NetComm NTC-400 Series Manual de usuario

Quick Start Guide

NTC-400 Series Router

| Industrial IoT

This quick start guide is designed to get you up and running quickly and familiarise

you with the NTC-400 Series router. More advanced set up instructions are

provided in the user guide which can be downloaded from

http://www.netcommwireless.com/product/m2m/ntc-400

| Industrial IoT

NTC-400 Series Router

Package contents

The NTC-400 Series package includes:

1 x NTC-400 Series Router

2 x Wall mounting

brackets

1 x Quick Start Guide

2 x 2.4GHz / 5GHz

WiFi antennas

4 x Wall mounting

bracket screws

1 x 8-pin Terminal block

Pre-requisites

To complete the installation, you may require certain items such as screwdrivers

and fasteners.

2 x Cellular antennas

| Industrial IoT

Terminal block

The 8-pin Terminal block provides the following interfaces:

1 3 5 7

2 4 6

1. Power (PWR)

2. Ground (GND)

3. Ignition (IGN)

4. Digital Input 1 (DI-1)

5. Digital Input 2 (DI-2)

6. Digital Output (DO)

7. RS232 Serial (TX/RX)

| Industrial IoT

NTC-400 Series Router

I/O specications

MODE

SPECIFICATIONS

Digital Input

(DI-1 and DI-2)

Trigger voltage (high) Logic level 1: 5 V to 30 V

Normal voltage (low) Logic level 0: 0 V to 1.0 V

Digital Output

(DO)

Voltage (Relay mode)

Logic level 1: Depends on external device.

Maximum voltage is 36 V.

Logic level 0: Floating, External pull-down

resister (10 k Ω, 0.5 W) is required.

Note: DO power is relayed from the PWR

pin on the 8-pin terminal block connector.

Maximum current 1 Amp @ 12 V, or 0.33 Amp @ 36 V

Power requirements

The NTC-400 Series router accepts DC power in the range of 9 V to 36 V. Follow

the above illustration to ensure that the power source is connected with the

correct polarity.

| Industrial IoT

SIM cards

SIM cards are inserted into the SIM slots located on the front panel of the device.

To access the SIM card slots, remove the protective plate using a screwdriver.

NOTE: SIM B is disabled on units purchased through Telstra. On these units,

insert the SIM card into slot A.

| Industrial IoT

NTC-400 Series Router

Conguring the router

The web interface can be accessed via WiFi or Ethernet.

Connecting via WiFi

1. Connect and power up the NTC-400 Series router.

2. On your client device (e.g. laptop, tablet), connect to the SSID labelled

“NetComm_2.4GHz_XXXX” or “NetComm_5GHz_XXXX” where “XXXX” is four

randomly generated digits. The unique SSID and password for the wireless

networks are printed on the back cover of this Quick Start Guide and on the

label afxed to the bottom of the device. Enter the WiFi password and then

continue to the “Accessing the web interface” section.

Connecting via Ethernet cable

1. Connect and power up the NTC-400 Series router.

2. Connect a standard straight-through Ethernet cable to your client PC and the

other end to any of the LAN ports on the back of the NTC-400 Series router.

Continue to the “Accessing the web interface” section.

Accessing the web interface

3. In a web browser on your client device, navigate to http://192.168.20.1

4. Enter the username and password printed on both the back cover of this

Quick Start Guide and on the label afxed to the bottom of the device, then

press Enter or the click the Login button. Refer to the User Guide for further

conguration instructions.

NOTE: We highly recommend that you secure the WiFi networks

upon initial installation and change the password used to access

the web interface.

| Industrial IoT

Unlocking the SIM card

If the inserted SIM card is PIN locked, navigate to Basic Network >

WAN & Uplink > WAN Interface IPv4 Network Status > WAN-1 > Edit >

Internet Setup > WAN-1 > Edit > Connection with SIM-A / SIM B card >

PIN Code to enter the PIN Code. Click the Save button to save your changes.

NOTE: SIM B is disabled on units purchased through Telstra. On these units,

congure the SIM card in slot A.

| Industrial IoT

NTC-400 Series Router

Updating the APN

The default connection proles for both SIM-A and SIM-B are congured for

automatic conguration. If you wish to congure the APN manually, navigate to

Basic Network > WAN & Uplink > WAN Interface IPv4 Network Status

> WAN-1 > Edit > Internet Setup > WAN-1 > Edit > Connection with

SIM-A / SIM B card, set Dial-Up Prole to “Manual-conguration” and enter

the APN into the APN eld. Click the Save button to save your changes.

NOTE: SIM B is disabled on units purchased through Telstra. On these units,

congure the SIM card in slot A.

| Industrial IoT

Verifying the

connection status

When the NTC-400 Series router is connected to the Internet, the “HIGH” or “LOW”

LED on the front of the device lights up to indicate the current signal strength.

To check the connection status from the web interface, navigate to Status >

Dashboard and conrm that there is a 3G/4G Interface displayed under the

Network Interface Status table.

Otros manuales para NTC-400 Series

Tabla de contenidos

Otros manuales de Enrutador de red de NetComm

NetComm

NetComm NTC-40 series Manual de usuario

NetComm

NetComm 4GM3W Manual operacional

NetComm

NetComm RTA100 Manual de usuario

NetComm

NetComm N3G002W Guía de inicio rápido

NetComm

NetComm NF15ACV Manual de usuario

NetComm

NetComm NB8 Manual de usuario

NetComm

NetComm NF5 Manual de usuario

NetComm

NetComm 3G29Wn Manual de usuario

NetComm

NetComm Freshtel NB9 Manual de usuario

NetComm

NetComm 3G25W-R Manual de usuario

NetComm

NetComm NB3300 Manual de usuario

NetComm

NetComm N3G005W Manual de usuario

NetComm

NetComm MyWay YMLO-3G8WV Manual de usuario

NetComm

NetComm N3G007W Manual de usuario

NetComm

NetComm Dynalink NP800 Series Manual de usuario

NetComm

NetComm 3G42W-M Manual de usuario

NetComm

NetComm Poe01 Manual de usuario

NetComm

NetComm NTC-40WV Manual de usuario

NetComm

NetComm NB3 Manual de usuario

NetComm

NetComm NTC-6200 Manual de usuario

NetComm

NetComm G.SHDSL 4-port Security Modem Routers NB712 Manual de usuario

NetComm

NetComm N3G007W Manual de usuario

NetComm

NetComm NB5PLUS4 Manual de usuario

NetComm

NetComm NB702 SHDSL Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad