NETGEAR MBM621 - 3G HSDPA Ethernet Modem Manual de usuario

)NSTALLATION'UIDE

Mobile Broadband Modem MBM621

Requirements

Before installation, make sure that these requirements are met:

• You must have an account for wireless broadband service, and you must be located in

an area with wireless broadband coverage. Check with your Internet Service Provider

(ISP) if you are not sure.

• You need an activated SIM card from your ISP.

• You must have a computer with an available Ethernet port to connect to the Mobile

Broadband Modem.

• Your computer must be configured with DHCP.

• For installation with a router, first install the Mobile Broadband Modem to work with

a computer. Then follow the instructions that came with the router to connect the

router to the modem.

Installation

Follow these instructions to install the modem.

Install the SIM Card, and Connect the Modem to a

Computer

To connect the Mobile Broadband Modem:

1. Turn off your computer.

2. Insert your activated SIM card into the

slot on the rear of the modem.

3. Attach the cover to protect the SIM

card.

Power On the Modem and Computer

Follow these steps:

1. Plug in the power adapter to your

modem.

2. Verify the following:

• The Power light is lit after

you apply power to the modem.

• The Status light comes on

briefly and then goes off.

• The Internet light comes on.

For more information about LEDs, see

“Understanding the LEDs” on the other side of this document.

3. Attach the feet to the modem, and adjust

the antenna so that it is pointed up at a 90

degree angle for best performance.

4. Turn on your computer, let the operating

system boot up, and log in as needed.

The Ethernet (LAN) light on the

modem lights up.

4. Connect the Ethernet cable that came with your

modem to an Ethernet local area network (LAN)

port on your computer. and to the Ethernet port on

the modem.

1. On your computer, open a Web

browser.

2. Type http://modemlogin.net

in the address field of your browser.

3. Enter admin for the user name, and

password for the password, both in

lower case letters.

The Broadband Settings screen opens.

• If your SIM card is programmed by your ISP

with broadband settings, the settings are

displayed on this screen. Click Connect. The

modem connects to the Internet.

• If your SIM card is not programmed then you

must enter the settings, click Apply to save

the settings, and then click Connect. The

settings are explained below:

–User Name. The user name for the

broadband Internet service account.

This is not admin, which is the modem user name.

–Password. The password for the broadband Internet service account.

–PIN Code. The PIN code for the SIM card.

–APN. The ISP network name.

–PDP Type. The type of packet data protocol.

–Connection check boxes. These settings determine whether or not the

modem connects at startup or reconnects when an Internet connection is

lost.

If you are not sure what to enter for these settings, contact your ISP.

November, 2007

This symbol was placed in accordance with the European Union Directive 2002/96 on

the Waste Electrical and Electronic Equipment (the WEEE Directive). If disposed of

within the European Union, this product should be treated and recycled in accordance

with the laws of your jurisdiction implementing the WEEE Directive.

of NETGEAR, Inc. in the United States and/or other countries. Other brand and product names are trademarks or

registered trademarks of their respective holders. Information is subject to change without notice.

Understanding the LEDs

You can use the LEDs to verify how the modem is working or to identify the source of a

problem.

LED Activity

Power • Green: The modem is on and operating normally.

•Off: Power is not supplied to the modem.

Status • Amber: Power-on self-test is in progress. If this light remains

on it indicates that the test failed.

• Off: Normal operation after power-on self-test.

Internet • Blue: Excellent signal.

•Green: Good signal.

•Amber: Weak signal.

•Blinking: Data is being transmitted or received on the Internet

port.

•Off: No Internet connection. This can occur if you are outside of

the coverage area, if the SIM card is not installed in the

modem, or if the SIM card has not been activated.

Ethernet • Green: The Ethernet port is operating at 100 Mbps.

•Amber: The Ethernet port is operating at 10 Mbps.

•Blinking: Data is being transmitted or received on the Ethernet

port.

•Off: No device is connected to the Ethernet port.

Returning to Factory Default Settings

You can use the reset button on the back of the modem to return the modem to its factory

default settings. This is useful if you changed the password and do not remember what it

is. You will lose all settings that you entered, and the modem will return to the factory

default settings shown in the following table:

Factory Default Settings

http://www.modemlogin.com

User name (case sensitive) admin

sensitive) password

WAN MAC address Use default hardware address

WAN MTU size 1500

Local area network (LAN) IP 192.168.1.1

Subnet mask 255.255.255.0

RIP direction None

RIP version Disabled

RIP authentication None

DHCP server Enabled

DHCP starting IP address 192.168.1.2

DHCP ending IP address 192.168.1.254

DMZ Enabled or disabled

Time zone GMT

Daylight saving time Disabled

SNMP Disabled

To reset the modem, press and hold down the reset button for 5 seconds.

Technical Support

Contact your Internet Service Provider for technical support. Register your product at

http://www.NETGEAR.com/register, so that you can check for firmware updates for the

modem.

Otros manuales para MBM621 - 3G HSDPA Ethernet Modem

Tabla de contenidos

Otros manuales de Módem de NETGEAR

NETGEAR

NETGEAR CG814M Manual de usuario

NETGEAR

NETGEAR CM500 Manual de usuario

NETGEAR

NETGEAR C3700v2 Manual de usuario

NETGEAR

NETGEAR CG814WG V3 Manual de usuario

NETGEAR

NETGEAR 341U Manual de usuario

NETGEAR

NETGEAR 7550 Manual de usuario

NETGEAR

NETGEAR CG814M Manual de usuario

NETGEAR

NETGEAR cg3000-2staus Manual de usuario

NETGEAR

NETGEAR DG834PN - RangeMax ADSL Modem Wireless... Guía del usuario

NETGEAR

NETGEAR XM128U Manual de usuario

NETGEAR

NETGEAR DM111PSP - ADSL2+ Ethernet Modem Manual de usuario

NETGEAR

NETGEAR DGND3700v2 Manual

NETGEAR

NETGEAR NIGHTHAWK CAX25 Manual de usuario

NETGEAR

NETGEAR DG834GV Instrucciones de instalación

NETGEAR

NETGEAR Nighthawk CM2050V Manual de usuario

NETGEAR

NETGEAR D3600? D6000 Manual de usuario

NETGEAR

NETGEAR XM128 Manual de usuario

NETGEAR

NETGEAR AirCard 785S Manual de usuario

NETGEAR

NETGEAR GS908E Manual de usuario

NETGEAR

NETGEAR CG2003D Manual de usuario

NETGEAR

NETGEAR LB2120 Series Manual de usuario

NETGEAR

NETGEAR CM1000v2 Manual de usuario

NETGEAR

NETGEAR A7000 Manual de usuario

NETGEAR

NETGEAR AirCard 340U Manual de usuario

Manuales populares de Módem de otras marcas

Davicom

Davicom DM562AP Manual de usuario

EpiValley

EpiValley TATA indicom SXC-1080 Manual de usuario

Zte

Zte WiMAX Manual de usuario

Intelimax

Intelimax MA-2060 Manual de usuario

SMC Networks

SMC Networks D3CM1604V Manual de uso y cuidado

Telstra

Telstra Wi-Fi 4G Advanced Pro X Manual de usuario

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Manual de usuario

Samsung

Samsung AceLink SAM-335A Manual de usuario

Enfora

Enfora Enabler-G Guía de configuración rápida

iRZ

iRZ ATM2-232 Manual de usuario

Zhone

Zhone 6310 Manual de usuario

Paradyne

Paradyne Hotwire 7976 Manual de usuario

US Robotics

US Robotics 3453C Manual de usuario

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manual de usuario

Zte

Zte MF823 Manual de usuario

Four-Faith

Four-Faith F1403 Manual de usuario

Sierra Wireless

Sierra Wireless AIRLINK MP595W Manual de usuario

Gemtek

Gemtek WiMAX WIXFBR-103 Manual de usuario