National Instruments PXI-665 Series Manual de usuario

November 2003

323613A-01

NI PXI-665xInstallation Guide

This guide contains instructions for installing your NI PXI-665xcontroller and

NI-Sync software.

Installing the Software

Note Be sure to install the driver software before installing the

NI PXI-665xhardware.

Complete the following steps to install the software:

1. Place the NI-Sync CD in your CD-ROM drive.

2. Click Install NI-Sync in the window that appears. If no window appears,

run the setup.exe program on the CD.

3. Follow the prompts to install the NI-Sync driver.

• Select Typical to install the driver and support for the development

environments present on your computer.

• Select Custom to manually select which components should be installed.

4. Reboot the computer when prompted to do so, or shut down the computer and

install the hardware.

NI PXI-665x Installation Guide 2 ni.com

Installing the Hardware

The following are general installation instructions. Consult the chassis user

manual or technical reference manual for specific instructions and warnings about

installing new modules.

1. Power off and unplug the chassis.

2. Choose an available PXI slot in the PXI chassis.

Note You must install the NI PXI-665xin Slot 2 when replacing

PXI_CLK10 or when controlling PXI star triggers. When the device is

not installed in Slot 2, it can access only the PXI trigger bus.

3. Remove the filler panel for the PXI slot you chose in step 2.

4. Ground yourself using a grounding strap or by holding a grounded object.

Follow the ESD protection precautions described in the Unpacking section of

Chapter 1, Introduction, of the NI PXI-665x User Manual.

5. Remove any packing material from the front panel screws and backplane

connectors.

6. Insert the NI PXI-665xinto the PXI slot. Use the injector/ejector handle to

fully insert the module into the chassis.

7. Screw the front panel of the device to the front panel mounting rail of the

chassis.

8. Visually verify the installation. Make sure the module is not touching other

modules or components and is fully inserted into the slot.

9. Plug in and power on the chassis.

The NI PXI-665xis now installed.

© National Instruments Corporation 3 NI PXI-665x Installation Guide

Verifying the Installation

During the first boot following the software and hardware installation of the

NI PXI-665x, Windows detects the device, and the NI-Sync driver will initiate

communication with it. A green access LED on the front panel of the NI PXI-665x

confirms that the device has been found and the driver can communicate with it.

National Instruments™, NI™, and ni.com™ are trademarks of National Instruments Corporation. Product and company names mentioned

herein are trademarks or trade names of their respective companies. For patents covering National Instruments products, refer to the

appropriate location: Help»Patents in your software, the patents.txt file on your CD, or ni.com/patents.

©2003 National Instruments Corp. All rights reserved.

Tabla de contenidos

Otros manuales de Controladores de National Instruments

National Instruments

National Instruments VXIpc 600 Series Manual de usuario

National Instruments

National Instruments cRIO-9023 Manual de usuario

National Instruments

National Instruments Two-Slot Embedded Controller NI PXI-8183 Manual de usuario

National Instruments

National Instruments NI 7340 Manual de usuario

National Instruments

National Instruments GPIB-232 Manual de usuario

National Instruments

National Instruments Motion Control 7344 Manual de usuario

National Instruments

National Instruments NI-488.2M Manual de usuario

National Instruments

National Instruments GPIB-232CT-A IBCL EPROM Manual de usuario

National Instruments

National Instruments PXI-8232 Manual de usuario

National Instruments

National Instruments PCI-7330 Manual de usuario

National Instruments

National Instruments cRIO-9064 Manual de usuario

National Instruments

National Instruments cRIO-9033 Manual de usuario

National Instruments

National Instruments cDAQ-9133 Manual de usuario

National Instruments

National Instruments IC-3120 Manual de usuario

National Instruments

National Instruments PXIe-8100 Manual de usuario

National Instruments

National Instruments PXI-8150 Series Manual de usuario

National Instruments

National Instruments GPIB-110 Manual de usuario

National Instruments

National Instruments sbRIO-9637 Manual de usuario

National Instruments

National Instruments PXI-8119 Manual de usuario

National Instruments

National Instruments NI PXI-8104 Manual de usuario

National Instruments

National Instruments PXI 8351 Manual de usuario

National Instruments

National Instruments PCI-8212 Manual de usuario

National Instruments

National Instruments 3100 Manual de usuario

National Instruments

National Instruments IC-3173 Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario