National Instruments PXIe-5433 Manual de usuario

GETTING STARTED GUIDE

PXIe-5433

80 MHz Bandwidth, 16-Bit PXI Waveform Generator

This document explains how to install, configure, test, and use the PXIe-5433. The PXIe-5433

ships with NI-FGEN driver software, which you can use to program the module.

Note Before you begin, install and configure your chassis and controller.

Caution This icon denotes a caution, which advises you to consult documentation

where this symbol is marked.

Caution You can impair the protection provided by the PXIe-5433 if you use it in

a manner not described in this document.

Contents

Electromagnetic Compatibility Guidelines...............................................................................2

Verifying the System Requirements..........................................................................................2

Unpacking the Kit..................................................................................................................... 2

Other Equipment....................................................................................................................... 3

Preparing the Environment....................................................................................................... 4

Installing the Software.............................................................................................................. 4

Installing the PXIe-5433........................................................................................................... 5

PXIe-5433 Pinout and LEDs.....................................................................................................6

PXIe-5433 SCB-19 Pinout..............................................................................................10

Configuring the PXIe-5433 in MAX...................................................................................... 11

Self-Calibrating the PXIe-5433.............................................................................................. 12

Generating Waveforms with the NI-FGEN Soft Front Panel................................................. 12

NI-FGEN Instrument Driver...................................................................................................13

Generating Waveforms with NI-FGEN and LabVIEW.......................................................... 13

Troubleshooting...................................................................................................................... 14

Why Is the ACCESS LED Off When the Chassis Is On?...............................................14

What Should I Do if the PXIe-5433 Doesn't Appear in MAX?......................................15

What Should I Do if the PXIe-5433 Fails the Self-Test or Self-Calibration?.................15

Where to Go Next................................................................................................................... 15

PXIe-5433 Firmware Licensing..............................................................................................16

Worldwide Support and Services............................................................................................ 16

Electromagnetic Compatibility Guidelines

This product was tested and complies with the regulatory requirements and limits for

electromagnetic compatibility (EMC) stated in the product specifications. These requirements

and limits provide reasonable protection against harmful interference when the product is

operated in the intended operational electromagnetic environment.

This product is intended for use in industrial locations. However, harmful interference may

occur in some installations, when the product is connected to a peripheral device or test object,

or if the product is used in residential or commercial areas. To minimize interference with

radio and television reception and prevent unacceptable performance degradation, install and

use this product in strict accordance with the instructions in the product documentation.

Furthermore, any changes or modifications to the product not expressly approved by National

Instruments could void your authority to operate it under your local regulatory rules.

Caution To ensure the specified EMC performance, operate this product only with

shielded cables and accessories.

Caution To ensure the specified EMC performance, the length of all I/O cables

must be no longer than 3 m (10 ft).

Verifying the System Requirements

To use the PXIe-5433, your system must meet certain requirements.

For more information about minimum system requirements, recommended system

requirements, and supported ADEs, refer to the readme for your selected software support.

Readmes are available on the driver software DVD and online at ni.com/updates.

Unpacking the Kit

Refer to the following figure to identify the contents of the PXIe-5433 kit.

2| ni.com | PXIe-5433 Getting Started Guide

Figure 1. PXIe-5433 Kit Contents

1. PXIe-5433

2. PXIe-5433 Getting Started Guide (this document)

3. Maintain Forced-Air Cooling Note to Users

Caution To prevent electrostatic discharge (ESD) from damaging the module,

ground yourself using a grounding strap or by holding a grounded object, such as

your computer chassis.

1. Touch the antistatic package to a metal part of the computer chassis.

2. Remove the module from the package and inspect it for loose components or other signs

of damage.

Caution Never touch the exposed pins of connectors.

Note Do not install a module if it appears damaged in any way.

3. Unpack any other items and documentation from the kit.

Store the module in the antistatic package when the module is not in use.

Other Equipment

There are several required items not included in your PXIe-5433 kit that you need to operate

the PXIe-5433. Your application may require additional items not included in your kit to

install or operate your PXIe-5433.

Required Items

• A PXI chassis and chassis documentation

• A PXI controller or PC with a device for PXI remote control system that meets the

system requirements specified in this guide and chassis documentation

PXIe-5433 Getting Started Guide | © National Instruments | 3

Optional Items

• PXI slot blocker kit (NI part number 199198-01)

• SCB-19 connector block (NI part number 785642-01)

• SHH19-MH19-AUX shielded single-ended cable, 1 M (NI part number 784091-01)

Visit ni.com for more information about these additional items.

Preparing the Environment

Ensure that the environment you are using the PXIe-5433 in meets the following

specifications:

Maximum altitude 2,000 m (800 mbar) (at 25 °C ambient

temperature)

Pollution Degree 2

Operating ambient temperature range 0 °C to 55 °C (Tested in accordance with

IEC 60068-2-1 and IEC 60068-2-2. Meets

MIL-PRF-28800F Class 3 low temperature

limit and MIL-PRF-28800F Class 2 high

temperature limit.)

Operating relative humidity range 10% to 90%, noncondensing (Tested in

accordance with IEC 60068-2-56.)

Indoor use only.

Related Information

Refer to the PXIe-5433 Specifications at ni.com for complete specifications.

Installing the Software

You must be an Administrator to install NI software on your computer.

1. Install an ADE, such as LabVIEW or LabWindows™/CVI™.

2. Visit ni.com/downloads/drivers and search for NI-FGEN.

3. Download the latest version of NI-FGEN by clicking Download and then running the

executable (.exe) file.

4. Follow the instructions in the installation prompts.

Note Windows users may see access and security messages during

installation. Accept the prompts to complete the installation.

5. When the installer completes, select Restart in the dialog box that prompts you to restart,

shut down, or restart later.

4| ni.com | PXIe-5433 Getting Started Guide

Installing the PXIe-5433

Caution To prevent damage to the PXIe-5433 caused by ESD or contamination,

handle the module using the edges or the metal bracket.

Caution Clean the hardware with a soft, nonmetallic brush. Make sure that the

hardware is completely dry and free from contaminants before returning it to

service.

The PXIe-5433 is a single-slot module with one backplane connector. The module may be

installed into any PXI Express-compatible slot.

1. Ensure the AC power source is connected to the chassis before installing the PXIe-5433.

The AC power cord grounds the chassis and protects it from electrical damage while you

install the PXIe-5433.

2. Power off the chassis.

3. Inspect the slot pins on the chassis backplane for any bends or damage prior to

installation. Do not install a module if the backplane is damaged.

4. Position the chassis so that inlet and outlet vents are not obstructed.

For more information about optimal chassis positioning, refer to the chassis

documentation.

5. Remove the black plastic covers from all the captive screws on the module front panel.

6. Identify a supported slot in the chassis. The following figure shows the symbols that

indicate the slot types.

Figure 2. Chassis Compatibility Symbols

NI PXIe-1062Q

12 3 45

1. PXI Express System Controller Slot

2. PXI Peripheral Slot

3. PXI Express Hybrid Peripheral Slot

4. PXI Express System Timing Slot

5. PXI Express Peripheral Slot

PXIe-5433 modules can be placed in PXI Express peripheral slots, PXI Express hybrid

peripheral slots, or PXI Express system timing slots.

7. Touch any metal part of the chassis to discharge static electricity.

8. Ensure that the ejector handle is in the downward (unlatched) position.

9. Place the module edges into the module guides at the top and bottom of the chassis. Slide

the module into the slot until it is fully inserted.

PXIe-5433 Getting Started Guide | © National Instruments | 5

Figure 3. Module Installation

NI PXIe-1075

1. Chassis

2. Hardware Module

3. Ejector Handle in Downward (Unlatched) Position

10. Latch the module in place by pulling up on the ejector handle.

11. Secure the module front panel to the chassis using the front-panel mounting screws.

Note Tightening the top and bottom mounting screws increases mechanical

stability and also electrically connects the front panel to the chassis, which can

improve the signal quality and electromagnetic performance.

12. Cover all empty slots using EMC filler panels or fill using slot blockers to maximize

cooling air flow, depending on your application.

13. Power on the chassis.

Related Information

Why Is the ACCESS LED Off When the Chassis Is On? on page 14

PXIe-5433 Pinout and LEDs

Front Panel

Refer to the following figure and tables for information about the one- and two-channel

PXIe-5433 front panel connectors and LEDs.

6| ni.com | PXIe-5433 Getting Started Guide

PXIe-5433

80 MHz 16-Bit AWG

ACCESS ACTIVE

CH 0

PFI 1

PFI 0

AUX 0

+5V MAX

PXIe-5433

80 MHz 16-Bit AWG

ACCESS ACTIVE

CH 0

CH 1

PFI 1

PFI 0

AUX 0

+5V MAX

Table 1. PXIe-5433 Signal Descriptions

Signal Connector

Type

Access Description

1 CH 0 SMA Output Generates waveforms from an analog output

terminal.

2 CH 1

3 PFI 0 Input/Output Imports digital trigger signals and exports

digital event signals. Imported digital trigger

signals can start or step through waveform

generation, and exported event signals indicate

the state of the generation engine.

4 PFI 1

5 AUX 0 MHDMR Routes digital trigger and event signals with

eight bidirectional PFI lines and provides a

+3.3 V power source.

The ACCESS LED indicates basic hardware status.

PXIe-5433 Getting Started Guide | © National Instruments | 7

Table 2. PXIe-5433 ACCESS LED Indicators

LED Color Indication

6 No color (off) The PXIe-5433 is not yet functional.

Amber The PXIe-5433 is being accessed.

Green The PXIe-5433 is ready to be programmed by NI-FGEN.

The ACTIVE LED indicates the PXIe-5433 hardware state.

Table 3. PXIe-5433 ACTIVE LED Indicators

LED Color Indication

7 No color (off) The PXIe-5433 is not generating.

Amber The PXIe-5433 is armed and waiting for a trigger.

Green The PXIe-5433 has received a trigger and is generating a waveform.

Red The PXIe-5433 has detected an error. NI-FGEN must access the

PXIe-5433 to determine the cause of the error. The LED remains red until

the error condition is removed. Example errors include the following:

• Phase-locked loop (PLL) unlocked: The PXIe-5433 has detected an

unlocked condition on a previously locked PLL. A PLL that is

unlocked while in reset does not show an error.

• The PXIe-5433 has powered down because the internal temperature

exceeded the maximum limit. The over-temperature condition must

be corrected and the hardware reset. To reset the hardware, call

niFgen Reset Device or niFgen_ResetDevice.1

AUX 0 Connector

Note The AUX 0 connector accepts a standard, third-party HDMI™ type C cable,

but the AUX 0 port is not an HDMI interface and the specified performance of the

AUX 0 connector is not guaranteed if a third-party HDMI cable is used. Use NI

cable assembly SHH19-MH19-AUX for all AUX 0 connections. Do not connect the

AUX 0 port on the PXIe-5433 to the HDMI port of another device. NI is not liable

for any damage resulting from such signal connections.

Refer to the following figure and table for information about the PXIe-5433 AUX 0 connector

pins.

1For more information about keeping the PXIe-5433 within internal temperature limits, refer to the

Maintain Forced-Air Cooling Note to Users included with your PXIe-5433 and at ni.com.

8| ni.com | PXIe-5433 Getting Started Guide

Table 4. AUX 0 Pin Signal Descriptions

Pin Signal Description

1 GND Ground reference for signals

2 NC No connection

3 GND Ground reference for signals

4 GND Ground reference for signals

5 NC No connection

6 GND Ground reference for signals

7 GND Ground reference for signals

8 AUX 0/PFI 0 Bidirectional PFI line

9 AUX 0/PFI 1 Bidirectional PFI line

10 GND Ground reference for signals

11 AUX 0/PFI 2 Bidirectional PFI line

12 AUX 0/PFI 3 Bidirectional PFI line

13 GND Ground reference for signals

14 AUX 0/PFI 4 Bidirectional PFI line

PXIe-5433 Getting Started Guide | © National Instruments | 9

Table 4. AUX 0 Pin Signal Descriptions (Continued)

Pin Signal Description

15 AUX 0/PFI 5 Bidirectional PFI line

16 AUX 0/PFI 6 Bidirectional PFI line

17 AUX 0/PFI 7 Bidirectional PFI line

18 +3.3 V +3.3 V power output (200 mA maximum)

19 GND Ground reference for signals

PXIe-5433 SCB-19 Pinout

NI recommends using the SCB-19 connector block to connect digital signals to the AUX 0

connector on the PXIe-5433 front panel. Refer to the following figure and table for

information about the SCB-19 signals when connected to the AUX 0 front panel connector.

1 2 3 4 5 6 7 8 9 10

14 15 16 17 18 19 20 21 22 23

11 12 13

24 25 26

Table 5. SCB-19 Signal Descriptions

Pin Signal Description

1 PFI 0 Bidirectional PFI line

2 PFI 1 Bidirectional PFI line

3 PFI 2 Bidirectional PFI line

4 PFI 3 Bidirectional PFI line

5 NC No connection

6 NC No connection

7 NC No connection

10 | ni.com | PXIe-5433 Getting Started Guide

Tabla de contenidos

Otros manuales de Equipo de prueba de National Instruments

National Instruments

National Instruments Module SCXI-1125 Manual

National Instruments

National Instruments NI PXI-5124 Manual de usuario

National Instruments

National Instruments GPIB Device Simulator EPROM Manual del propietario

National Instruments

National Instruments VirtualBench Manual de usuario

National Instruments

National Instruments PXIe-5172 Manual

National Instruments

National Instruments PXIe-5423 Manual de usuario

National Instruments

National Instruments ATE Core Configurations Manual de usuario

National Instruments

National Instruments SMB-2145 Manual de usuario

National Instruments

National Instruments NI PXI-5105 Manual

National Instruments

National Instruments ECUTS-16000 Manual de usuario

National Instruments

National Instruments PXIe-5164 Manual de usuario

National Instruments

National Instruments VirtualBench VB-8054 Manual del propietario

National Instruments

National Instruments USB Digitizers NI USB-5132 Manual de usuario

National Instruments

National Instruments PXI-5671 Manual de usuario

National Instruments

National Instruments PXIe-5185 Manual de usuario

National Instruments

National Instruments PXI-5670 Manual de usuario

National Instruments

National Instruments PXIe-5172 Manual de usuario

National Instruments

National Instruments SCXI-116 Series Manual de usuario

National Instruments

National Instruments PXIe-5163 Manual de usuario

National Instruments

National Instruments NI PXI-5922 Manual de usuario

National Instruments

National Instruments PCI-5153 Manual de usuario

National Instruments

National Instruments NI PCI-5122 Manual

National Instruments

National Instruments NI PXI-2567 Manual del propietario

National Instruments

National Instruments 5401 Manual de usuario

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Agilent Technologies

Agilent Technologies BERT Serial Manual de usuario

Agilent Technologies

Agilent Technologies N3280A Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario