NETGEAR STM150 - ProSecure Web And Email Threat Management... Manual de usuario

Installation Guide

ProSecure™ Web/Email Security Threat Management Appliance STM150

Start Here

Follow these instructions for

setting up a gateway

configuration where a single

STM150 is installed between

your firewall and the LAN core

switch.

After completing these

installation steps, your network

will resemble this illustration.

For server group or segmented

LAN configurations, refer to the

Reference Manual.

You can download the

Reference Manual from the documentation link in the Web Support page of the product

user interface or from the ProSecure site at:

http://prosecure.netgear.com/resources/document-library.php

Before you begin, ensure you have the IP configuration parameters of your network

(available reserved IP address, subnet range, gateway, and DNS addresses).

Estimated completion time: 25 minutes.

Verify the Package Contents

Unpack the box and verify the contents:

• ProSecure Web/Email Security Threat Management Appliance STM150

• Depending on the model purchased, license registration card

• Rubber feet (4) with adhesive backing

• Rack mount brackets hardware

• Power cord

• Straight through Category 5 Ethernet Cable

• Installation Guide

Familiarize Yourself with the STM150

Take note of the connectors, status lights, and controls on the front and back of the unit.

1. Power. Green power LED.

2. Test.Amber test LED.

3. NETGEAR Diagnostic USB ports.

4. UPLINK Gigabit Ethernet port.

5. Four DOWNLINK Gigabit Ethernet ports.

6. Serial console port.

7. Kensington lock connector to prevent unauthorized removal of the unit.

8. Power button - press once for normal shut down; press and hold for forced shutdown.

9. Recessed pin-push back to factory default reset button.

10. Power connector.

Connect the STM150 to Your Network

1. Power on the STM150 by plugging in the power cable and connecting it to the power

connector on the rear of the unit. Verify the following:

•Power. The power LED (1) should turn solid green. If it does not turn solid green,

see the Troubleshooting section in the Reference Manual.

•Test. Initially, the amber test LED (2) will be lit for approximately 2 minutes. If it

is still on after 2 minutes, see the Troubleshooting Tips.

2. Connect the UPLINK Ethernet port (4) to your gateway firewall.

3. Use the Ethernet port LEDs to verify the status and speed of the connection,

according to the legend printed on the front of the unit.

4. Connect a computer to the STM150

a. The STM150 factory default IP address is 192.168.1.201. Configure a computer

with a static IP address such as 192.168.1.111.

b. Connect this computer to one of the DOWNLINK Ethernet ports (5).

c. Use the Ethernet port LEDs to verify the status and speed of the connection,

according to the legend printed on the front of the unit.

Configure the STM150 Network Settings

1. Log in to the STM150

a. Use a browser to connect to

https://192.168.1.201.

b. When prompted, enter admin for

the User Name and password for the Password.

c. Click Login. You are now connected. The default Status

screen displays.

The Web Support tab on the main menu contains links to

the online ProSecure STM150 product documentation and support

knowledgebase.

Note: After 5 minutes of inactivity (the default login time-out), you are

automatically logged out.

2. Configure the Network Settings

a. Select Global Settings > Network

Settings. The Network Settings tab

displays.

b. Fill in the settings, according to the

configuration requirements of your

network. Be sure to record the IP

address you assign the STM150; you will need it in the future when you log in to

this unit. For now, ignore the speed and MTU settings.

Note: If your network uses DHCP, be sure to reserve this IP address for the

STM150 in your DHCP server or gateway firewall.

https://192.168.1.201

December 2009

This symbol was placed in accordance with the European Union Directive 2002/96 on the Waste

Electrical and Electronic Equipment (the WEEE Directive). If disposed of within the European Union,

this product should be treated and recycled in accordance with the laws of your jurisdiction

implementing the WEEE Directive.

of NETGEAR, Inc. in the United States and/or other countries. Other brand and product names are trademarks or

registered trademarks of their respective holders. Information is subject to change without notice.

c. Click Apply to save your changes.

The STM150 will reboot. Your computer will loose its connection to the unit if

its IP address is now on a different subnet than the STM150. If so, re-configure

the computer to match the settings of your network.

Activate the Service Licenses

Note: Activating the service licenses initiates their term of use. Activate the licenses only

when you are ready to start using this unit.

1. If your STM150 included a

license key card, refer to it

Be sure to store the license key

card in a secure location. Not

only will you need these keys to

activate your product during the

initial setup, but also to

reactivate the licenses if you ever

have to reset the unit back to its factory defaults.

If you did not get a license key card, have your license keys available.

2. Register the licenses.

Note: Be sure the unit has

Internet access before

registering the licenses.

a. Log in to the unit.

b. Select Support >

Registration to display the

Registration tab.

c. Enter the first registration

key and customer information. Then, click Register.

d. Repeat this step for the remaining keys. The STM150 will activate the licenses

and register the unit with the ProSecure support server.

Run the Setup Wizard

1. Start the Setup Wizard.

Select Global Settings > Setup

Wizard to start the wizard.

For guidance on how to fill in the

wizard screens, refer to the online

help or Reference Manual.

2. Configure the Web/Email Threat

Management settings.

Follow the wizard prompts to

configure these settings:

• Network settings - update these as needed.

• Define internal domains for scan policies on various types of traffic.

• Set the system time (NTP server) and time zone.

• Enable scanning of network protocols.

• Define default scan actions when the unit detects threats.

• Define scan exceptions like the maximum file size.

• Specify the notification server and notices for email notices.

• Configure web interface security (inactivity time-out and ACL members).

• Specify how firmware updates will be made.

• Enter HTTP proxy settings.

• Select web categories to block.

Online Documentation and Support

Select Support > Documentation to

view the STM150 reference manual.

Select Support > Knowledge Base to

view the STM150 support page,

which includes this document and the

reference manual. Going to

http://www.netgear.com/support and

selecting STM150 takes you to the

same page.

Technical Support

Thank you for selecting ProSecure products.

After configuring your Web/Email Security Threat Management Appliance , locate the

serial number on the bottom label of your product and use it to register your product at

http://www.netgear.com/register. Registration on the web site is required before you can

use our telephone support service.

The phone numbers for worldwide regional customer support centers are on the Warranty

and Support Information card that came with your product.

Go to http://prosecure.netgear.com/support for product updates and web support.

Otros manuales para STM150 - ProSecure Web And Email Threat Management...

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Hardware de red de NETGEAR

NETGEAR

NETGEAR ProSafe UTM9S Manual de usuario

NETGEAR

NETGEAR Sprint Spark Hoja de especificaciones

NETGEAR

NETGEAR SRX5308 - ProSafe® Quad WAN Gigabit SSL VPN... Manual de usuario

NETGEAR

NETGEAR Sb 104 Manual de usuario

NETGEAR

NETGEAR AGM722F Manual de usuario

NETGEAR

NETGEAR XAVBI 301 Manual de usuario

NETGEAR

NETGEAR ProSafe UTM9S Manual de usuario

NETGEAR

NETGEAR EX6150 AC1200 Manual de usuario

NETGEAR

NETGEAR MR60 Manual de usuario

NETGEAR

NETGEAR WN1000RP Manual de usuario

NETGEAR

NETGEAR ReadyDATA 5200 Manual de usuario

NETGEAR

NETGEAR Nighthawk Mesh WiFi 6 System Manual de usuario

NETGEAR

NETGEAR Powerline AV 200 Manual de usuario

NETGEAR

NETGEAR RNDP600E - ReadyNAS Pro Pioneer Edition NAS... Manual de usuario

NETGEAR

NETGEAR RND4000 - ReadyNAS NV+ NAS Server Guía del usuario

NETGEAR

NETGEAR RNDP6310 - ReadyNAS Pro NAS Server Manual de usuario

NETGEAR

NETGEAR Orbi Pro WiFi 6 Mini router Manual de usuario

NETGEAR

NETGEAR UTM5 - ProSecure Unified Threat Management... Manual de usuario

NETGEAR

NETGEAR FB 104 Manual de usuario

NETGEAR

NETGEAR M5300 Series Manual de instrucciones

NETGEAR

NETGEAR ProSafe AX742 Manual de usuario

NETGEAR

NETGEAR UTM10 - ProSecure Unified Threat Management... Instrucciones de instalación y funcionamiento

NETGEAR

NETGEAR UTM25-100NAS - Prosecure Utm Appliance 25U No Sub... Manual de usuario

NETGEAR

NETGEAR AXM752 - ProSafe XFP Transceiver Module Manual de usuario

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario