Neptronic BM000N Manual de usuario

Actuator

Specification & Installation Instructions

BM-N-210803 1

Technical Data

BM000N

BM000FN

BM000FFN

BM060N

BM060FN

BM060FFN

BM020N

BM020FN

BM020FFN

Running time through 90º

15 sec

6 sec

3 sec

15 sec

6 sec

3 sec

15 sec

6 sec

3 sec

Power consumption

10 VA

18VA Peak,

10VA

18VA Peak,

10VA

18VA Peak,

10VA

10 VA

Torque

50 in.lb. [5,6 Nm] at rated

voltage

35 in.lb.

[3,9 Nm] at

rated voltage

50 in.lb. [5,6 Nm] at rated

voltage

35 in.lb.

[3,9 Nm] at

rated voltage

50 in.lb. [5,6 Nm] at rated

voltage

35 in.lb.

[3,9 Nm] at

rated voltage

Fail safe - Enerdrive

Yes

Auxiliary switches

Yes (2)

Ingress protection

IP22 equivalent to Nema type 2, IP54 equivalent to Nema type 3R if water tight

inlet bushings (not supplied NEP617) are installed

IP22 equivalent to Nema type 2

Feedback

4 to 20 mA or 2 to 10 VDC adjustable (default setting: 4 to 20mA)

Power supply

22 to 26 VAC or 28 to 32 VDC

Electrical connection

18 AWG [0.8 mm2] minimum

Inlet bushing

2 inlet bushing of 13/16 in [20.6 mm]

Control signal

Analog, Digital or Pulse with modulation (PWM) programmable (default setting: Analog control signal)

Angle of rotation

0 to 90 degrees, mechanically adjustable (default setting: 90º stroke)

Direction of rotation

Reversible, Clockwise (CW) or Counterclockwise (CCW) (default setting: CW direction)

Ambient temperature

-22ºF to +122ºF [-30º C to +50º C]

Storage temperature

-22ºF to +122ºF [-30º C to +50º C]

Relative Humidity

5 to 95 % non condensing.

Weight

3 lbs. [1.4 kg]

Warning: Do not press the clutch when actuator is powered

Dimensions

Dimension

Inches

Metric (mm)

1.50

38.1

3.64

92.5

6.60

167.5

model 000 & 060

3.02

76.8

model 020

3.81

96.8

Caution

We strongly recommend that all Neptronic®products be wired to a separate transformer and that transformer shall service only Neptronic®products. This precaution will

prevent interference with, and/or possible damage to incompatible equipment.

When multiple actuators are wired on a single transformer, polarity must be observed. Long wiring runs create voltage drop which may affect the actuator performance.

Enerdrive System U.S.A. Patent #5,278,454

Feature:

•Mounts easy on round & square shaft (with option –8).

•External clutch for manual adjustments.

•Maintenance free.

•Position indicator.

•Control signal fully programmable.

•Auto stroke on power up

•Brushless DC driven motor.

•Fail safe by Enerdrive System1(on model 060).

•Auxiliary switches (on model 020)

BM000N

BM020N

BM060N

BM000FN

BM020FN

BM060FN

BM000FFN

BM020FFN

BM060FFN

BM000/020/060(F)(FF)N

Specification & Installation Instruction

Mechanical Installation

1. Manually close the damper blades and positioned the

actuator at 0º or 90º.

2. Slide the actuator onto the shaft.

3. Tighten the nuts on the “U” bolt to the shaft with a 8mm

wrench to a torque of 60 in.lb. [6,7 Nm].

4. Slide the mounting bracket under the actuator. Ensure free

movement of the slot at the base of the actuator. The

bracket pin must be placed in the mid distance of the slot.

5. Fix the bracket to the ductwork with #8 self-tapping screws.

Wiring Diagrams

Analog or PWM

Digital signal

Digital –3 wire / 2 position

Digital –4 wire / 3 point floating

Special consideration for Digital control

In this mode, the actuator is sensitive to induced electrical voltages from external sources. To prevent such interference, if the signal on pins 4 and 3

on TB1 are from an external 24 Vac source, install a resistor 2.2kohm, 0.5W between pins 4 and 1 and another of 2.2kohms, 0.5W between pins 3

and 1 of TB1. These resistors are included.

Input Signal and Feedback setup

Input Signal

Feedback

Analog Mode

Input Signal is set with Dipswitch # 3

DS1-3 at OFF = 2 –10Vdc (default setting)

DS1-3 at ON = 4 –20mA

Feedback is set with Dipswitch #4

DS1-4 at OFF = 4 –20mA (default setting)

DS1-4 at ON = 2 –10Vdc

Digital & PWM

Mode

No Input Signal Setting

DS1-3 MUST be at OFF

CLUTCH

MOUNTING

BRACKET

1 2 3 4 5

COMMON (-)

TB1

24 Vac or 30 Vdc (+) INPUT SIGNAL

FEEDBACK

24 Vac (+)

2.2 K

1 2 3 4 5

FEEDBACK

DRIVE CCW

TB1

COMMON (-)

DRIVE CW

2.2 K

1 2 3 4 5

FEEDBACK

DRIVE CCW

COMMON (-)

24 VAC (+)

TB1

DRIVE CW

BM000/020/060(F)(FF)N

Specification & Installation Instruction

1 2 3 4

Rotation: CCW

Input in mA Feedback in Vdc

Fail safe return at 90º

1 2 3 4

Rotation: CW

Input in Vdc Feedback in mA

Fail safe return at 0º

PC Board

Dip switch settings

Default Setting = All dipswitches at OFF

Stroke adjustment –No control signal change

1. Apply power and, WAIT FOR LED TO BE OFF (around 10 seconds).

2. Press and release the reset button to start the auto-stroke process.

The LED should be illuminated.

•First option:

The actuator will then travel in both directions to find its limit and position itself according to the demand.

The LED will extinguish, the process is complete.

•Second option:

When the desired start position is reached, press and release the reset button. The actuator will now go the end

position. (you can also press and release the reset button when It's reaches the end position)

The LED will extinguish, the process is complete.

Programming –Change of control signal & PWM pulse setting

1. Remove power and put all dip switches "OFF" (default setting).

2. Apply power and, within 10 seconds, press and release the reset button. The LED should be blinking.

3. Select the control signal with dip switches:

Digital or Analog Modes

PWM Mode

Move switch No1 "ON” and then “OFF”.

Digital (On/Off or 3 point floating)

5 sec. pulse (default setting)

Move switch No2 "ON” and then “OFF”.

Analog (Default)

25 sec. pulse

Stroke adjustment

see the stroke adjustment section above.

Enabling or disabling PWM mode

1. Remove power supply to actuator

2. Install jumper between pin 3 & 4 of JP7

3. Select the desired action using the dipswitches (DS1):

DS1-1

DS1-2

Action

OFF

Enable PWM Mode

OFF

Disable PWM Mode

4. Re-apply power supply to actuator

5. Wait 5 seconds

6. Remove power supply to actuator

7. Remove jumper between pin 3 & 4 of JP7, re-install it between pin 4 & 5.

8. Re-apply power supply to actuator

PWM is factory preset at 5 sec. pulse,

refer to programming section above to change pulse setting.

When not used for programming,

jumper is placed between pin 4 & 5

BM060N/GMR

1 2 3 4 5

1 2 3 4

JP7

Microcontroller

Pins for PWM selection

Reset button

Dip switch

LED

Terminal

JP7

Pin #1

Pin #5

Pin #2

Pin #3

Pin #4

BM000/020/060(F)(FF)N

Specification & Installation Instruction

Zero and span calibration

This feature is applicable to analog control signal only.

1. Remove power and put all dip switches "OFF". (factory preset).

2. Apply power and, within 10 seconds press and hold the reset button until the LED blinks once.

The Zero and span calibration process then start.

3. Release the reset button. The LED is now constantly illuminated.

4. Apply new minimum voltage.

It can be any value between 0 to 7 Vdc, with an external 0 to 10 volt supply (ex: MEP).

5. Press and release the reset button to memorize the new minimum voltage. The LED blinks.

6. Apply new maximum voltage.

It can be any value between 3 to 10 Vdc, this value should be greater than the new minimum value.

7. Press and release the reset button to memorize the new maximum voltage. The LED blinks.

The Zero and span calibration process is complete.

Note: To reset zero and span to 2 to 10 Vdc (default setting). You just have to re-select the analog control signal mode, see

Programming.

Wiring Diagrams for auxiliary switches (on model 020)

Auxiliary switch rating:

5 Amp resistive, 250 Vac

BLACK

RED

GREEN

BROWN

WHITE

BLUE

LOWER COMMON

LOWER CLOSED 10-90º

LOWER CLOSED 0-10º

UPPER COMMON

UPPER CLOSED 0-80º

UPPER CLOSED 80-90º

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Controladores de Neptronic

Neptronic

Neptronic BT100S Manual de usuario

Neptronic

Neptronic HRO20 Manual de usuario

Neptronic

Neptronic BT000F Manual de usuario

Neptronic

Neptronic LT060X11 Manual de usuario

Neptronic

Neptronic EVCB14NIT4X/TRL24 Series Manual de usuario

Neptronic

Neptronic TM000N Manual de usuario

Neptronic

Neptronic BT160 Manual de usuario

Neptronic

Neptronic TUCB Series Manual de usuario

Neptronic

Neptronic BM000S Manual de usuario

Neptronic

Neptronic TSU00 Series Manual de usuario

Neptronic

Neptronic BBT24A Manual de usuario

Neptronic

Neptronic BBTS1000 Manual de usuario

Neptronic

Neptronic BBTHV1100A Manual de usuario

Neptronic

Neptronic HRO20LSS Manual de usuario

Neptronic

Neptronic TSUB00 Series Manual de usuario

Neptronic

Neptronic BT060X8 Manual de usuario

Neptronic

Neptronic EVCB14NIT0S Manual de usuario

Neptronic

Neptronic TM200FN Manual de usuario

Neptronic

Neptronic BT000 Manual de usuario

Neptronic

Neptronic BM200S Manual de usuario

Neptronic

Neptronic BM000 Manual de usuario

Neptronic

Neptronic TM200N Manual de usuario

Neptronic

Neptronic ARO24T Manual de usuario

Neptronic

Neptronic EVCB Series Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario