National Instruments NI USB-9219 Manual de usuario

USER GUIDE AND SPECIFICATIONS

NI USB-9219

4-Channel, 24-Bit, Universal Analog Input Module

This user guide describes how to use the National Instruments USB-9219

and lists the device specifications.

Introduction

The NI USB-9219 provides a USB interface for four channels of universal

analog input with integrated signal conditioning. The NI USB-9219

consists of two components: an NI 9219 module, and an NI USB-9162

carrier, as shown in Figure 1.

Figure 1. NI USB-9219 Components

NI 9219

NI USB-9162

NI USB-9219

Hi-SPeed USB Carrier

NI USB-9162

Hi-Speed USB Carrier

NI USB-9162

NI USB-9219 User Guide and Specifications 2 ni.com

Dimensions

Figure 2 shows the NI USB-9219 device dimensions.

Figure 2. NI USB-9219 Device in Millimeters (Inches)

Safety Guidelines

Operate the NI USB-9219 only as described in these operating instructions.

Hot Surface This icon denotes that the component may be hot. Touching this component

may result in bodily injury.

Safety Guidelines for Hazardous Voltages

If hazardous voltages are connected to the module, take the following

precautions. A hazardous voltage is a voltage greater than 42.4 Vpk or

60 VDC to earth ground.

Caution Ensure that hazardous voltage wiring is performed only by qualified personnel

adhering to local electrical standards.

Caution Do not mix hazardous voltage circuits and human-accessible circuits on the same

module.

Caution Make sure that devices and circuits connected to the module are properly

insulated from human contact.

Hi-Speed USB Carrier

NI USB-9162

120.68 mm

(4.751 in.)

118.26 mm

(4.656 in.)

88.12 mm

(3.469 in.)

25.34 mm

(0.998 in.)

©National Instruments Corporation 3 NI USB-9219 User Guide and Specifications

Caution When module terminals are hazardous voltage LIVE (>42.4 Vpk/60 VDC), you

must ensure that devices and circuits connected to the module are properly insulated from

human contact. You must use the NI 9972 connector backshell kit, as illustrated in Figure 3

to ensure that the terminals are not accessible.

Figure 3. NI 9972 Connector Backshell

Related Documentation

Each application software package and driver includes information about

writing applications for taking measurements and controlling measurement

devices. The following references to documents assume you have

NI-DAQmx 8.7 or later, and where applicable, version 7.1 or later of the

NI application software.

NI-DAQmx for Windows

The DAQ Getting Started Guide describes how to install your NI-DAQmx

for Windows software, your NI-DAQmx-supported DAQ device, and

how to confirm that your device is operating properly. Select Start»

All Programs»National Instruments»NI-DAQ»DAQ Getting Started

Guide.

The NI-DAQ Readme lists which devices are supported by this version of

NI-DAQ. Select Start»All Programs»National Instruments»NI-DAQ»

NI-DAQ Readme.

The NI-DAQmx Help contains general information about measurement

concepts, key NI-DAQmx concepts, and common applications that

are applicable to all programming environments. Select Start»

All Programs»National Instruments»NI-DAQ»NI-DAQmx Help.

NI USB-9219 User Guide and Specifications 4 ni.com

LabVIEW

If you are a new user, use the Getting Started with LabVIEW manual to

familiarize yourself with the LabVIEW graphical programming

environment and the basic LabVIEW features you use to build data

acquisition and instrument control applications. Open the Getting Started

with LabVIEW manual by selecting Start»All Programs»National

Instruments»LabVIEW»LabVIEW Manuals or by navigating to the

labview\manuals directory and opening LV_Getting_Started.pdf.

Use the LabVIEW Help, available by selecting Help»Search the

LabVIEW Help in LabVIEW, to access information about LabVIEW

programming concepts, step-by-step instructions for using LabVIEW, and

reference information about LabVIEW VIs, functions, palettes, menus, and

tools. Refer to the following locations on the Contents tab of the LabVIEW

Help for information about NI-DAQmx:

•Getting Started»Getting Started with DAQ—Includes overview

information and a tutorial to learn how to take an NI-DAQmx

measurement in LabVIEW using the DAQ Assistant.

•VI and Function Reference»Measurement I/O VIs and

Functions—Describes the LabVIEW NI-DAQmx VIs and properties.

•Taking Measurements—Contains the conceptual and how-to

information you need to acquire and analyze measurement data

in LabVIEW, including common measurements, measurement

fundamentals, NI-DAQmx key concepts, and device considerations.

LabWindows/CVI

The Data Acquisition book of the LabWindows/CVI Help contains

measurement concepts for NI-DAQmx. This book also contains Taking an

NI-DAQmx Measurement in LabWindows/CVI, which includes

step-by-step instructions about creating a measurement task using the DAQ

Assistant. In LabWindows™/CVI™, select Help»Contents, then select

Using LabWindows/CVI»Data Acquisition.

The NI-DAQmx Library book of the LabWindows/CVI Help contains

API overviews and function reference for NI-DAQmx. Select Library

Reference»NI-DAQmx Library in the LabWindows/CVI Help.

Measurement Studio

If you program your NI-DAQmx-supported device in Measurement Studio

using Visual C++, Visual C#, or Visual Basic .NET, you can interactively

create channels and tasks by launching the DAQ Assistant from MAX or

from within Visual Studio .NET. You can generate the configuration code

based on your task or channel in Measurement Studio. Refer to the DAQ

Assistant Help for additional information about generating code. You also

©National Instruments Corporation 5 NI USB-9219 User Guide and Specifications

can create channels and tasks, and write your own applications in your

ADE using the NI-DAQmx API.

For help with NI-DAQmx methods and properties, refer to the NI-DAQmx

.NET Class Library or the NI-DAQmx Visual C++ Class Library included

in the NI Measurement Studio Help. For general help with programming in

Measurement Studio, refer to the NI Measurement Studio Help, which is

fully integrated with the Microsoft Visual Studio .NET help. To view

this help file in Visual Studio. NET, select Measurement Studio»

NI Measurement Studio Help.

To create an application in Visual C++, Visual C#, or Visual Basic .NET,

follow these general steps:

1. In Visual Studio .NET, select File»New»Project to launch the New

Project dialog box.

2. Find the Measurement Studio folder for the language you want to

create a program in.

3. Choose a project type. You add DAQ tasks as a part of this step.

ANSI C without NI Application Software

The NI-DAQmx Help contains API overviews and general information

about measurement concepts. Select Start»All Programs»National

Instruments»NI-DAQ»NI-DAQmx Help.

The NI-DAQmx C Reference Help describes the NI-DAQmx Library

functions, which you can use with National Instruments data acquisition

devices to develop instrumentation, acquisition, and control applications.

Select Start»All Programs»National Instruments»NI-DAQ»

NI-DAQmx C Reference Help.

.NET Languages without NI Application Software

With the Microsoft .NET Framework version 1.1 or later, you can use

NI-DAQmx to create applications using Visual C# and Visual Basic .NET

without Measurement Studio. You need Microsoft Visual Studio .NET

2003 or Microsoft Visual Studio 2005 for the API documentation to be

installed.

The installed documentation contains the NI-DAQmx API overview,

measurement tasks and concepts, and function reference. This help is fully

integrated into the Visual Studio .NET documentation. To view the

NI-DAQmx .NET documentation, go to Start»Programs»National

Instruments»NI-DAQ»NI-DAQmx .NET Reference Help. Expand

NI Measurement Studio Help»NI Measurement Studio .NET Class

Library»Reference to view the function reference. Expand

NI Measurement Studio Help»NI Measurement Studio .NET Class

NI USB-9219 User Guide and Specifications 6 ni.com

Library»Using the Measurement Studio .NET Class Libraries to view

conceptual topics for using NI-DAQmx with Visual C# and Visual

Basic .NET.

To get to the same help topics from within Visual Studio, go to Help»

Contents. Select Measurement Studio from the Filtered By drop-down

list and follow the previous instructions.

Device Documentation and Specifications

NI-DAQmx includes the Device Document Browser, which contains

online documentation for supported DAQ, SCXI, and switch devices, such

as help files describing device pinouts, features, and operation, and PDF

files of the printed device documents. You can find, view, and/or print the

documents for each device using the Device Document Browser at any

time by inserting the CD. After installing the Device Document Browser,

device documents are accessible from Start»All Programs»National

Instruments»NI-DAQ»Browse Device Documentation.

Note You can also download these documents at ni.com/manuals.

Training Courses

If you need more help getting started developing an application with

NI products, NI offers training courses. To enroll in a course or obtain

a detailed course outline, refer to ni.com/training.

Technical Support on the Web

For additional support, refer to ni.com/support or zone.ni.com.

Installing the Software

Software support for the NI USB-9219 for Vista/XP/2000 is provided by

NI-DAQmx. The DAQ Getting Started Guide, which you can download at

ni.com/manuals, offers NI-DAQmx users step-by-step instructions for

installing software and hardware, configuring channels and tasks, and

getting started developing an application.

Installing Other Software

If you are using other software, refer to the installation instructions that

accompany your software.

©National Instruments Corporation 7 NI USB-9219 User Guide and Specifications

Example Programs

The NI-DAQmx CD contains example programs that you can use to get

started programming with the NI USB-9219. Refer to the NI-DAQmx for

USB Devices Getting Started Guide that shipped with your device, and

is also accessible from Start»All Programs»National Instruments»

NI-DAQ, for more information.

Installing the NI USB-9219 Device

Before installing the device, you must install the software you plan to use

with the device. Refer to the Installing the Software section of this guide

and the documentation included with the software for more information.

Installing the NI USB-9219 Device into the NI USB-9162 Carrier

The NI USB-9219 module and NI USB-9162 carrier are packaged

separately. Refer to Figure 4, while completing the following assembly

steps:

1. Make sure that no signals are connected to the NI USB-9219 module

and the USB cable is not connected to the device.

2. Remove the protective cover from the 15-pin D-SUB connector.

3. Align the I/O module with the carrier, as shown in Figure 4.

Figure 4. Module Installation

4. Squeeze the latches and insert the NI USB-9219 module into the

NI USB-9162 carrier.

NI USB-9219 User Guide and Specifications 8 ni.com

5. Press firmly on the connector side of the NI USB-9219 module until

the latches lock the module into place, as shown in Figure 5.

Figure 5. Locking Module into Place

6. Connect the USB cable to the assembled NI USB-9219.

Mounting the NI USB-9219 to a Panel

Threaded inserts are located in the NI USB-9219 for mounting it to a panel.

Refer to Figure 6 for dimensions.

Figure 6. Module Dimensions In Millimeters (Inches)

72.2 mm

(2.84 in.)

85.7 mm

(3.37 in.)

76.1 mm

(3.00 in.)

Threaded Insert

M3 x 0.5

8.5 mm (0.34 in.) Max Depth

©National Instruments Corporation 9 NI USB-9219 User Guide and Specifications

Connecting the NI USB-9219 to a Computer

Plug one end of the USB cable into the NI USB-9219 and the other end into

an available USB port on the computer. Refer to the NI-DAQmx for USB

Devices Getting Started Guide that shipped with your device, and is also

accessible from Start»All Programs»National Instruments»NI-DAQ,

for more information.

LED Indicator

The NI USB-9219 device has a green LED next to the USB connector. The

LED indicator indicates device status, as listed in Table 1. When the device

is connected to a USB port, the LED blinks steadily to indicate that the

device is initialized and is receiving power from the connection.

If the LED is not blinking, it may mean that the device is not initialized or

the computer is in standby mode. In order for the device to be recognized,

the device must be connected to a computer that has NI-DAQmx installed

on it. If your device is not blinking, make sure your computer has the latest

version of NI-DAQmx installed on it, and the computer is not in standby

mode.

Table 1. LED State/Device Status

LED State Device Status

Not lit Device not connected or in suspend.

On, not blinking Device connected, but no module installed.

Single-blink Operating normally.

Double-blink Operating normally.

Quadruple-blink Device error. Refer to ni.com/support.

NI USB-9219 User Guide and Specifications 10 ni.com

Wiring the NI USB-9219 Device

Caution A high voltage screw terminal backshell must be installed when using hazardous

voltages (>42.4 Vpk, 60 VDC).

Note Table 2 illustrates the accessories available from ni.com for use with the

NI USB-9219.

The NI USB-9219 has four 6-terminal connectors that provide connections

for four analog input channels. Connect the positive signal of the signal

source to the positive input signal terminal (HI) and the negative signal of

the signal source to the negative input signal terminal (LO). Use the

excitation terminals if your sensor requires a separate excitation

connection. Refer to Table 3 for the signal names and Table 4 for the

terminal assignments for each mode. Refer to the NI USB-9219 Circuitry

section for information about connections in each mode.

Table 2. Accessories

Accessory Accessory Description

NI 9972 Strain relief for 6-position spring terminal

NI 9973 6-position connectors

Table 3. Signal Names

Module Terminal Signal Name Signal Description

1T+ TEDS Data

2T– TEDS COM

3EX+/HI*Positive excitation or input

signal

4HI Positive input signal

5EX–/LO*Negative excitation or input

signal

6LO Negative input signal

*Depending on the mode, terminals 3 and 5 are either the excitation signals or the input signals.

Ch 0

Ch 1

Ch 2

Ch 3

Tabla de contenidos

Otros manuales de Sistema de E/S de National Instruments

National Instruments

National Instruments R Series Manual de usuario

National Instruments

National Instruments 9242 Manual de usuario

National Instruments

National Instruments NI 9226 Manual de usuario

National Instruments

National Instruments NI-9244 Manual de usuario

National Instruments

National Instruments sbRIO-9218 Manual de usuario

National Instruments

National Instruments PXIe-4340 Manual

National Instruments

National Instruments NI 9269 Manual

National Instruments

National Instruments PXIe-4322 Manual

National Instruments

National Instruments SCC-CI20 Manual de usuario

National Instruments

National Instruments SCXI-1162HV Manual de usuario

National Instruments

National Instruments NI 6738 Manual

National Instruments

National Instruments NI 9226 Manual

National Instruments

National Instruments SCXI-1121 Manual

National Instruments

National Instruments NI-9228 Manual

National Instruments

National Instruments DAQCard-6533 Manual de usuario

National Instruments

National Instruments IMAQ SCB-100 Manual de usuario

National Instruments

National Instruments 776570-00 Manual de usuario

National Instruments

National Instruments FieldPoint FP-AI-100 Manual de usuario

National Instruments

National Instruments NI 9231 Manual

National Instruments

National Instruments SC Express PXIe-4309 Manual de usuario

National Instruments

National Instruments NI VISION PCI-8254R Manual de usuario

National Instruments

National Instruments FieldPoint FP-DI-330 Manual de usuario

National Instruments

National Instruments PXI-6070E Manual de usuario

National Instruments

National Instruments SCXI-1104 Manual de usuario

Manuales populares de Sistema de E/S de otras marcas

WAGO

WAGO 750-344 Manual de usuario

Teknim

Teknim TWM-1887 Manual de instrucciones

Intelligent Appliance

Intelligent Appliance IA-2662-E Manual de usuario

BERGHOF

BERGHOF ECC DIO 16/16 Manual de instrucciones

Advantech

Advantech PCM-27J3AU Manual de instalación y operación

Festo

Festo CP-E08-M12-CL Manual de usuario

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manual de usuario

Hitachi

Hitachi HX-RIO3 Series Manual de usuario

NUUO

NUUO SCB-A08 Manual de usuario

M-system

M-system R3Y-RS8 Manual de usuario

jablotron

jablotron JB-110N Manual de usuario

Omron

Omron SYSMAC C200H Manual de usuario

DOLD

DOLD SAFEMASTER M Manual de usuario

ABB

ABB OPT-MF-001 Manual de usuario

Omron

Omron SYSMAC C2000H Manual de usuario

Helmholz

Helmholz TB20 Manual de usuario

ICP DAS USA

ICP DAS USA tM-AD2 Manual de usuario

Automationdirect.com

Automationdirect.com DL305 Manual de usuario