NeuraLabel 550e Manual de usuario

Page 1

www.neuralabel.com

NeuraLabel 550e

Setup and Quick Start Guide for use

with Fanfold GHS Drum Labels

August 2020

Page 2

www.neuralabel.com

Table of Contents

•Unpacking: Part Identification

•Step 1: Printer Setup

•Step 2: Feeder Setup

•Step 3: Power Up the System

•Step 4: Load Media

•Step 5: Print and Calibrate

•Printing Tips & Troubleshooting

•Firmware and Contact Information

Page 3

www.neuralabel.com

Remove printer from box. Lift from box with two people.

Remove feeder from box and set aside.

Unpacking the Printer and Feeder

Power Cord

Starter Toner

Continuous Feeder Attachment

Print Engine

Page 4

www.neuralabel.com

Step 1: Printer Setup

Plug in the power cord to the back of the printer and directly to a wall outlet.

Door B

Set up the printer on a sturdy table with plenty of room for fanfold media.

Plug in network or USB to the back of the printer.

Open printer side door B. Unpack starter toner and place in printer. Close printer door.

Page 5

www.neuralabel.com

Step 2: Feeder Setup

Place the Continuous Feeder Attachment onto the front of the printer. It slides on to the

mounting bar on the printer tray. Make sure it attaches squarely to the printer.

Attach the feeder round “barrel” connector to the round connector at the back

of the printer just above the printer’s power port.

Continuous Feeder Attachment

Printer power must be OFF when attaching or removing continuous feeder attachment.

Feeder Barrel Connector

NOTE: The Feeder is powered by the printer.

Page 6

www.neuralabel.com Page 6

Turn on the printer and feeder

Press the power button near the printer operator panel. The printer and the attached

feeder will boot up. This will take about one minute.

•The printer operator panel displays the NeuraLabel logo and then the home screen.

•The feeder LED flashes its version number.

•The feeder executes a boot up diagnostic sequence which exercises all the motors.

•The feeder LED turns white if configured for marks or green if configured for gaps.

The printer is powered OFF by pressing the power button for at least 5 seconds.

Keep the printer ON for the next steps.

Step 3: Power up the System

NOTE: Fanfold media uses marks. There is a switch at the bottom of the CFA that sets it to marks

or gaps. Check this switch if needed.

Page 7

www.neuralabel.com Page 7

Step 4: Load Media

Printer must be powered ON during this step.

Place fanfold media stack near the printer such that black marks are face up and larger

registration mark is on the left side.

unlocked locked

Check to make sure the media is loaded in straight and flat.

unlocked

Load the leading edge of media into the feeder. Push media in until the feeder

automatically loads it.

Media should be far enough away from the feeder so

that it easily unfolds.

Media may be place on a surface lower than the

printer, such as a table or even the floor.

Page 8

www.neuralabel.com

Step 5: Print and Calibrate

Send a sample print job.

•Make sure the printed form matches your media size.

•Initial Job is about 20 labels for auto-calibration.

As media exits the printer, it will self fold at the printer exit. (Letter and Legal size.)

Printer is ON

Media is loaded correctly into the feeder and is straight

Stacking area is clear

The 550e auto-calibrates; that is, it fits the form to a specific media. It must be given

an initial label run for the procedure to correctly take place.

Page 9

www.neuralabel.com

Contact Information

•www.neuralabel.com

•support@neuralabel.com

•orders@neuralabel.com

NeuraLabel 550e Engine and Feeder Firmware

Engine and Feeder Version is accessible via the printer operator panel or web server.

Settings->Reports->Device->Device Information

Engine and Feeder are updated through the printer’s web server

Settings->Device->Update Firmware

All available Firmware Updates are found at NeuraLabel.com/setup/550e

Updating Your Devices

Otros manuales para 550e

Tabla de contenidos

Otros manuales de Etiquetadora de NeuraLabel

NeuraLabel

NeuraLabel 600e Manual de usuario

NeuraLabel

NeuraLabel 600e Guía de configuración

NeuraLabel

NeuraLabel Sirius Manual de usuario

NeuraLabel

NeuraLabel Sirius 4 Manual de usuario

NeuraLabel

NeuraLabel 550e Manual de usuario

NeuraLabel

NeuraLabel 500e Manual de usuario

NeuraLabel

NeuraLabel 300x NoTouch Manual de usuario

NeuraLabel

NeuraLabel 550e Manual del operador

NeuraLabel

NeuraLabel Sprint Manual de usuario

NeuraLabel

NeuraLabel Sprint Manual de usuario

Manuales populares de Etiquetadora de otras marcas

Brother

Brother P-Touch 2420PC Manual de usuario

newell

newell Dymo LabelManager 210D Manual de usuario

Brother

Brother TD-4000 Manual de usuario

U-Line

U-Line BROTHER H-8754 Manual de usuario

Tharo Systems

Tharo Systems H-435+ Manual de usuario

Brother

Brother E300 Manual de usuario

Godex

Godex RT700 SERIES Manual de usuario

ID Technology

ID Technology 252 Manual de usuario

Labelmate

Labelmate MC-11 Manual de usuario

CAB

CAB XD4M/300 Manual de usuario

Avery Dennison

Avery Dennison Pathfinder 6057 Manual de servicio

Brother

Brother P-touch PT-9700PC Manual de usuario

TSC

TSC PEX1000 Series Manual de usuario

Adkins

Adkins Label Master Manual de usuario

Epson

Epson LabelWorks LW-400 Manual de usuario

Primera

Primera 510212 Manual de usuario

Brady

Brady BradyPrinter S3100 Manual de usuario

DuraLabel

DuraLabel LabPRO Manual de usuario