National Instruments PXI-8232 Manual de usuario

INSTALLATION GUIDE

NI PXI-8232

This document explains how to install the Ethernet and NI-488.2 drivers for

your NI PXI-8232 (part number 189140x-02L, where xis D or higher).

The Ethernet port on the NI PXI-8232 is based on the

Intel 82541PI-compatible Ethernet controller.

Installing Your PXI Board

Complete the following steps to install the PXI-8232 hardware:

1. Shut down Windows, if it is running, by selecting Start»Shut Down.

2. Power off your PXI or CompactPCI chassis. Keep the chassis plugged

in so it remains grounded as you install the adapter.

3. Remove the filler panel from a PXI peripheral bus master slot. The

adapter requires a bus master slot to take advantage of the onboard

DMA and Ethernet controllers. All PXI chassis and most CompactPCI

chassis contain only bus master slots. Refer to your chassis

documentation to verify you are using a bus master slot.

4. Touch a metal part on your chassis to discharge any static electricity

that might be on your clothes or body.

5. Insert the adapter into the selected bus master slot. Use the

injector/ejector handle to fully inject the device into place.

6. Screw the adapter front panel to the PXI or CompactPCI chassis front

panel mounting rail.

NI PXI-8232 Installation Guide 2 ni.com

Connect the Network Cable

Connect a network cable to the adapter, as shown in the following figure.

• For 1000BaseT (gigabit over copper), use Category 5 (must be 4-pair

wiring). Be sure to use Category 5 cable that complies with the

TIA-568 wiring specification. For more information on this

specification, refer to the Telecommunications Industry Association

Web site, www.tiaonline.org.

• For 100BaseTX, use Category 5 wiring or better.

Caution If using less than 4-pair cabling, you must manually configure the adapter and

link partner speed and duplex setting. In addition, with 2- and 3-pair cabling, the adapter

can achieve speeds of up to only 100 MB/s.

• For 10BaseT, use Category 3 wiring or better.

• To use this adapter in a residential environment (at any speed), use

Category 5 wiring. If the cable runs between rooms or through walls

and/or ceilings, it should be plenum rated for fire safety.

• The cable length is limited to 100 m.

• The adapter must be connected to a compatible link partner, preferably

set to auto-negotiate speed and duplex.

• The PXI-8232 automatically accommodates either MDI or MDI-X

connections. You can use the auto-MDI-X feature to connect two

adapters directly without using a crossover cable.

©National Instruments 3 NI PXI-8232 Installation Guide

Install the Drivers

Follow the installation instructions for your operating system. The adapter

works with the following operating systems:

• Windows XP and later

• LabVIEW Real-Time 2010 or higher

Windows XP and later

Complete the following steps to install the driver software for Windows XP

and later:

1. Insert the NI-488.2 media. The autorun launches to start the

installation process.

Tip The View Documentation link on the autorun screen provides access to NI-488.2

documentation, including detailed hardware installation instructions.

2. When you have completed the software installation, restart the

computer.

3. Install the Windows XP and later Ethernet drivers.

Note The NI-488.2 Hardware Installation utility may run at this time. Finish the Ethernet

installation described below before using the utility.

(Windows Vista and later) Windows automatically detects the new

hardware and installs the Ethernet driver.

(Windows XP and Server 2003) Cancel the Found New Hardware Wizard

and insert the PCI/PXI Gigabit Ethernet Adapters media. From the

media, launch the appropriate executable: PROWin32.exe for 32-bit

systems or PROWinx64.exe for 64-bit systems. Follow the

instructions to install the driver for your Ethernet port.

4. Use the NI-488.2 Hardware Installation utility.

LabVIEW Real-Time

LabVIEW Real-Time includes drivers for the Ethernet port on your

PXI-8232 board; no additional software is needed.

The GPIB interface requires additional software. Complete the following

steps to install the NI-488.2 software:

1. On the Windows host, insert the NI-488.2 media. The autorun launches

to start the installation process.

2. In the installation feature tree, ensure that the NI-488.2 for

LabVIEW Real-Time feature is selected to install.

NI PXI-8232 Installation Guide 4 ni.com

3. When you complete the software installation, restart the computer if

prompted.

4. In Measurement & Automation Explorer, deploy the software to your

target. Make sure that NI-488.2 is selected to be installed to your

target.

Troubleshooting

Adapter Cannot Connect to the Network

• Make sure the cable is installed properly.

The network cable must be installed properly at both the adapter and

hub. The maximum cable distance is 100 m. If the cable is connected

properly and within the allowed distance, try another cable.

• Check the LEDs on the adapter.

The adapter has two LEDs on the RJ-45 connector. The following table

lists the function of each LED.

• Verify that you are using the drivers that came with the adapter.

LED Color Function Indication Meaning

Green Action/Link On The adapter is receiving power. The cable

connection is good.

Off The adapter is not sending or receiving

network data. The adapter is not receiving

power. The cable connection is bad or you

have a driver problem.

Flashing The adapter is sending and receiving

network data.

Yellow/Green Speed Yellow The adapter is operating at 1000 Mb/s.

Green The adapter is operating at 100 Mb/s.

Off The adapter is operating at 10 Mb/s.

©National Instruments 5 NI PXI-8232 Installation Guide

Computer Hangs When Drivers Are Loaded

• Change the PCI BIOS interrupt settings. Refer to the PXI Installation

Tips section for more information.

Link LED Does Not Light

• Make sure the network drivers are loaded by checking the Driver tab

of the adapter’s Device Manager properties.

• Check the cable connection.

ACT LED Does Not Light

• Make sure the correct network drivers are loaded by checking the

Driver tab of the adapter’s Device Manager properties.

• The network may be idle.

Adapter Has Stopped Working

• Reseat the adapter in the PXI slot or try a different slot.

• The network drivers may be corrupt or missing. Remove and reinstall

the drivers.

• Reboot the computer.

• Use another cable.

• Use a different adapter.

Link LED Is Not Lit When Computer Is Shut Down and Power Is Connected

• Make sure the network cable is attached.

PXI Installation Tips

PXI computers are designed to configure add-in boards automatically each

time the computer starts. The PXI computer sets the I/O address and IRQ

level for the peripheral boards when the computer starts. The network

drivers cannot change these values. If you experience problems when the

computer starts, you may need to follow additional steps.

On some computers, manual configuration is possible through the

computer’s BIOS setup utility. Refer to the documentation for your

computer. You may need to verify or change some BIOS settings.

NI PXI-8232 Installation Guide 6 ni.com

The following common solutions may correct your problem:

• Make sure you have installed the adapter in a bus master-enabled slot.

On some computers, not all slots are bus master enabled by default.

Check your BIOS settings. Enable PXI bus mastering, if your BIOS

has such an option.

• Reserve interrupts (IRQ) and/or memory addresses for ISA adapters.

This prevents PXI boards from using the same settings ISA boards are

using. Try changing some of the interrupts reserved for ISA, but not

being used, to reserved for PXI.

• Update your BIOS. Sometimes updating the BIOS corrects some

configuration problems.

• Configure the PXI slot for level-triggered interrupts instead of

edge-triggered interrupts in BIOS.

Ethernet Adapter Specifications

LEDs

Green ...............................................Activity/Link

Yellow/Green ..................................Speed

Refer to ni.com/products for complete specifications.

LabVIEW, National Instruments, NI, ni.com, the National Instruments corporate logo, and the Eagle

logo are trademarks of National Instruments Corporation. Refer to the Trademark Information at

ni.com/trademarks for other National Instruments trademarks. Other product and company

names mentioned herein are trademarks or trade names of their respective companies. For patents

covering National Instruments products/technology, refer to the appropriate location: Help»Patents in

your software, the patents.txt file on your media, or the National Instruments Patents Notice at

ni.com/patents. Refer to the Export Compliance Information at ni.com/legal/

export-compliance for the National Instruments global trade compliance policy and how to

obtain relevant HTS codes, ECCNs, and other import/export data.

Tabla de contenidos

Otros manuales de Controladores de National Instruments

National Instruments

National Instruments cRIO-9075 Manual de usuario

National Instruments

National Instruments NI PXI-8104 Manual de usuario

National Instruments

National Instruments PXI-8195 Manual de usuario

National Instruments

National Instruments RMC-8356 Manual de usuario

National Instruments

National Instruments cRIO-9032 Manual de usuario

National Instruments

National Instruments GPIB-ENET Manual de usuario

National Instruments

National Instruments CMS-9068 Instrucciones de montaje

National Instruments

National Instruments PXI-8150B Manual de usuario

National Instruments

National Instruments FieldPoint cFP-20 Series Manual de usuario

National Instruments

National Instruments PXI Series Manual de usuario

National Instruments

National Instruments RMC-8354 Manual de usuario

National Instruments

National Instruments sbRIO-9607 Manual de usuario

National Instruments

National Instruments sbRIO-9637 Manual de usuario

National Instruments

National Instruments AT-GPIB/TNT Manual de usuario

National Instruments

National Instruments 7932 Manual de usuario

National Instruments

National Instruments NI 3100 Manual de usuario

National Instruments

National Instruments PXI-8195 Manual de usuario

National Instruments

National Instruments AT-GPIB/TNT Manual de usuario

National Instruments

National Instruments VXI Series Manual de usuario

National Instruments

National Instruments PXIe-8100 Manual de usuario

National Instruments

National Instruments GPIB-232CT-A IBCL EPROM Manual de usuario

National Instruments

National Instruments Two-Slot Embedded Controller NI PXI-8183 Manual de usuario

National Instruments

National Instruments NI cRIO-9065 Manual de usuario

National Instruments

National Instruments 73 Series Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario