Most cereals require “position 2”

stubble height setting.

Note: Gauge wheels should be in

storage position for on the ground

cutting applications.

Storage Storage Storage Storage

Float- Adjust float to achieve 0” gap

at downstop pad. (Refer to 873

Operator’s Manual)

½” gap ½” gap ½” gap ½” gap

53.5

(1360 mm)

963/2042

Storage position

for on ground

application

Otros manuales de Maquinaria agrícola de New Holland

New Holland

New Holland BR6080 Manual de usuario

New Holland

New Holland P2350 Manual de usuario

New Holland

New Holland MegaCutter 512 Manual de usuario

New Holland

New Holland 130 Manual de usuario

New Holland

New Holland Haybine 499 Manual de usuario

New Holland

New Holland AutoCommand T7.275 Manual de usuario

New Holland

New Holland T7 AutoCommand Instrucciones de montaje

New Holland

New Holland Guardian SP.240F Manual de usuario

New Holland

New Holland T8010 Manual de usuario

New Holland

New Holland 330GM Manual de usuario

New Holland

New Holland CornMaster 9208-22 Manual de usuario

New Holland

New Holland BB1290 Manual de usuario

New Holland

New Holland 16LA Manual de usuario

New Holland

New Holland TC5040 Manual de usuario

New Holland

New Holland H9870 Manual de usuario

New Holland

New Holland T7.175 Manual de usuario

New Holland

New Holland FR480 Forage Cruiser Manual de usuario

New Holland

New Holland CR6090 Tier 4a Manual de usuario

New Holland

New Holland FR480 Forage Cruiser Manual de usuario

New Holland

New Holland 9040L Manual de usuario

New Holland

New Holland 140TL Manual de usuario

New Holland

New Holland SF550 Instrucciones de funcionamiento

New Holland

New Holland TH Telehandler Guía del usuario

New Holland

New Holland TT45A Instrucciones de funcionamiento

Manuales populares de Maquinaria agrícola de otras marcas

GSi

GSi PNEG-2314 Manual de usuario

Checchi & Magli

Checchi & Magli TEXDRIVE Manual de usuario

Amazone

Amazone Cenius 4003-2TX Manual de usuario

MASSEY FERGUSON

MASSEY FERGUSON MF 9313S Manual de usuario

Cima

Cima BLITZ Instrucciones de funcionamiento y mantenimiento

Amazone

Amazone CombiDisc 3000 Instrucciones de instalación

HE-VA

HE-VA Disc-Roller XL Contour Manual de usuario

AGT

AGT AGT-SSFM Manual de usuario

Milestone

Milestone 72-84 Manual de usuario

KUHN

KUHN Hector 3000 Manual de usuario

Krone

Krone X-Disc 6200 Manual de usuario

Eliet

Eliet DZC450 Manual de usuario

Taarup

Taarup BIO+ B4000 Manual de usuario

Garland

Garland SHAKER 310 DPG Manual de usuario

stable comfort

stable comfort StableWall System Manual de usuario

Raven

Raven AccuBoom Manual de usuario

International

International 710 Manual de usuario

Ashland

Ashland HDW-3217-14 Manual de usuario