Netvox RA0716 Manual de usuario

Model：RA0716_R72616_RA0716Y

Wireless PM2.5/Temperature/Humidity Sensor

Wireless PM2.5 / Temperature /

Humidity Sensor

User Manual

This document contains proprietary technical information which is the property of

NETVOX Technology. It shall be maintained in strict confidence and shall not be

disclosed to other parties, in whole or in part, without written permission of NETVOX

Technology. The specifications are subject to change without prior notice.

Table of Content

1. Introduction.................................................................................................................2

2.Appearance..................................................................................................................3

3. Main Features .............................................................................................................4

4. Set up Instruction........................................................................................................5

5. Data Report.................................................................................................................7

6. Installation ..................................................................................................................9

7. Important Maintenance Instruction ..........................................................................11

1. Introduction

RA0716_R72616_RA0716Y is a ClassA type device based on the LoRaWAN open protocol of

Netvox and is compatible with the LoRaWAN protocol.

RA0716_R72616_RA0716Y can be connected to a variety of sensors. A variety of sensor

combinations are required.

As detectors for PM2.5, temperature and humidity, the values collected by the sensor are reported to

the corresponding gateway.

LoRa Wireless Technology:

LoRa is a wireless communication technology dedicated to long distance and low power

consumption. Compared with other communication methods, LoRa spread spectrum modulation

method greatly increases to expand the communication distance. Widely used in long-distance,

low-data wireless communications. For example, automatic meter reading, building automation

equipment, wireless security systems, industrial monitoring. Main features include small size, low

power consumption, transmission distance, anti-interference ability and so on.

LoRaWAN:

LoRaWAN uses LoRa technology to define end-to-end standard specifications to ensure

interoperability between devices and gateways from different manufacturers.

Temperature & Humidity sensor

Indicator

DC in

PM2.5 sensor

Button

Waterproof cover

Built-in battery pack

Built-in PM2.5, Temperature & Humidity

Solar panel

2. Appearance

Figure 1 RA0716

Figure 2 R72616

Built-in PM2.5, Temperature & Humidity

Power Cable

Figure 3 RA0716Y

3. Main Features

Compatible with LoRaWAN

RA0716 and RA0716Y powered by DC 12V adapters

R72616 powers solar and rechargeable lithium batteries

Easy set up and installation

PM2.5, Temperature and Humidity detection

Adopt SX1276 wireless communication module

4. Set up Instruction

On/Off

Power on RA0716 and RA0716Y are connected to the DC 12V adapter for power-

on;

R72616 applies solar and rechargeable lithium batteries.

Turn on

Power on to turn on.

Power off Remove power

Note:

1. Engineering test modes require the program engineering test software.

2. On/off interval is suggested to be about 10 seconds to avoid the

interference of capacitor inductance and other energy storage

components.

Network Joining

Never joined the network

(Or at factory setting )

Turn on the device to search the network.

The green indicator stays on for 5 seconds: success

The green indicator remains off: fail

Had joined the network

(Not at factory setting.)

Turn on the device to search the previous network.

The green indicator stays on for 5 seconds: success

The green indicator remains off: fail

Fail to join the network

(when the device is on)

First two mins: wake up every 15 seconds to send request.

After two mins: enter sleeping mode and wake up every 15 minutes to send

request.

Note: Suggest to remove batteries if the device is not used to save power.

Suggest to check the device verification information on the gateway

or consult your platform server provider.

Function Key

Press and hold for 5

seconds

Restore to factory setting

The green indicator flashes for 20 times: success

The green indicator remains off: fail

Press once

The device is in the network: the green indicator flashes once and the

device sends a data report

The device is not in the network: green indicator remains off

Low Voltage Threshold

Low Voltage Threshold 10.5 V (R72616)

Restore to Factory Setting

Description

RA0716_R72616_RA0716Y has the power-down save network information memory

function.

This feature is turned off by default, that is, it will be re-joined every time it is powered

back on.

It can be turned on by the ResumeNetOnOff command.

At this time, each time the power is rewritten, the last networking information will be

recorded (including saving the network address information assigned to it, etc., if users

want to join a new network, they need to perform a factory reset operation before that.),

will not re-join.

Operation 1. Press and hold the function key for 5 seconds to release and the LED flashes 20 times.

2. The device automatically restarts to start re-join.

5. Data Report

The device will immediately send a version packet report along with an uplink packet including

temperature, humidity, voltage and PM2.5 value.

The device sends data in the default configuration before any configuration is done.

ReportMaxTime:

RA0716 / RA0716Y is 180s

R72616 is 900s (subject to factory settings)

Value must be greater than ReportMinTime

≧

ReportType count *ReportMinTime + 10 ,units: seconds

ReportMinTime: 30s;

ReportChange: 0;

ReportType count = 1;

Note:

(1) The device report interval will be programmed base on the default firmware which may vary.

(2) The interval between two reports must be the Maxtime

(3) ReportChange is not supported by RA0716_R72616_RA0716Y (Invalid configuration)

(4) Report cycle will be based on ReportMaxTime period when sending data packet (beginning to

the end of the first data as a period).

(5) Data packet: temperature,humidity,voltage and PM2.5

(6) It would take about 35 seconds for the PM2.5 sensor to sample and process the collected PM2.5

value after being powered

(7) The device also supports Cayenne's TxPeriod cycle configuration instructions. Therefore, the

device can also perform a report according to the cycle time of the TxPeriod value; and

whether the report period is ReportMaxTime or TxPeriod will be depending on which cycle

time is configured last time;

(8) It would take about 35 seconds for the PM2.5 sensor to sample and process the collected PM2.5

value if you were to manually trigger the device by pressing the button, please be patient.

The device reported data parsing please refer to

Netvox LoraWAN Application Command document and Netvox Lora Command Resolver

http://www.netvox.com.cn:8888/page/index

Report Configuration

(1) Configure RA0716 device parameters MinTime = 30s, MaxTime = 120s (120>30*1+10)

Downlink: 0135001E00780000000000

Device returns:

8135000000000000000000 (configuration is successful)

8135010000000000000000 (configuration failed)

(2) Read RA0716 device parameters

Downlink: 0235000000000000000000

Device returns:

8235001E00780000000000 (device current parameter)

Description Device CmdID DeviceType NetvoxPayLoadData

Config

ReportReq

RA0716

R72616

RA0716Y

0x01

0x35

0x36

0x37

MinTime

(2bytes Unit:s)

MaxTime

(2bytes Unit:s)

Reserved

(5Bytes,Fixed 0x00)

Config

ReportRsp 0x81 Status

(0x00_success)

Reserved

(8Bytes,Fixed 0x00)

Read Config

ReportReq 0x02 Reserved

(9Bytes,Fixed 0x00)

ReadConfig

ReportRsp 0x82 MinTime

(2bytes Unit:s)

MaxTime

(2bytes Unit:s)

Reserved

(5Bytes,Fixed 0x00)

6. Installation

1. The RA0716 does not have a waterproof function. After the network joining is completed, please

place it indoor.

2. The R72616 product is waterproof. After the network-joining is completed, please leave it

outdoors.

(1) In the position to be installed, loosen the U-shaped screw of the bottom of the R72616 and the

mating washer nut, and fix the U-shaped screw through the appropriate size cylinder on the

R72616 fixed strut piece. Install the washer nut in order, lock the nut till R72616 body is stable

and does not shake.

(2) At the upper side of the fixed position of R72616, loosen the two U-shaped screws on the side of

the solar panel and the mating washer nut.

Fix the U-shaped screw through the appropriate size cylinder on the main bracket of the solar

panel, and install the gasket in sequence. Lock nut till the solar panel is stable and does not shake.

(3) Adjust the angle of the solar panel. After the adjustment is completed, lock the nut.

(4) Connect the R72616 top waterproof cable to the solar panel wiring and lock it tight.

(5) R72616 has a battery pack inside, users can buy and install rechargeable 18650 lithium battery, a

total of 3 sections, a single rechargeable lithium \ battery voltage 3.7V, capacity recommended

5000mah, the installation of rechargeable lithium battery steps are as follows:

1: Remove the four screws around battery cover

2: Insert three 18650 lithium batteries. (Please make sure the battery positive and negative)

3: Press the activation button on the battery pack for the first time.

4: After activation, close the battery cover and lock the screws around battery cover.

activation button

Otros manuales para RA0716

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accesorios de netvox

netvox

netvox R718LB2 Manual de usuario

netvox

netvox R718DB Manual de usuario

netvox

netvox R718PB13 Manual de usuario

netvox

netvox R718N3 Manual de usuario

netvox

netvox R311CA Manual de usuario

netvox

netvox R718VA Manual de usuario

netvox

netvox RB11E Manual de usuario

netvox

netvox R311B Manual de usuario

netvox

netvox R718PG-AS923 Manual de usuario

netvox

netvox R718PB13 Manual de usuario

netvox

netvox R718F Manual de usuario

netvox

netvox ZB11A1 Manual de usuario

netvox

netvox R311FA Manual de usuario

netvox

netvox R718PA5 Manual de usuario

netvox

netvox R72616A Manual de usuario

netvox

netvox R718PA7 Manual de usuario

netvox

netvox Contact Sensor Series Manual de usuario

netvox

netvox RA0711 Manual de usuario

netvox

netvox RA0723 Manual de usuario

netvox

netvox R718EB Manual de usuario

netvox

netvox R718F2 Manual de usuario

netvox

netvox R311FA Manual de usuario

netvox

netvox R718DA Manual de usuario

netvox

netvox Z808B Manual de usuario

Manuales populares de Accesorios de otras marcas

Hillco

Hillco 2810 Manual de usuario

Siemens

Siemens QSA2700D Manual del operador

Contours

Contours ZY024 Manual de usuario

Saivod

Saivod VS621 Manual de usuario

Virtuox

Virtuox VirtuCLEAN 2.0 Manual de usuario

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manual de usuario

Z-Wave

Z-Wave HSD-200Z Manual de usuario

turck

turck FMX-IM-2UPLI63FX Manual de usuario

Decagon Devices

Decagon Devices 10HS Manual de usuario

UPPAbaby

UPPAbaby Cup Holder Manual de usuario

Elko

Elko SmartSensor Leakage Wireless Manual de usuario

Grizzly

Grizzly H8371 Manual de usuario

Panasonic

Panasonic HG-T Series Manual de usuario

IFM Electronic

IFM Electronic Efector 250 Series Guía de referencia

DigiDesign

DigiDesign 888/24 I/O Manual de usuario

PROZIS

PROZIS QUAY Manual de usuario

patagonia

patagonia PSI Vest Manual de usuario

SFC Energy

SFC Energy EFOY GO! Manual de usuario

netvox RA0716 Manual de usuario

Manuales populares de Accesorios de otras marcas