National Instruments GPIB Device Simulator EPROM Manual del propietario
© Copyright 1993 National Instruments Corporation.
All Rights Reserved.
LabVIEW®is a trademark of National Instruments Corporation.
Product and company names are trademarks or trade names of their respective companies.
GPIB Device Simulator EPROM
Programming Manual
November 1993 Edition
Part Number 320638-01
National Instruments Corporate Headquarters
6504 Bridge Point Parkway
Austin, TX 78730-5039
(512) 794-0100
(800) IEEE-488 (toll-free U.S. and Canada)
Technical support fax: (512) 794-5678
Branch Offices:
Australia 03 879 9422, Austria 0662 435986, Belgium 02 757 00 20,
Canada (Ontario) 519 622 9310, Canada (Québec) 514 694 8521,
Denmark 45 76 26 00, Finland 90 527 2321, France 1 48 65 33 70,
Germany 089 714 50 93, Italy 02 48301892, Japan 03 3788 1921,
Netherlands 01720 45761, Norway 03 846866, Spain 91 640 0085,
Sweden 08 730 49 70, Switzerland 056 27 00 20, U.K. 0635 523545
© National Instruments Corp. iii GPIB Device Simulator EPROM
Contents
GPIB Device Simulator EPROM..............................................................1
Setting the Address.....................................................................1
Data Formats.............................................................................................2
Waveform Format.......................................................................2
Floating-Point Number Format...................................................2
Simulator Commands................................................................................2
Address Command .....................................................................2
Waveform Format Commands ...................................................3
Waveform Generation Commands .............................................4
Waveform Query Commands.....................................................4
"Multimeter Configuration" Commands ....................................5
Other Commands ........................................................................6
Command Summary .................................................................................8
Compatibility Commands .........................................................................9
LabVIEW®Examples...............................................................................10
LabWindows®Examples..........................................................................15
Figures
Figure 1. GPIB Device Simulator Set to Address 3 .............................1
Figure 2. Three ESR Bits Set by the Simulator ....................................6
© National Instruments Corp. 1 GPIB Device Simulator EPROM
GPIB Device Simulator EPROM
You can simulate the operation of a GPIB instrument by replacing the
EPROM inside a GPIB-232CT with the GPIB Device Simulator EPROM
(part number 702295-01). The GPIB-232CT will then act as a GPIB
instrument.
The Simulator functions like a GPIB oscilloscope in that it is capable of
returning waveforms in different configurations: ASCII, 8-bit unsigned
binary, and 16-bit signed binary. It is also capable of returning single values
in ASCII such as those returned by a multimeter.
Setting the Address
The default address of the GPIB Device Simulator EPROM is set using the
first five switches of the U20 dip switch inside the GPIB-232CT. All other
switch settings are ignored.
The first 5 switches set the address. Switch 1 is the least significant bit
(LSB) and switch 5 is the most significant bit (MSB). Figure 1 shows an
example of the Simulator set to address 3.
OFF
12345678
U20
LSB MSB
Figure 1. GPIB Device Simulator Set to Address 3
You change the address using the dip switches or by the sending the
Simulator the SADDR primary, secondary command. For example,
SADDR 1 sets the Simulator to address 1, and SADDR 2, 4sets the
Simulator to primary address 2 and secondary address 4.
GPIB Device Simulator EPROM 2 © National Instruments Corp.
Data Formats
Waveform Format
The Simulator returns a 128 point waveform in either ASCII or binary.
ASCII waveforms are preceded by the header CURVE. Binary waveforms
are preceded by a pound sign (#) and the number of bytes that are in the
waveform. All waveforms are terminated by a line feed <LF> character.
Floating Point ASCII (Default)
CURVE<space>num0,num1,...,num127<LF>
8-bit Unsigned Binary
#3128<Byte 0><Byte 1>...Byte<127><LF>
16-bit Signed Binary
#3256<MSB 0><LSB 0><MSB 1><LSB 1>...<MSB 127><LSB
127><LF>
Floating-Point Number Format
[+][-]1.2345E[+][-]0
Simulator Commands
The Simulator uses SCPI-like commands. The commands are shown in long
form; however, the Simulator only accepts the short form of the command.
In other words, only send the part of the command that is in uppercase
characters. You can send multiple commands to the Simulator by separating
them with a semicolon (;).
Address Command
SADDRess primary, secondary Sets the address (power-on
default – switch setting)
Example:SADDR 2 Set the address to 2
SADDR 3, 4 Set the primary address to 3
and the secondary address to 4
© National Instruments Corp. 3 GPIB Device Simulator EPROM
Waveform Format Commands
These commands format how the waveform data is returned by the
Simulator.
FORMat:DATA ASCii Floating point (Default)
INTeger,8 8-bit unsigned binary
INTeger,16 16-bit signed binary
FORMat:DATA? Returns the current waveform format
The following command changes the order of the bytes returned by
INTeger,16 encoding.
FORMat:BORDer NORMal Low byte first (Default)
SWAPped High byte first
FORMat:BORDer? Returns the current format of
the byte order
Example:FORM:DATA INT,16 Set the waveform format as
16-bit integers
FORM:DATA? Query the current waveform format.
For example, if the command was
issued after the preceding command, it
would return
FORM:DATA INT,16<LF>
GPIB Device Simulator EPROM 4 © National Instruments Corp.
Waveform Generation Commands
These commands generate a 128 point waveform of the specified type. The
number of cycles in the waveform is random. It can take 5 to 15 seconds to
generate the waveform depending on the format and type of the waveform.
Typically ASCII waveforms take longer than integer waveforms.
SOURce:FUNCtion SINusoid Sine waveform (Default)
SQUare Square waveform
NOISe Noisy sine waveform
RANDom Random noise waveform
PCHirp Chirp waveform
SOURce:FUNCtion? Returns the current
waveform type
Example: SOUR:FUNC SIN Generate a sinusoid waveform
SOUR:FUNC? Query the current waveform
type. For example, if the
command was issued after the
preceding command, it would
return SOUR:FUNC SIN<LF>
Waveform Query Commands
SENSe:DATA? Returns the waveform data in the
format specified by the waveform
format commands
SENSe:VOLTage:RANGe:OFFSet?Returns the Y offset for the
waveform in ASCII floating point
SENSe:VOLTage:RANGe? Returns the Y multiplier for the
waveform in ASCII floating point
SENSe:SWEep:TIME? Returns the X increment (1E-3) in
ASCII floating point
© National Instruments Corp. 5 GPIB Device Simulator EPROM
SENSe:VOLTage:HEADer? Returns all of the waveform
scaling information in the format
OFFSET=x.xxxxE+x,
RANGE=x.xxxxE+x,
TIME=1E-3<LF>
For integer-formatted waveforms, the offset and range is used to scale the raw
integer data–for example,
scaled.point(i) =(waveform.point(i) +offset) *range
Example:SENS:DATA? Query Simulator for the
waveform
SENS:VOLT:HEAD? Query Simulator for the
waveform scaling information
"Multimeter Configuration" Commands
These commands simulate the operation of a meter. They return one value
in ASCII floating point.
MEASure:DC? Returns a random value between
0 to +x in floating point ASCII.
The range of x depends on the
CONFigure:DC command
CONFigure:DC DEFault MEASure:DC? returns a number
between 0 and 10
MIN MEASure:DC? returns a number
between 0 and 1
MAX MEASure:DC? returns a number
between 0 and 100
CONFigure:DC? Returns the current configuration
setting
Example:CONF:DC MAX Set the maximum range
CONF:DC? Query the current DC range. For
example, if the command was
issued after the command above,
it would return
CONF:DC MAX<LF>
MEAS:DC? Queries one value, for example
1.2308<LF>
GPIB Device Simulator EPROM 6 © National Instruments Corp.
Other Commands
*IDN? Returns National Instruments
GPIB Device Simulator Rev
A.x <LF>
*RST Resets the Simulator to its default state
*TRG Triggers the Simulator and returns one
random reading (same as MEAS:DC?)
*TST? Simulates testing the Simulator.
Returns OK
*OPC Sets the operation complete bit in the
Standard Event Status Register (ESR)
*OPC? Returns the value of the OPC bit in the
ESR register
*ESR? Returns value of Standard Event Status
register as specified by FORM:SREG
Figure 2 illustrates the bits defined by the Simulator for the ESR register–
bit 7 (Power On), bit 5 (Command Error), and bit 0 (Operation Complete).
Bit 7 is set when the Simulator is powered on; bit 5 is set when the
Simulator receives an invalid command; and, bit 0 is set when the
Simulator receives the *OPC command. You can use the *ESR?
command to query the value of the ESR register. The value returned is in
either ASCII or HEX, as specified by the FORMat:SREGister
command. The ESR register is cleared after you read it.
12345670
Power On
Comm
a
Figure 2. Three ESR Bits Set by the Simulator
© National Instruments Corp. 7 GPIB Device Simulator EPROM
*ESE 0x## Sets value of Standard Event Status
(zero, x, mask in hex) Enable register
*ESE? Returns value of Standard Event Status
Enable register as specified by
FORM:SREG
*STB? Returns value of Status Byte register as
specified by FORM:SREG
*SRE 0x## Sets value of Service Request Enable
(zero, x, mask in hex) register
*SRE? Returns value of Service Request Enable
register as specified by FORM:SREG
*WAI Does not do anything; included to make
the Simulator IEEE 488.2 compatible
FORMat:SREGister ASCii Specifies the output of ESR, ESE, STB,
and SRE registers as an ASCII string
(default)
HEX Specifies the output of ESR, ESE, STB,
and SRE registers in hex
FORMat:SREGister? Returns the current format of the registers
SYStem:HELP? Returns a list of all of the commands.
Refer to Command Summary section.
Tabla de contenidos
Otros manuales de Equipo de prueba de National Instruments
National Instruments
National Instruments USB Digitizers NI USB-5132 Manual de usuario
National Instruments
National Instruments NI PXI-5105 Manual
National Instruments
National Instruments USRP-29 Series Manual de usuario
National Instruments
National Instruments PXI-5154 Manual de usuario
National Instruments
National Instruments ECUTS-16000 Manual de usuario
National Instruments
National Instruments PCI-5153 Manual de usuario
National Instruments
National Instruments NI PXI-5124 Manual de usuario
National Instruments
National Instruments PXI-5671 Manual de usuario
National Instruments
National Instruments PXIe-5433 Manual de usuario
National Instruments
National Instruments ATE Core Configurations Manual de usuario
National Instruments
National Instruments Module SCXI-1125 Manual
National Instruments
National Instruments NI PXI-5922 Manual de usuario
National Instruments
National Instruments PXIe-5423 Manual de usuario
National Instruments
National Instruments NI SCB-68A Manual de usuario
National Instruments
National Instruments VirtualBench Manual de usuario
National Instruments
National Instruments NI PXIe-5171R Manual
National Instruments
National Instruments NI PCI-5122 Manual
National Instruments
National Instruments NI PXIe-1078 Manual de usuario
National Instruments
National Instruments PXIe-5172 Manual de usuario
National Instruments
National Instruments 5401 Manual de usuario
Manuales populares de Equipo de prueba de otras marcas
SMART
SMART KANAAD SBT XTREME 3G Series Manual de usuario
Agilent Technologies
Agilent Technologies BERT Serial Manual de usuario
Agilent Technologies
Agilent Technologies N3280A Manual de usuario
Vernier
Vernier Go Direct Voltage Manual de usuario
Lifeloc
Lifeloc R.A.D.A.R. Manual de usuario
Fluke
Fluke T5-600 Instrucciones de funcionamiento e instalación
