National Instruments SCC-AI Series Manual de usuario

USER GUIDE

SCC-AI Series Isolated Analog

Input Modules

The SCC-AI Series isolated analog input modules (SCC-AIXX) can extract

a relatively low-amplitude input signal from a high-common-mode voltage

so the E Series DAQ device can measure the input signal. They also can

amplify and filter the input signal, resulting in higher measurement

resolution and accuracy.

SCC-AIXX modules are available in a range of gains from 0.2 to 200. They

contain lowpass filters of either 10 kHz or 4 Hz bandwidth. Table 1-1 gives

the gain and bandwidth for each module.

Table 1-1. SCC-AIXX Module Input/Output Range, Gain, and Bandwidth

Model Input Range Output Range Gain Bandwidth

SCC-AI01 ±42 V ±8.4 V 0.2 10 kHz

SCC-AI02 ±20 V ±10 V 0.5 10 kHz

SCC-AI03 ±10 V ±10 V 110 kHz

SCC-AI04 ±5 V ±10 V 210 kHz

SCC-AI05 ±1 V ±10 V 10 10 kHz

SCC-AI06 ±100 mV ±10 V 100 10 kHz

SCC-AI07 ±50 mV ±10 V 200 10 kHz

SCC-AI13 ±10 V ±10 V 14 Hz

SCC-AI14 ±5 V ±10 V 24 Hz

SCC-AI Series Isolated Analog Input Modules 2 ni.com

Conventions

The following conventions are used in this guide:

<> Angle brackets that contain numbers separated by an ellipsis represent

a range of values associated with a bit or signal name—for example,

AI <0..7>.

»The »symbol leads you through nested menu items and dialog box options

to a final action. The sequence File»Page Setup»Options directs you to

pull down the File menu, select the Page Setup item, and select Options

from the last dialog box.

This icon denotes a note, which alerts you to important information.

This icon denotes a caution, which advises you of precautions to take to

avoid injury, data loss, or a system crash. When this symbol is marked on

the product, refer to the Read Me First: Safety and Radio-Frequency

Interference document, shipped with the product, for precautions to take.

When symbol is marked on a product, it denotes a warning advising you to

take precautions to avoid electrical shock.

When symbol is marked on a product, it denotes a component that may be

hot. Touching this component may result in bodily injury.

bold Bold text denotes items that you must select in the software, such as menu

items and dialog box options. Bold text also denotes parameter names.

italic Italic text denotes variables, emphasis, a cross reference, or an introduction

to a key concept. This font also denotes text that is a placeholder for a word

or value that you must supply.

monospace Text in this font denotes text or characters that you should enter from the

keyboard, sections of code, programming examples, and syntax examples.

This font is also used for the proper names of disk drives, paths, directories,

programs, subprograms, subroutines, device names, functions, operations,

variables, filenames, and extensions.

SC-2345 SC-2345 refers to both the SC-2345 connector block and the SC-2345

configurable connector.

SCC SCC refers to any SCC series signal conditioning module.

©National Instruments Corporation 3 SCC-AI Series Isolated Analog Input Modules

What You Need to Get Started

To set up and use the SCC-AIXX, you need the following items:

❑SC-2345/2350 with one of the following:

– SCC-PWR01

– SCC-PWR02 and the PS01 power supply

– SCC-PWR03 (requires a 7 to 42 VDC power supply, not included)

❑One or more SCC-SGXX

❑SCC-SG Series Strain-Gauge Modules User Guide

❑SC-2345/2350 User Manual, available at ni.com

❑SCC Quick Start Guide, available at ni.com

❑Read Me First: Safety and Radio-Frequency Interference

❑SC-2345 Quick Reference Label

❑68-pin Basic or E Series DAQ device, documentation,

and 68-pin cable

❑1/8 in. flathead screwdriver

❑Numbers 1 and 2 Phillips screwdrivers

❑Wire insulation strippers

❑NI-DAQ (current version) for Windows 2000/NT/XP/Me

Note Software scaling of measurements is not supported on the Macintosh operating

system. Refer to the SCC-AIXX Module Pin Assignments section.

SCC-AI Series Isolated Analog Input Modules 4 ni.com

Device Specific Information

Note For general SCC module installation and signal connection information, and

information about the SC-2350 carrier, refer to the SCC Quick Start Guide, available

for download at ni.com/manuals.

Installing the Module

Caution Refer to the Read Me First: Safety and Radio-Frequency Interference document

before removing equipment covers or connecting/disconnecting any signal wires.

You can plug the SCC-AIXX into any analog input socket on the SC-2345.

The socket you choose determines which E Series DAQ device channels

receive the SCC-AIXX signals.

For single-stage input conditioning, plug the SCC-AIXX into any socket

J(X+1), where Xis 0 to 7, and connect the input signals to the module as

described in the Connecting the Input Signals section.

If you use the SCC-AIXX in a dual-stage configuration, the SCC-AIXX

must be the first-stage module. Plug it into any socket J(X+9) and plug the

second-stage SCC into socket J(X+1), where Xis 0 to 7. Connect the input

signals to the SCC-AIXX as described inthe Connecting the Input Signals

section. The SC-2345 connects the output signals of the first-stage SCC to

the inputs of the second-stage SCC. An example of dual-stage conditioning

is an SCC-AI02 followed by an SCC-FV01 frequency input module.

Sockets J9 to J16 are also available for digital input/output (DIO)

conditioning or control. Refer to the SC-2345 User Manual for more

information on configuring, connecting, and installing SCC modules.

Connecting the Input Signals

Note The signal names have changed. Refer to ni.com/info and enter rdtntg to

confirm the signal names.

Each screw terminal on the SCC-AIXX is labeled by pin number <1..4>.

Pins 1 and 2 form a channel routed to E Series DAQ device channel X+8,

and pins 3 and 4 form a channel routed to the E Series DAQ device channel

X, where Xis 0 to 7 depending on the socket where you plug in the module.

The SCC-AIXX provides channel-to-ground and module-to-module

isolation only. It does not provide isolation between the two channels of the

SCC-AIXX. Because both channels must have the same reference voltage,

pins 1 and 3 are connected together internally.

©National Instruments Corporation 5 SCC-AI Series Isolated Analog Input Modules

Figure 1-1 shows the SCC-AIXX signal connections.

Figure 1-1. SCC-AIXX Signal Connections

The inputs are designed in a floating (nonreferenced) single-ended

configuration. If the measured signals are floating, connect the negative

input pins, 1 and 3, to AI SENSE on the SC-2345 terminal block through

a10kΩto 100 kΩresistor. Figure 1-2 shows a floating signal connection

on one channel of the SCC-AIXX.

Figure 1-2. Nonreferenced Signal Connection for the SCC-AIXX (One Channel)

Lowpass

Filter

–

Lowpass

Filter

E Series DAQ Device

Signal

Source

AI (

)

SCC-AI

AI SENSE

AI GND

AI (

+8)

Lowpass

Filter

–

Lowpass

Filter

E Series DAQ Device

Signal

Source AI (

)

SCC-AI

AI SENSE

AI GND

AI (

+8)

AI SENSE

on SC-2345

terminal block

10–100 kΩ

SCC-AI Series Isolated Analog Input Modules 6 ni.com

If a high common-mode voltage is present, connect the negative input pins,

1 and 3, to the signal reference. Figure 1-3 shows a ground-referenced

signal connection on one channel of the SCC-AIXX.

Figure 1-3. Ground-Referenced Signal Connection for the SCC-AIXX

with High Common-Mode Voltage (One Channel)

For information about how to configure the SCC-AI module using

NI-DAQmx, refer to the SCC Quick Start Guide.

Using the SCC-AIXX when Scaling Voltage Measurements

If you configured the SCC-AIXX using Measurement & Automation

Explorer (MAX) and you are using NI-DAQ, the voltage reading you get

from the E Series DAQ device accounts for the voltage scaling effect of the

SCC-AIXX. Otherwise, because the voltage measurement from the

E Series DAQ device is scaled by the gain given in Table 1-1, you must

divide the voltage reading returned by the E Series DAQ device by this gain

to get the correct input voltage.

Lowpass

Filter

–

Lowpass

Filter

E Series DAQ Device

Signal

Source AI (

)

SCC-AI

AI SENSE

AI GND

AI (

+8)

High

CMV

–

©National Instruments Corporation 7 SCC-AI Series Isolated Analog Input Modules

Calibrating Gain and Offset Errors

The SCC-AIXX is calibrated at the factory before shipment. If you want to

adjust the gain of the SCC-AIXX in your system using your E Series DAQ

device, you need a voltage source that is several times more accurate than

the SCC itself and capable of providing the DC voltage shown in Table 1-2.

Gain Adjustment

To adjust the gain of the SCC-AIXX, complete the following steps:

1. Select the desired SCC-AIXX channel on the E Series DAQ device.

2. Set the gain on the E Series DAQ device so that its input range is ±10 V.

3. Connect the voltage source to the screw terminals of the desired

channel on the SCC-AIXX.

4. Apply the voltage given in Table 1-2 that corresponds to the

SCC-AIXX module. For example, if you have an SCC-AI03,

you must apply 8 VDC.

5. Using your software, have the E Series DAQ device read the desired

channel on the SCC-AIXX and record the value.

6. Input 0 VDC to the SCC-AIXX.

7. Use the E Series DAQ device to read that channel and record the value.

8. Subtract the values read (first reading – second reading).

Table 1-2. SCC-AIXX Input Voltage Requirements

Module Input Range

SCC-AI01 40 V

SCC-AI02 16 V

SCC-AI03 8 V

SCC-AI04 4 V

SCC-AI05 800 mV

SCC-AI06 80 mV

SCC-AI07 40 mV

SCC-AI13 8 V

SCC-AI14 4 V

SCC-AI Series Isolated Analog Input Modules 8 ni.com

9. Adjust the trimpot labeled Gain located on the top of the SCC-AIXX.

If the value you obtained in step 8 is less than the input voltage, turn

the trimpot clockwise to increase the gain. If it is greater than the input

voltage, turn the trimpot counterclockwise to decrease the gain.

10. Repeat steps 4 through 9 until the difference you get in step 8 equals

the Input Voltage Required value shown in Table 1-2; in this example

the value is 8 V using an SCC-AI03.

For example, assume that you have an SCC-AI03 module. You first connect

8 VDC to the input of CH (X). The E Series DAQ device reads 8.05 V as

the SCC output. You then connect 0 VDC to the input of CH (X) and the

E Series DAQ device reads –0.01 V as the SCC output. You subtract these

readings, 8.05 – (–0.01) =8.06, getting a difference of 8.06 V. Because this

difference is not equal to 8 V, you must adjust the gain trimpot and repeat

the procedure until the difference in outputs equals 8 V.

Note In this example there can be an offset voltage such that the final readings are 8.01 V

and 0.01 V for a difference of 8 V. The gain trimpot adjusted in step 9 of the previous

procedure adjusts only for gain errors and does not compensate for this offset voltage.

Offset Voltage Adjustment

Complete the following steps to adjust the offset voltage of the SCC-AIXX:

1. Select the desired SCC-AIXX channel on the E Series DAQ device.

2. Set the gain on the E Series DAQ device so that the input range

is ±10 V.

3. Connect the screw terminals of your desired channel on the SCC-AIXX

together.

4. Using your software, have the E Series DAQ device read the channel.

5. If the value read is not equal to 0.00 V, adjust the appropriate trimpot

located on the top of the SCC-AIXX, labeled Offset. Turn the trimpot

clockwise to increase the offset.

6. Repeat steps 4 and 5 until the voltage read in step 4 equals 0.00 V.

©National Instruments Corporation 9 SCC-AI Series Isolated Analog Input Modules

Specifications

These ratings are typical at 25 °C unless otherwise stated.

Input Characteristics

Number of input channels ...................... 2 NRSE

Isolation.................................................. Bank isolation (isolation

per module)1

Input/output signal range, gain,

and bandwidth ........................................ Refer to Table 1-1

Input impedance

SCC-AI01, SCC-AI02 .................... 1 MΩ

All others......................................... 100 MΩ

Gain error ............................................... 4.5% max (trimmable to zero)

Gain stability .......................................... 150 PPM/°C

Offset error............................................. 40 mV max (RTI2)

Offset stability........................................ 225 µV/°C

Nonlinearity ........................................... 0.0128% typ

0.0260% max

Common-mode rejection ratio ............... 100 dB typical at 60 Hz

Output slew rate,

dependent on BW (filtering) .................. 0.8 V/µs max

Filter Characteristics

Number of poles..................................... 3

Rolloff .................................................... 60 dB/decade

Cutoff frequency (–3 dB)

AI0X................................................ 10 kHz

AI1X................................................ 4 Hz

1 The SCC-AIXX does not provide isolation between the two channels of the module. For more information,

refer to the Connecting the Input Signals section.

2 This specification is calculated relative to the input range of the module.

SCC-AI Series Isolated Analog Input Modules 10 ni.com

Power Requirement

Analog power .........................................410 mW max

+15 V ...............................................13.67 mA max

–15 V ...............................................13.67 mA max

Digital power (+5 V) ..............................650 mW max

130 mA max

Physical

Dimensions .............................................8.89 cm ×2.92 cm ×1.85 cm

(3.5 in. ×1.15 in. ×0.73 in.)

I/O connectors.........................................One 20-pin right-angle

male connector,

one 4-pin screw terminal,

removable

Screw terminal wire gauge .....................24 to 12 AWG

Maximum Working Voltage

Maximum working voltage refers to the signal voltage plus the

common-mode voltage.

Channel-to-earth .....................................300 V, Installation Category II

Module-to-module ..................................300 V, Installation Category II

Channel-to-channel.................................Not isolated1

Environmental

Operating temperature ............................0 to 50 °C

Storage temperature ................................–20 to 70 °C

Humidity.................................................10 to 90% RH, noncondensing

Maximum altitude...................................2,000 m

Pollution Degree (indoor use only) ........2

1 The SCC-AIXX does not provide isolation between the two channels of the module. For more information,

refer to the Connecting the Input Signals section.

Otros manuales para SCC-AI Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Unidad de control de National Instruments

National Instruments

National Instruments cFP-RLY-421 Manual de usuario

National Instruments

National Instruments 9871 Manual de usuario

National Instruments

National Instruments PXIe-5698 Manual de usuario

National Instruments

National Instruments 9246 Manual de usuario

National Instruments

National Instruments REM-11102 Manual de usuario

National Instruments

National Instruments NI 9472 Manual de usuario

National Instruments

National Instruments PXIe-4310 Manual

National Instruments

National Instruments PXI Terminal Block NI TB-2708 Manual de usuario

National Instruments

National Instruments NI 9265 Manual de usuario

National Instruments

National Instruments C Series Manual de usuario

National Instruments

National Instruments NI PXIe-4464 Manual de usuario

National Instruments

National Instruments sbRIO-9205 Manual de usuario

National Instruments

National Instruments NI 9871 Manual de usuario

National Instruments

National Instruments SCC-DO01 Manual de usuario

National Instruments

National Instruments SCC-FV01 Manual de usuario

National Instruments

National Instruments NI 9269 Manual de usuario

National Instruments

National Instruments SCXI-1521 Manual de usuario

National Instruments

National Instruments SCXI-1502 Manual de usuario

National Instruments

National Instruments NI 6013 Guía de inicio rápido

National Instruments

National Instruments NI PXI-6682H Manual de usuario

National Instruments

National Instruments NI 9209 Manual

National Instruments

National Instruments PXIe-4480 Manual de usuario

National Instruments

National Instruments NI PXI-2585 Manual de usuario

National Instruments

National Instruments PXIe-6594 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario