NetComm NB1300 Manual de usuario

www.netcomm.com.au Rev. 2 - YML643

Page 2 NB1300 ADSL Modem

Contents

Introduction ....................................................................................................................3

Which configuration is best? ........................................................................... 3

Package Contents ........................................................................................... 4

Factory Defaults ............................................................................................... 4

Do I need a Micro filter? ................................................................................... 5

Ethernet Gateway Configuration ................................................................................... 6

Step 1: Connecting your computer to the NB1300......................................... 6

Step 2: Configuring the NB1300..................................................................... 7

Step 3: Configuring your Computer to use the NB1300 ................................ 9

Ethernet Modem (Bridge) Configuration ..................................................................... 10

Step 1: Connecting your computer to the NB1300....................................... 10

Step 2: Configuring the NB1300....................................................................11

Step 3: Configuring your Computer/Router to use the NB1300 .................. 12

USB Gateway (Router) Configuration ......................................................................... 13

Step 1: Connecting your computer to the NB1300....................................... 13

Step 2: Configuring the NB1300................................................................... 14

Step 3: Configuring your Computer to use the NB1300 .............................. 15

Trouble Shooting ......................................................................................................... 16

Resetting the NB1300 ADSL Modem............................................................ 16

Registering your NetComm Product........................................................................... 16

Contact Information ....................................................................................... 16

Trademarks and Notices............................................................................... 16

Warranty Registration Form .......................................................................... 17

Product Warranty............................................................................................ 19

Limitations of Warranty .................................................................................. 19

Rev. 2 - YML643 www.netcomm.com.au

NB1300 ADSL Modem Page 3

Introduction

This guide is supplied to help you connect your NB1300 ADSL Modem quickly to your

network or Windows computer.

If the NB1300 has already been used, we strongly recommend you reset and flush all settings of

the unit via the USB cable by pressing and holding the RESET button on the rear of the modem

for 10 seconds. Wait for the RDY light to begin pulsing before continuing.

Note: Please be aware that connection via USB is only supported in Windows 98SE,

Windows Me, Windows 2000 and Windows XP. For Windows 95, NT, Linux and

Macintosh you should use the Ethernet port of your NB1300.

Which configuration is best?

Your NB1300 ADSL Modem can be connected and configured in various ways, below is a

description of the most common modes of operation.

Ethernet Gateway (Router) - This is when the NB1300 is connected to your network switch

or hub and shares the Internet connection to all computers on the network. The NB1300 will log

on to your ISP on behalf of your computers and it will shield your computers from direct

Internet attack by using Network address Translation (NAT).

Ethernet Modem (Bridge) - This is when you plug the modem directly into the Ethernet port

of just one computer or another router (via a cross over Ethernet cable) you then must run

Internet connection software (often supplied by your ISP) on the computer or second router to

establish a connection to the Internet. This method means that the computer or router connected

to the Ethernet port of the NB1300 is exposed to the Internet and is given a public IP address.

USB Gateway (Router) - If you do not have an Ethernet port on your computer you can use

your USB port like an Ethernet port to connect to the NB1300. This "simulated" Ethernet port

is only for connecting to the NB1300 and is only available for Windows 98SE, Windows 2000

and Windows XP. The NB1300 will log on to your ISP on behalf of your computer and it will

shield your computer from Internet attack by using NAT. Note that the USB cable is not

supplied with the NB1300.

If you wish to configure the NB1300 in a different way to the examples above you should

consult a Network Specialist for more information.

Note: We recommend you change your Router’s password from the factory default

before connecting it to a network or the Internet. Refer to the “Admin Password”

section in the “Security” Menu.

This unit should only be connected to the Telecommunications Network through a

line cord which meets the requirements of ACA TS008.

www.netcomm.com.au Rev. 2 - YML643

Page 4 NB1300 ADSL Modem

Package Contents

The following items should be contained in your NB1300 ADSL Modem Package:

■Quick Start Guide

■ADSL Modem (NB1300)

■Power adaptor (12V AC / 1Amp)

■Telephone line cable (RJ11)

■Crossover network cable (RJ45)

■NetComm Communications CD-ROM (CRS767)

■USB Cable

Factory Defaults

The following table lists the Factory Defaults of your NB1300 ADSL Modem:

Field Setting Details

LANIPaddress: 192.168.1.1

LAN Subnet Mask: 255.255.255.0

DHCP Server: Enabled (pool 192.168.1.100 - 192.168.1.149)

User Name: admin

Password: password

Main Function: Router (Bridge Disabled)

WAN connection type: PPPoE LLC

VPI: 8

VCI: 35

Note: These defaults may change with firmware updates and factory changes please

consult the NetComm website to check for the latest defaults.

Rev. 2 - YML643 www.netcomm.com.au

NB1300 ADSL Modem Page 5

Do I need a Micro filter?

Micro filters are used to prevent common telephone equipment, such as phones, answering

machines and fax machines, from interfering with your ADSL service. If your ADSL enabled

phone line is being used with any other equipment other than your ADSL Modem then you will

need to use one Micro filter for each phone device.

Splitters may be installed when your ADSL line is installed or when your current phone line is

upgraded to ADSL. If your telephone line is already split you will not need to use a Microfilter

- check with your ADSL service provider if you are unsure.

Each micro filter is connected in-line with your telephone or fax machine so that all signals pass

through it. Telephones and/or facsimiles in other rooms that are using the same extension will

also require Microfilters. The following diagram gives an example of connecting your ADSL

Modem/Router using a Microfilter.

A suitable Microfilter can be purchased from NetComm or your Service Provider, if required.

www.netcomm.com.au Rev. 2 - YML643

Page 6 NB1300 ADSL Modem

Ethernet Gateway Configuration

Before continuing, ensure you have the following items and information ready:

■A Windows 98, ME, NT, 2000 or XP client machine with a Network Interface Card

installed.

■Either a Network Hub and two UTP cables OR one Crossover UTP cable.

■A telephone line with ADSL service enabled.

■User Name, Password, VPI, VCI, encapsulation and DNS server settings for your ADSL

account (ask your ISP if unsure) .

Note: The following procedure presumes your NB1300 is set to a factory default IP

address 192.168.1.1.

Step 1: Connecting your computer to the NB1300

■Using either a hub and two UTP cables, or just one crossover UTP cable, connect the

NB1300 Modem Router to your computer.

■Connect one end of the ADSL phone line to the NB1300 ADSL Modem and the other end

to the wall socket.

■Connect the power pack to the NB1300 ADSL Modem and switch on the power switch.

■Ensure that there is a LAN link light on the NB1300.

■Ensure that the computer you intend to use has an IP address in the same subnet as the

NB1300 ADSL Modem. (e.g. the NB1300’s default IP is 192.168.1.1 - your computer

should be on 192.168.1.100 or similar.) If you have DHCP enabled on your computer, the

NB1300 will assign your computer a suitable IP address.

■Ensure that your computer has a LAN link light.

Rev. 2 - YML643 www.netcomm.com.au

NB1300 ADSL Modem Page 7

Step 2: Configuring the NB1300

1. After connecting all the ADSL Router cables, powering on the ADSL Router, and launching

a web browser, such as Internet Explorer or Netscape Navigator, browse to the address

http://192.168.1.1.

2. Enter the correct user name and password to access the Configuration tool. The default user

name and password are as below.

User Name : admin

Password: password

Note: You must click the Submit button on every page that you make changes on and

when you have made all your changes click the Save Setting and Reboot button

from the bottom of the menu.

3. Click on the One Page Setup link under the Basic menu. You do not need to change the

LAN settings unless you need the NB1300 to work with an existing network on a subnet

other than 192.168.1.x.

You will need to Change your WAN and VC settings as provided by your ISP. The following

lists an example of the most common ISP settings used in Australia. The fields that require

changing from the default settings are highlighted.

www.netcomm.com.au Rev. 2 - YML643

Page 8 NB1300 ADSL Modem

Field Setting Details

Service name: Any name to describe your ISP

User Name: Your ISP will provide a case sensitive User Name in a

format similar to your email address. Contact your ISP

for details

Password: Enter your Password as supplied by your Service

Provider (characters are usually all lower case)

Disconnect timeout: 0 ❖

Mode/Wan Connection Type: PPPoE LLC or PPPoA

VPI: 8 ❖

VCI: 35 ❖

Static IP Address: 192.168.241.101 ❖

Subnet Mask: 255.255.255.0 ❖

Default Gateway: 0.0.0.0 ❖

Bridge mode: Disabled ❖

❖

Default Setting. Although in most cases you will not be required to alter these

default settings for your NB1300, your ISP may identify specific settings to enable

connection to their service. Please refer to your ISP or Network Administrator for

further information.

4. Click Submit and then click the Save Setting and Reboot button from the bottom of the

menu. Wait for the configuration to complete.

Standard configuration of your NetComm NB1300 ADSL Modem is now complete. You

should be able to access the Internet through the unit, when it is set to be your gateway on

your computer/s. Refer to Step 3 for more information.

Rev. 2 - YML643 www.netcomm.com.au

NB1300 ADSL Modem Page 9

Step 3: Configuring your Computer to use the NB1300

To use the NB1300 ADSL Modem to access the Internet, your computer must have an IP

Address that is in the same LAN subnet as the NB1300 ADSL Router and use the NB1300

ADSL Router’s IP address as its gateway.

Most applications call for the Primary and Secondary DNS server entries to be made on each

computer. These can be automatically assigned by another DHCP server or by enabling the

DHCP server on the NB1300 ADSL Modem, and entering the DNS values in the DNS section

of the NB1300.

The following example shows how a computer could be set up when the NB1300 ADSL

Modem is configured with no DHCP service for this example. The NB1300 ADSL Modem

would be set to a LAN IP Address (Gateway) of 192.168.1.1 with a Subnet Mask of

255.255.255.0

Open the Control Panel and double click on the Network icon. Scroll down to select

TCP/IP-> Ethernet Card and click on the Properties button.

Note: When using Internet Explorer as a web

browser, click on the “Tools” menu and select

“Internet Options”. Select the “Connections”

tab and click on the “LAN Settings” button.

Tick the “Automatically detect settings”

checkbox and make sure the “Use a Proxy

server” checkbox is unchecked.

Your DNS numbers are

specific to your ISP and

should be notified along

with your User Name and

Password.

www.netcomm.com.au Rev. 2 - YML643

Page 10 NB1300 ADSL Modem

Ethernet Modem (Bridge) Configuration

Before continuing, ensure you have the following items and information ready:

■A computer with a Network Interface Card installed or a router (such as the NetComm

NB3100).

■A Crossover UTP cable.

■A telephone line with ADSL service enabled.

■User Name, Password, VPI, VCI, encapsulation and DNS server settings for your ADSL

account (ask your ISP if unsure). These are not needed for the NB1300, but are required for

the computer or router that it will be connected to.

Note: The following procedure presumes your NB1300 is set to a factory default IP

address 192.168.1.1.

Step 1: Connecting your computer to the NB1300

■Using a Crossover network cable, connect the Ethernet port of the NB1300 into the Ethernet

port of the computer you wish to use to configure the unit.

■Connect the power and switch the NB1300 on.

■Ensure the LAN link on the NB1300 is active.

■Configure your Computer to use any IP address in the range of 192.168.1.2 to

192.168.1.254.

Note: When the NB1300 is used in Bridge mode it is a fairly passive device and most

Internet configuration required (such as User Name, Password, etc.) is done on the

computer or another router.

Otros manuales para NB1300

Tabla de contenidos

Otros manuales de Módem de NetComm

NetComm

NetComm Webmaster CD1800 Manual de usuario

NetComm

NetComm NB3 Manual de usuario

NetComm

NetComm NTC-3000 Series Manual de usuario

NetComm

NetComm NB5580W Manual de usuario

NetComm

NetComm NB16WV-02 Manual de usuario

NetComm

NetComm NB1300 Manual de usuario

NetComm

NetComm NB604N Hoja de especificaciones

NetComm

NetComm NP7042 Manual de usuario

NetComm

NetComm AM5056 Manual de usuario

NetComm

NetComm NB1200 Manual de usuario

NetComm

NetComm IG6000 Manual de usuario

NetComm

NetComm NB1200 Manual de instrucciones

NetComm

NetComm Vodafone MachineLink 3G Manual de usuario

NetComm

NetComm NB9WMAXXn Manual

NetComm

NetComm IG6000 Manual de usuario

NetComm

NetComm N3GS003 Manual de usuario

NetComm

NetComm BD3068 Manual de usuario

NetComm

NetComm NTC-4000 series Manual de usuario

NetComm

NetComm NP5420 Manual de usuario

NetComm

NetComm NB16WV Guía de inicio rápido

NetComm

NetComm NF18MESH Manual de usuario

NetComm

NetComm NB16WV Guía de instalación

NetComm

NetComm NB3 Manual de usuario

NetComm

NetComm CD2004 Mega-i-Modem Manual de usuario

Manuales populares de Módem de otras marcas

Davicom

Davicom DM562AP Manual de usuario

EpiValley

EpiValley TATA indicom SXC-1080 Manual de usuario

Zte

Zte WiMAX Manual de usuario

Intelimax

Intelimax MA-2060 Manual de usuario

SMC Networks

SMC Networks D3CM1604V Manual de uso y cuidado

Telstra

Telstra Wi-Fi 4G Advanced Pro X Manual de usuario

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Manual de usuario

Samsung

Samsung AceLink SAM-335A Manual de usuario

Enfora

Enfora Enabler-G Guía de configuración rápida

iRZ

iRZ ATM2-232 Manual de usuario

Zhone

Zhone 6310 Manual de usuario

Paradyne

Paradyne Hotwire 7976 Manual de usuario

US Robotics

US Robotics 3453C Manual de usuario

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manual de usuario

Zte

Zte MF823 Manual de usuario

Four-Faith

Four-Faith F1403 Manual de usuario

Sierra Wireless

Sierra Wireless AIRLINK MP595W Manual de usuario

Gemtek

Gemtek WiMAX WIXFBR-103 Manual de usuario