NEC XN120 Vision Manual de usuario
XN120
UserProManual
1.0
This manual has been developed by NEC Infrontia LTD It is intended for the use of its customers and service
personnel, and should be read in its entirety before attempting to install or program the system. Any comments or
suggestions for improving this manual would be appreciated. Forward your remarks to:
NEC Infrontia LTD
75 Swingbridge Road, Loughborough Leicestershire.
tech_support@necinfrontia.co.uk
www.necinfrontia.co.uk
Nothing contained in this manual shall be deemed to be, and this manual does not constitute, a warranty of, or
representation with respect to, any of the equipment covered. This manual is subject to change without notice and
NEC Infrontia has no obligation to provide any updates or corrections to this manual. Further, NEC Infrontia also
reserves the right, without prior notice, to make changes in equipment design or components as it deems
appropriate. No representation is made that this manual is complete or accurate in all respects and NEC Infrontia
shall not be liable for any errors or omissions. In no event shall NEC Infrontia be liable for any incidental or
consequential damages in connection with the use of this manual. This document contains proprietary information
that is protected by copyright. All rights are reserved. No part of this document may be photocopied or reproduced
without prior written consent of NEC Infrontia
©2006 by NEC Infrontia LTD
UserPro Manual - 3
Document History
Revision 1.0 September 2006
First Release
UserPro Manual - 4
Table of Contents
Table of Contents 1
Table of Contents
Connecting to the System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
EXIFU Card and Connections for PCPro . . . . . . . . . . . . . . . . . . . . . . 2
Ethernet Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Local LAN (Ethernet) Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Common Buttons within UserPro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Using UserPro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Table of Contents
2 Table of Contents
Connecting to the System
UserPro Manual 1
Connecting to the System
Connecting to the System
In addition to the system phone programming, the system provides the ability to use a PC to access system programming. The
HTML-based UserPro allows you to:
•Edit the telephone system programming options from a remote location.
The UserPro application applies the changes as soon as the APPLY or OK icon is clicked.
UserPro PC Requirements
•CPU: Pentium III 600 MHz equivalent or higher
•Monitor Resolution: 800 x 600 pixels or higher
•Mouse
•Microsoft Windows 2000/XP
•Internet Browser: Internet Explorer 6.0 or higher or
Netscape 6.0 or higher
•Network Interface Card (NIC) (depending on connection type)
The browser settings should allow all Cookies and have Scripting/Active Scripting enabled.
Internet Explorer: Click Tools-Internet Options-Security-Internet or Local Intranet (depending on your connec-
tion)-Custom Level. Set Allow Cookies That Are Stored On Your Computer and Allow Per-Session Cookies (Not
Stored) to “Enable”. Set Active Scripting to “Enable”.
Netscape: Click Edit-Preferences. Under Privacy & Security, set Cookies to “Enable All Cookies”. Under Advanced-
Scripts & Plugins the checkbox for Enable JavaScript for Navigator should be checked.
Connecting to the System
2UserPro Manual
The following changes must be made in order to connect to the system.
With the telephone system set at default (Program 10-12-01 = IP Address 172.16.0.10 and Program 10-13-01 = 0 [DHCP Server
disabled]):
1. The network settings on the PC connecting to the telephone system must be changed. Set the IP address to 172.16.0.11
(172.16.0.12, 172.16.0.13, etc would also be acceptable) and change the subnet mask to 255.255.0.0.
With the telephone set to use the built-in DHCP Server (Program 10-12-01 = IP Address 172.16.0.10 and Program 10-13-
01 = 1 [DHCP Server enabled]):
1. The network settings on the PC connecting to the telephone system must be set to obtain an IP address automatically.
The location of the IP setting depends on the Windows version being used, but for example, with Windows
XP you would access these settings by clicking:
START-SETTINGS-NETWORK CONNECTIONS-Right mouse click on LOCAL AREA CONNECTION-
Select PROPERTIES-Click on INTERNET PROTOCOL (TCP/IP)-Click PROPERTIES-Select the GENERAL tab
if not already selected.
Connecting to the telephone System
In order to use UserPro, the telephone system must be connected to the PC as shown below.
For local connection you can connect via Ethernet either through a hub or with a cross-over cable connected directly to the
system, a USB cable or a serial cable.
For remote connection you can connect your PC to an ISDN Terminal Adapter and make a dial up connection to the telephone
sytem.
EXIFU Card and Connections for PCPro
Ethernet Connection
You will need the EXIFU-A card installed in the system.
Connect the Ethernet socket of the EXIFU-A card to a NIC card on yout PC. This can be either via LAN or directly via a LAN
cross cable.
You will need to setup the NIC in your PC before you can communicate with the system.
Connecting to the System
UserPro Manual 3
LAN Cable
Straight through RJ45 patch cable.
LAN Cross Cable
RJ45 cable with cross over Tx and Rx.
Pin Pin
11
22
33
66
Pin Pin
13
26
31
62
Local LAN (Ethernet) Connection
4UserPro Manual
Local LAN (Ether net) Connection
Local LAN (Ethernet) Connection
When connection to the telephone system is made using UserPro via a LAN connection, an IP address and the subnet type
must be assigned to the PC. The IP address and subnet mask are determined by the telephone system in Programs 10-12-01
and 10-12-02.
If the PC is already connected to a network and you are connecting to the NTCPU through a hub or router,
please check with your network manager to determine the IP address that should be used.
The following information is based on a stand-alone PC connected to the telephone system, with the telephone system using
the default settings for the IP address and subnet mask (Program 10-12-01: IP Address 172.16.0.10 / Program 10-12-02: Sub-
net Mask 255.255.0.0).
1. To change the TCP/IP information OF YOUR PC, click START +SETTINGS +NETWORK CONNECTIONS. The fol-
lowing window appears.
2. Right-click on the LOCAL AREA CONNECTION icon and click on PROPERTIES.
3. In the list of items, click on the INTERNET PROTOCOL (TCP/IP) and then click on PROPERTIES.
Otros manuales para XN120 Vision
15
Tabla de contenidos
Otros manuales de Sistema telefónico de NEC
NEC
NEC Electra Elite DSS Manual de usuario
NEC
NEC Xen Alpha Manual de usuario
NEC
NEC 1232 AK Series Manual de usuario
NEC
NEC SL1100 Manual de usuario
NEC
NEC XN120 Vision Manual de usuario
NEC
NEC SL1100 Manual de usuario
NEC
NEC UX5000 Manual de usuario
NEC
NEC dX-Z Series Manual de usuario
NEC
NEC TOPAZ Manual de usuario
NEC
NEC DSX Manual de usuario
NEC
NEC Univerge SV9100 Manual de usuario
NEC
NEC ELECTRA ELITE IPK II Manual de usuario
NEC
NEC Electra mark II Manual de usuario
NEC
NEC Univerge SV8100 Manual de instrucciones
NEC
NEC Univerge SV9100 Manual de usuario
NEC
NEC DSX Manual de usuario
NEC
NEC Xen Topaz Manual de usuario
NEC
NEC DSX-40 DEMO KIT Manual de usuario
NEC
NEC DSX Manual de usuario
NEC
NEC Nitsuko 32i Manual de instrucciones
Manuales populares de Sistema telefónico de otras marcas
ASCOM
ASCOM TD 92375GB Manual del propietario
Karel
Karel MS26S Hoja de información del producto
EnGenius
EnGenius DuraFon PRO Manual de usuario
Teledat
Teledat X130 DSL Manual de usuario
SpectraLink
SpectraLink MOG400 Manual de usuario
LG-Nortel
LG-Nortel 300 Series Instrucciones de funcionamiento y seguridad