National Instruments FieldPoint cFP-20 Series Manual de usuario

FieldPoint

1cFP-20xx Quick Start Guide

National Instruments Corporation

cFP-20

Quick Start Guide

What You Need

to Get Set Up

• cFP-20

LabVIEW RT controller

• Mounting hardware (DIN rail,

panel-mount, or rack-mount

accessory)

• I/O module(s)

• cFP-BP-

backplane, connector

blocks, cables

• 11–30 VDC power supply

• Accessories: Ethernet cable,

number 2 Phillips screwdriver

• PC running Windows

• FieldPoint software 3.0.2 or later

• LabVIEW RT

Mount the Compact FieldPoint Backplane

You can mount the cFP-BP-

backplane on a 35 mm DIN rail, on a panel, or in a

standard 19 in. rack. Before using any of these mounting methods, record the serial

number from the back of the backplane.

Each set of mounting instructions in this document includes an instruction to connect

the protective earth (PE) ground terminal on the cFP-BP-

backplane to the system

safety ground. The backplane PE ground terminal has the following symbol stamped

beside it: . Connect the backplane PE ground terminal to the system safety ground

using 14 AWG (1.6 mm) wire with a ring lug. Use the 5/16 in. panhead screw shipped

with the backplane to secure the ring lug to the backplane PE ground terminal.

323334c.qxd 4/3/2003 4:19 PM Page 1

cFP-20xx Quick Start Guide ni.com

CAUTION Keep in mind these requirements for space and cabling clearance:

•Allow at least 51 mm (2 in.) all around the backplane for air circulation.

•Allow 38 mm (1.5 in.) below and 51 mm (2 in.) above the controller for

cabling clearance.

Cabling

Clearance

4 slots = 246 mm (9.68 in.)

8 slots = 441 mm (17.4 in.)

Cooling Outline

51 mm (2 in.)

Cooling Outline

51 mm (2 in.)

Min. 182 mm (7.18 in.)

106 mm (4.18 in.)

Cabling

Clearance

Cooling Outline

51 mm (2 in.)

All Around

4 slots = 246 mm (9.68 in.)

8 slots = 441 mm (17.4 in.)

127 mm

(5.00 in.)

Min. 165 mm

(6.50 in.)

323334c.qxd 4/3/2003 4:19 PM Page 2

3cFP-20xx Quick Start Guide

National Instruments Corporation

Mounting the Backplane on a Panel

A. Fasten the panel-mount plates to the back of the cFP-BP-

using a number 2 Phillips

screwdriver and the 8-32 ×5/16 in. countersink screws shipped with the kit.

CAUTION Do not use screws longer than 5/16 in. to fasten the panel-mount

plates to the backplane.

NATIONAL

INSTRUMENTS

102 mm

(4 in.)

457 mm (18 in.)

323334c.qxd 4/3/2003 4:19 PM Page 3

cFP-20xx Quick Start Guide ni.com

260 mm (10.25 in.)

102 mm

(4 in.)

104.78 mm

(4.1 in.)

63.50 mm

(2.5 in.)

22.23 mm

(0.9 in.)

33.15 mm

(1.3 in.)

129.54 mm

(5.1 in.)

311.40 mm

(12.3 in.)

387.60 mm

(15.3 in.)

407.80 mm

(16.1 in.)

127.00 mm

(5.0 in.)

440.94 mm

(17.4 in.)

323334c.qxd 4/3/2003 4:19 PM Page 4

5cFP-20xx Quick Start Guide

National Instruments Corporation

B. Bolt or screw the panel-mount accessory to a panel.

C. Connect the PE ground terminal on the cFP-BP-

to safety ground.

CAUTION Disconnect power before removing the backplane from the panel.

Mounting the Backplane on a DIN Rail

NI recommends DIN rail mounting for the cFP-BP-4 only. Use panel mounting or rack

mounting for the cFP-BP-8. The DIN rail mounting kit is NI part number 778614-01

A. Fasten the DIN rail clip to the cFP-BP-4 using a number 2 Phillips screwdriver and

the 8-32 ×5/16 in. countersink screws shipped with the clip.

104.74 mm

(4.1 in.)

63.46 mm

(2.5 in.)

127.00 mm

(5.0 in.)

22.19 mm

(0.9 in.)

34.04 mm

(1.3 in.)

84.84 mm

(3.3 in.)

161.04 mm

(6.3 in.)

211.84 mm

(8.3 in.)

245.87 mm

(9.6 in.)

323334c.qxd 4/3/2003 4:19 PM Page 5

cFP-20xx Quick Start Guide ni.com

B. Insert one edge of the DIN rail into the deeper opening of the DIN rail clip.

C. Press down firmly on the backplane to compress the spring until the clip locks in

place on the DIN rail.

D. Connect the PE ground terminal on the cFP-BP-4 to safety ground.

CAUTION Disconnect power before removing the backplane from the DIN rail.

CAUTION Do not use screws longer than 5/16 in. to fasten the DIN rail clip to

the backplane.

NATIONAL

INSTRUMENTS

323334c.qxd 4/3/2003 4:19 PM Page 6

7cFP-20xx Quick Start Guide

National Instruments Corporation

Mounting the Backplane in a Standard 19-in. Rack

A. Fasten the rack-mount bracket to the back of the cFP-BP-

using the captive

screws on the bracket.

NATIONAL

INSTRUMENTS

323334c.qxd 4/3/2003 4:19 PM Page 7

cFP-20xx Quick Start Guide ni.com

B. Bolt the rack-mount accessory to a standard 19-in. rack.

C. Connect the PE ground terminal on the cFP-BP-

to safety ground.

NATIONAL

INSTRUMENTS

CAUTION Disconnect power before removing the backplane from the bracket.

323334c.qxd 4/3/2003 4:19 PM Page 8

9cFP-20xx Quick Start Guide

National Instruments Corporation

Install the cFP-20

Controller on the Backplane

A. Make sure that no power is connected to the controller.

B. Make sure that the cFP-20

controller is right side up with the NI logo at the top,

and align the captive screws on the controller with the holes on the backplane.

C. Seat the card edge at the back of the controller in the card-edge connector on the

backplane.

D. Press the controller firmly to seat it on the backplane.

E. Using a number 2 Phillips screwdriver with a shank of at least 64 mm (2.5 in.) length,

tighten the captive screws to 1.1 N ⋅m (10 lb ⋅in.) of torque.

NATIONAL

INSTRUMENTS

323334c.qxd 4/3/2003 4:19 PM Page 9

cFP-20xx Quick Start Guide ni.com

Install I/O Modules on the Backplane

A. Align the captive screws on the I/O module with the holes on the backplane.

B. Press firmly to seat the I/O module on the backplane.

C. Using a number 2 Phillips screwdriver with a shank of at least 64 mm (2.5 in.) length,

tighten the captive screws to 1.1 N ⋅m (10 lb ⋅in.) of torque.

D. Repeat this procedure to install additional I/O modules on the backplane.

323334c.qxd 4/3/2003 4:19 PM Page 10

Otros manuales para FieldPoint cFP-20 Series

Tabla de contenidos

Otros manuales de Controladores de National Instruments

National Instruments

National Instruments NI 3100 Manual de usuario

National Instruments

National Instruments CMS-9068 Instrucciones de montaje

National Instruments

National Instruments GPIB-ENET Series Manual de usuario

National Instruments

National Instruments PXIe-8881 Manual de usuario

National Instruments

National Instruments GPIB PCI-GPIB Manual de usuario

National Instruments

National Instruments PXI-8150B Manual de usuario

National Instruments

National Instruments PXI-7344 Manual de usuario

National Instruments

National Instruments NI PXI-8104 Manual de usuario

National Instruments

National Instruments PXIe-8106 Manual de usuario

National Instruments

National Instruments PXI-7340 Manual de usuario

National Instruments

National Instruments NI 7340 Manual de usuario

National Instruments

National Instruments cRIO-9038 Manual de usuario

National Instruments

National Instruments cRIO-9030 Manual de usuario

National Instruments

National Instruments myRIO-1950 Manual de usuario

National Instruments

National Instruments NI PXIe-8133 Manual de usuario

National Instruments

National Instruments 7344 Series Manual de usuario

National Instruments

National Instruments RMC-8354 Manual de usuario

National Instruments

National Instruments NI PXIe-8135 Manual de usuario

National Instruments

National Instruments CompactRIO cRIO-9035 Manual de usuario

National Instruments

National Instruments sbRIO-9860 Manual de usuario

National Instruments

National Instruments GPIB-232CT Manual de usuario

National Instruments

National Instruments IC-317 Series Manual de usuario

National Instruments

National Instruments CompactRIO cRIO-9025 Manual de usuario

National Instruments

National Instruments sbRIO-9605 Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario