National Instruments PXI-5154 Manual de usuario

GETTING STARTED GUIDE

PXI/PCI-5154

2 GS/s Oscilloscope

Note Before you begin, install and configure your chassis and controller.

This document explains how to install, configure, and test the PXI/PCI-5154. The

PXI/PCI-5154 high-speed oscilloscope features 1 GHz analog bandwidth and up to 2 GS/s

real-time sample rate (20 GS/s equivalent-time sample rate for repetitive signals).

To access PXI/PCI-5154 documentation, navigate to Start»All Programs»National

Instruments»NI-SCOPE»Documentation.

Caution You can impair the protection provided by the PXI/PCI-5154 if you use it

in a manner not described in this document.

Contents

Electromagnetic Compatibility Guidelines...............................................................................2

Verifying the System Requirements..........................................................................................2

Unpacking the Kit..................................................................................................................... 2

Kit Contents...................................................................................................................... 3

Other Equipment....................................................................................................................... 3

Preparing the Environment....................................................................................................... 4

PXI Modules..................................................................................................................... 4

PCI Modules..................................................................................................................... 4

Installing the Software.............................................................................................................. 4

Installing the PXI-5154.............................................................................................................5

Installing the PCI-5154............................................................................................................. 6

PXI/PCI-5154 Front Panel Connectors and Indicators............................................................. 8

Configuring the PXI/PCI-5154 in MAX...................................................................................9

Programming the PXI/PCI-5154.............................................................................................10

NI-SCOPE Examples...................................................................................................... 11

Making a Measurement...........................................................................................................12

Making a Measurement with NI-SCOPE SFP................................................................12

Making a Measurement with LabVIEW.........................................................................12

Setting Up PXI/PCI-5154 for Synchronization...................................................................... 12

PXI Modules................................................................................................................... 13

PCI Modules................................................................................................................... 13

Troubleshooting...................................................................................................................... 13

Why Is the ACCESS LED Off When the Chassis Is On?...............................................13

What Should I Do if the PXI/PCI-5154 Doesn't Appear in MAX?................................ 14

What Should I Do if the Module Fails the Self-Test?.....................................................14

Thermal Shutdown Error................................................................................................ 14

Where to Go Next................................................................................................................... 15

Worldwide Support and Services............................................................................................ 16

Electromagnetic Compatibility Guidelines

This product was tested and complies with the regulatory requirements and limits for

electromagnetic compatibility (EMC) stated in the product specifications. These requirements

and limits provide reasonable protection against harmful interference when the product is

operated in the intended operational electromagnetic environment.

This product is intended for use in industrial locations. However, harmful interference may

occur in some installations, when the product is connected to a peripheral device or test object,

or if the product is used in residential or commercial areas. To minimize interference with

radio and television reception and prevent unacceptable performance degradation, install and

use this product in strict accordance with the instructions in the product documentation.

Furthermore, any changes or modifications to the product not expressly approved by National

Instruments could void your authority to operate it under your local regulatory rules.

Verifying the System Requirements

To use the PXI/PCI-5154, your system must meet certain requirements. For more information

about minimum system requirements, recommended system, and supported application

development environments (ADEs), refer to the readme, which is available on the software

media or online at ni.com/updates.

Unpacking the Kit

Caution To prevent electrostatic discharge (ESD) from damaging the device,

ground yourself using a grounding strap or by holding a grounded object, such as

your computer chassis.

1. Touch the antistatic package to a metal part of the computer chassis.

2. Remove the device from the package and inspect the device for loose components or any

other sign of damage.

Caution Never touch the exposed pins of connectors.

Note Do not install a device if it appears damaged in any way.

3. Unpack any other items and documentation from the kit.

Store the device in the antistatic package when the device is not in use.

2| ni.com | PXI/PCI-5154 Getting Started Guide

Kit Contents

Figure 1. PXI/PCI-5154 Kit Contents

45 6

1. Hardware Module

2. Driver Software DVD

3. Screw Kit, part number 191306A-01 (ships only

with PCI kit)

4. Getting Started Guide (this document)

5. Maintain Forced-Air Cooling Note to Users

6. Export Compliance Note to Users

Other Equipment

There are several required items not included in your device kit that you need to operate the

PXI/PCI-5154. Your application may require additional items not included in your kit to install

or operate your device.

• (PXI Devices) A PXI chassis, a PXI/SCXI combination chassis, or a PXI/CompactPCI

chassis with a controller and the chassis documentation

• (PCI Devices) A desktop computer and its documentation

Note If your application uses NI-TClk synchronization for PCI devices, you must

use a RTSI cable to connect the PCI devices. For more information, refer to NI

High-Speed Digitizers Help»Programming»Reference»NI-TClk

Synchronization Help.

Optional Items

• PXI Chassis Slot Blocker kit (NI part number 199198-01)

• SMB (m)-to-SMB (m) cables

PXI/PCI-5154 Getting Started Guide | © National Instruments | 3

Preparing the Environment

Ensure that the environment in which you are using the PXI/PCI-5154 meets the following

specifications.

PXI Modules

Operating Environment

Ambient temperature range 0 °C to 55 °C (Tested in accordance with

IEC 60068-2-1 and IEC 60068-2-2.)

Relative humidity range 10% to 90%, noncondensing (Tested in

accordance with IEC 60068-2-56.)

Maximum altitude 2,000 m (at 25 °C ambient temperature)

Pollution Degree 2

Indoor use only.

PCI Modules

Operating Environment

Ambient temperature range 0 °C to 45 °C (Tested in accordance with

IEC 60068-2-1 and IEC 60068-2-2.)

Relative humidity range 10% to 90%, noncondensing (Tested in

accordance with IEC 60068-2-56.)

Maximum altitude 2,000 m (at 25 °C ambient temperature)

Pollution Degree 2

Indoor use only.

Caution Clean the hardware with a soft, nonmetallic brush. Make sure that the

hardware is completely dry and free from contaminants before returning it to

service.

For complete specifications, refer to specifications document for your device at ni.com/

manuals.

Installing the Software

You must be an Administrator to install NI software on your computer.

1. Install an ADE, such as LabVIEW or LabWindows™/CVI™.

2. Insert the driver software media into your computer. The installer should open

automatically.

4| ni.com | PXI/PCI-5154 Getting Started Guide

If the installation window does not appear, navigate to the drive, double-click it, and

double-click autorun.exe.

3. Follow the instructions in the installation prompts.

Note Windows users may see access and security messages during

installation. Accept the prompts to complete the installation.

4. When the installer completes, select Restart in the dialog box that prompts you to restart,

shut down, or restart later.

Installing the PXI-5154

Caution To prevent damage to the PXI-5154 caused by ESD or contamination,

handle the module using the edges or the metal bracket.

1. Ensure the AC power source is connected to the chassis before installing the module.

The AC power cord grounds the chassis and protects it from electrical damage while you

install the module.

2. Power off the chassis.

3. Inspect the slot pins on the chassis backplane for any bends or damage prior to

installation. Do not install a module if the backplane is damaged.

4. Remove the black plastic covers from all the captive screws on the module front panel.

5. Identify a supported slot in the chassis. The following figure shows the symbols that

indicate the slot types.

Figure 2. Chassis Compatibility Symbols

NI PXIe-1062Q

12 3 45

1. PXI Express System Controller Slot

2. PXI Peripheral Slot

3. PXI Express Hybrid Peripheral Slot

4. PXI Express System Timing Slot

5. PXI Express Peripheral Slot

PXI-5154 modules can be placed in PXI peripheral slots or PXI Express Hybrid

peripheral slots.

6. Touch any metal part of the chassis to discharge static electricity.

7. Ensure that the ejector handle is in the downward (unlatched) position.

8. Place the module edges into the module guides at the top and bottom of the chassis. Slide

the module into the slot until it is fully inserted.

PXI/PCI-5154 Getting Started Guide | © National Instruments | 5

Figure 3. Module Installation

NI PXIe-1075

1. Chassis

2. Hardware Module

3. Ejector Handle in Downward (Unlatched) Position

9. Latch the module in place by pulling up on the ejector handle.

10. Secure the module front panel to the chassis using the front-panel mounting screws.

Note Tightening the top and bottom mounting screws increases mechanical

stability and also electrically connects the front panel to the chassis, which can

improve the signal quality and electromagnetic performance.

11. Cover all empty slots using EMC filler panels or fill using slot blockers to maximize

cooling air flow, depending on your application.

12. Power on the chassis.

Note For more information about maximizing cooling air flow, refer to the

Maintain Forced-Air Cooling Note to Users included in your kit.

Related Information

Why Is the ACCESS LED Off When the Chassis Is On? on page 13

Installing the PCI-5154

1. Power off and unplug the computer.

2. Access the computer system expansion slots. This step might require you to remove one

or more access panels on the computer case.

3. Locate a compatible slot and remove the corresponding slot cover on the computer back

panel. PCI-5154 modules can only be inserted into PCI slots.

Tip To maximize airflow and extend the life of the PCI device, leave any

adjacent PCI slots empty.

6| ni.com | PXI/PCI-5154 Getting Started Guide

4. Touch any metal part of the computer to discharge any static electricity.

5. Insert the module into the slot you selected. Gently rock the module in to place without

forcing it.

Figure 4. Module Installation

1. Module

2. System Expansion Slot

3. PC

6. Secure the module mounting bracket to the computer back panel rail.

Note Tightening the top mounting screw increases mechanical stability and

also electrically connects the front panel to the chassis, which can improve the

signal quality and electromagnetic performance.

7. Some computer manufacturers use a securing lever made of plastic to secure PCI devices;

such a lever is unacceptable and must be removed. Use the screw provided in the kit to

screw down the device. Otherwise, you must use a different computer chassis.

8. Replace any access panels on the computer case.

9. Power on your computer.

10. Verify that spread-spectrum clocking is enabled in the PC BIOS. For information about

how to verify this setting, refer to the PC user documentation

Note For SMC-based devices, spread-spectrum clocking varies the clock

signal to spread the timing clock signal over a small frequency range. Disabling

spread-spectrum clocking may affect the accuracy of device specifications.

PXI/PCI-5154 Getting Started Guide | © National Instruments | 7

PXI/PCI-5154 Front Panel Connectors and

Indicators

Refer to the following figure and table for information about front panel signal connections

and indicators for the PXI/PCI-5154.

Figure 5. PXI/PCI-5154 Front Panels

CH 0

CH 1

TRIG

PFI 1PFI 0

ACCESS ACTIVE

CH0

CH1

TRIG

PFI0

PFI1

Table 1. PXI/PCI-5154 Front Panel Signal Connections

Connector Description Function

CH 0, CH 1 Standard BNC female

connector

Analog input connection; digitizes data and

triggers acquisitions.

TRIG Standard BNC female

connector

External analog trigger connection; signals on the

TRIG connector cannot be digitized.

8| ni.com | PXI/PCI-5154 Getting Started Guide

Table 1. PXI/PCI-5154 Front Panel Signal Connections (Continued)

Connector Description Function

PFI 0 Standard SMB jack

connector

Multipurpose PFI line for Reference Clock In,

Sample Clock In, and Digital Trigger In/Out.

PFI 1 Standard SMB jack

connector

Multipurpose PFI line for Reference Clock Out,

probe compensation, and Digital Trigger In/Out.

Table 2. PXI-5154 Front Panel Indicators

Label Function

ACCESS Indicates the status of the PCI bus and the interface from the PXI-5154 to the

controller.

ACTIVE Indicates the status of the onboard acquisition hardware of the PXI-5154.

Configuring the PXI/PCI-5154 in MAX

Use Measurement & Automation Explorer (MAX) to configure your NI hardware. MAX

informs other programs about which NI hardware products are in the system and how they are

configured. MAX is automatically installed with NI-SCOPE.

1. Launch MAX.

2. In the configuration tree, expand Devices and Interfaces to see the list of installed NI

hardware.

Installed modules appear under the name of their associated chassis.

3. Expand your Chassis tree item.

MAX lists all modules installed in the chassis. Your default names may vary.

Note If you do not see your module listed, press <F5> to refresh the list of

installed modules. If the module is still not listed, power off the system, ensure

the module is correctly installed, and restart.

4. Record the identifier MAX assigns to the hardware. Use this identifier when

programming the PXI/PCI-5154.

5. Self-test the hardware by selecting the item in the configuration tree and clicking Self-

Test in the MAX toolbar.

The MAX self-test performs a basic verification of hardware resources.

6. Run the test panels on the device to verify the signal.

a) To access the test panels, right-click the device and select Test Panels. The

NI-SCOPE Soft Front Panel (SFP) launches automatically.

PXI/PCI-5154 Getting Started Guide | © National Instruments | 9

b) Do one of the following to connect a signal to the device:

• Connect an external signal by clicking Auto or by selecting the appropriate

device parameters for the signal, or

• Connect a cable from PFI 1 to an input channel and select Utility»Probe

Compensation from the SFP menu. Click Auto to display a 1 kHz square

wave.

Note The PXI/PCI-5154 has self-calibration capabilities, which you can

access programmatically with NI-SCOPE and your ADE, or interactively with

NI-SCOPE SFP or MAX.

Related Information

Making a Measurement on page 12

What Should I Do if the Module Fails the Self-Test? on page 14

What Should I Do if the PXI/PCI-5154 Doesn't Appear in MAX? on page 14

Programming the PXI/PCI-5154

You can acquire data interactively using the NI-SCOPE SFP, or you can use the NI-SCOPE

instrument driver to program your device in the supported ADE of your choice.

10 | ni.com | PXI/PCI-5154 Getting Started Guide

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de prueba de National Instruments

National Instruments

National Instruments Module SCXI-1125 Manual

National Instruments

National Instruments VirtualBench Manual de usuario

National Instruments

National Instruments PXI-5671 Manual de usuario

National Instruments

National Instruments PXIe-5185 Manual de usuario

National Instruments

National Instruments SCXI-116 Series Manual de usuario

National Instruments

National Instruments SMB-2145 Manual de usuario

National Instruments

National Instruments PXIe-5163 Manual de usuario

National Instruments

National Instruments NI SCB-68A Manual de usuario

National Instruments

National Instruments 5124 Manual

National Instruments

National Instruments mmWave OTA Manual de usuario

National Instruments

National Instruments PXIe-5172 Manual

National Instruments

National Instruments PXIe-5172 Manual de usuario

National Instruments

National Instruments PXIe-5170 Manual de usuario

National Instruments

National Instruments PXIe-5672 Manual de usuario

National Instruments

National Instruments ECUTS-16000 Manual de usuario

National Instruments

National Instruments 449 Series Manual

National Instruments

National Instruments PXIe-5160 Manual de usuario

National Instruments

National Instruments PXIe-5164 Manual de usuario

National Instruments

National Instruments GPIB Device Simulator EPROM Manual del propietario

National Instruments

National Instruments PXI-5670 Manual de usuario

National Instruments

National Instruments 5401 Manual de usuario

National Instruments

National Instruments VirtualBench VB-8054 Manual del propietario

National Instruments

National Instruments NI PXI-2567 Manual del propietario

National Instruments

National Instruments NI PXI-5922 Manual de usuario

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Agilent Technologies

Agilent Technologies BERT Serial Manual de usuario

Agilent Technologies

Agilent Technologies N3280A Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario