National Instruments NI-9208 Manual

CALIBRATION PROCEDURE

NI 9208

16-channel, ±20 mA, 24-Bit Analog Input Module

This document contains the verification and adjustment procedures for the National

Instruments 9208. For more information on calibration, visit ni.com/calibration.

Contents

Software.................................................................................................................................... 1

Documentation.......................................................................................................................... 2

Test Equipment......................................................................................................................... 3

Test Conditions......................................................................................................................... 3

Initial Setup............................................................................................................................... 3

Verification ............................................................................................................................... 4

Accuracy Verification....................................................................................................... 4

Adjustment................................................................................................................................ 5

Current Accuracy Adjustment .......................................................................................... 5

EEPROM Update ..................................................................................................................... 6

Reverification ........................................................................................................................... 6

Accuracy Under Calibration Conditions .................................................................................. 7

Worldwide Support and Services ............................................................................................. 7

Software

Calibrating the NI 9208 requires the installation of NI-DAQmx 9.1 or later on the calibration

system. You can download NI-DAQmx from ni.com/downloads. NI-DAQmx supports

LabVIEW, LabWindows™/CVI™, C/C++, C#, and Visual Basic .NET. When you install

NI-DAQmx you only need to install support for the application software that you intend to use.

ni.com/manuals

DeutschFrançais

2|ni.com |NI 9208 Calibration Procedure

Documentation

Consult the following documents for information about the NI 9208, NI-DAQmx, and your

application software. All documents are available on ni.com and help files install with the

software.

NI cDAQ-9174/9178 USB Chassis Quick Start

NI-DAQmx installation and hardware setup

NI 9208 Operating Instructions and Specifications

NI 9208 specific information, specifications, and calibration interval

NI-DAQmx Readme

Operating system and application software support in NI-DAQmx

LabVIEW Help

LabVIEW programming concepts and reference information about NI-DAQmx

VIs and functions

NI-DAQmx C Reference Help

Reference information for NI-DAQmx C functions and NI-DAQmx C properties

NI-DAQmx .NET Help Support for Visual Studio

Reference information for NI-DAQmx .NET methods and NI-DAQmx .NET

properties, key concepts, and a C enum to .NET enum mapping table

NI 9208 Calibration Procedure |© National Instruments |3

Test Equipment

Table 1 lists the equipment recommended for the performance verification and adjustment

procedures. If the recommended equipment is not available, select a substitute using the

requirements listed in Table 1.

Test Conditions

The following setup and environmental conditions are required to ensure the NI 9208 meets

published specifications.

• Keep connections to the device as short as possible. Long cables and wires act as antennas,

picking up extra noise that can affect measurements.

• Verify that all connections to the device are secure.

• Use shielded copper wire for all cable connections to the device. Use twisted-pairs wire to

eliminate noise and thermal offsets.

• Maintain an ambient temperature of 23 ± 5 °C. The device temperature will be greater than

the ambient temperature.

• Keep relative humidity below 80%.

• Allow a warm-up time of at least 10 minutes to ensure that the NI 9208 measurement

circuitry is at a stable operating temperature.

Initial Setup

Complete the following steps to set up the NI 9208.

1. Install the NI-DAQmx driver software.

2. Make sure the NI cDAQ-9178 power source is not connected.

3. Install the NI 9208 in slot 8 of the NI cDAQ-9178 chassis. Leave slots 1 through 7 of the

NI cDAQ-9178 chassis empty.

4. Connect the NI cDAQ-9178 chassis to your host computer.

5. Connect the power source to the NI cDAQ-9178 chassis.

6. Launch Measurement & Automation Explorer (MAX).

7. Right-click the device name and select Self-Test to ensure that the device is working

properly.

Table 1. Recommended Equipment

Equipment

Recommended

Model Minimum Requirements

Source Fluke 5700A Use a high-precision current source with an

accuracy ≤100 ppm.

cDAQ Chassis NI cDAQ-9178 —

Connection Accessory NI 9923 —

4|ni.com |NI 9208 Calibration Procedure

Verification

The following performance verification procedure describes the sequence of operation and

provides test points required to verify the NI 9208. The verification procedure assumes that

adequate traceable uncertainties are available for the calibration references.

Accuracy Verification

Complete the following procedure to determine the As-Found status of the NI 9208.

1. Set the calibrator to Standby mode (STBY).

2. Connect the NI 9208 to the calibrator as shown in Figure 1.

Figure 1. NI 9208 Pin Assignments

Note If the calibrator outputs are truly floating, connect the negative output to a

quiet earth ground as well as COM to give the entire system a ground reference.

3. Set the calibrator current to a Test Point value indicated in Table 4.

4. Set the calibrator to Operate mode (OPR).

5. Acquire and average samples.

a. Create an AI current task on the NI 9208 according to Table 2.

1 Connections when using a calibrator with a guard connection.

2 Connections when using a calibrator with no guard connection.

Table 2. NI 9208 Configuration for Current Accuracy Verification

Input Range

Scaled Units Terminal ConfigurationMin Max

-0.02 0.02 Amps RSE

NI 9208Calibrator

COM

AIx

Guard

NI 9208Calibrator

COM

AIx

NI 9208 Calibration Procedure |© National Instruments |5

b. Configure the AI current task timing according to Table 3. Set the ADC timing mode

to high-resolution.

c. Start the task.

d. Average the readings.

e. Clear the task.

6. Compare the average to the limits in Table 4.

7. Set the calibrator to Standby mode (STBY).

8. Repeat steps 5 through 7 with the ADC timing mode on the NI 9208 set to high-speed.

9. Repeat steps 3 through 8 for each test point in Table 4.

10. Disconnect the calibrator from the device.

11. Repeat steps 2 through 10 for each channel on the NI 9208.

Adjustment

The following performance adjustment procedure describes the sequence of operation required

to adjust the NI 9208.

Current Accuracy Adjustment

Complete the following steps to adjust the current accuracy of the NI 9208.

1. Set the calibrator to Standby mode (STBY).

2. Connect the NI 9208 to the calibrator as shown in Figure 1.

3. Adjust the NI 9208 current accuracy.

a. Initialize a calibration session on the NI 9208. The default password is NI.

b. Input the external temperature in degrees Celsius.

Table 3. NI 9208 Current Timing Configuration

ADC Timing Mode Sample Mode Samples to Read

High-Resolution N Samples 5

High-Speed N Samples 75

Table 4. NI 9208 Test Limits for Current Accuracy Verification

Range (A) Test Point 1-Year Limits

Minimum Maximum Location Value (A) Lower Limit (A) Upper Limit (A)

-0.022000 0.022000 Positive FS 0.021000 0.020968 0.021032

-0.022000 0.022000 Mid 0.000000 -0.000004 0.000004

-0.022000 0.022000 Negative FS -0.021000 -0.021032 -0.020968

6|ni.com |NI 9208 Calibration Procedure

c. Call the NI 9208 get C Series adjustment points function to obtain an array of

recommended calibration currents for the NI 9208.

d. Set the calibrator to a reference value determined by the array of recommended

calibration currents.

e. Set the calibrator to Operate mode (OPR).

f. Call and configure the NI 9208 gain instance of the adjustment function according to

Table 5.

g. Set the calibrator to Standby mode (STBY).

h. Repeat steps d through g for each calibration current in the array.

i. Disconnect the calibrator from the NI 9208.

j. Call and configure the NI 9208 offset instance of the adjustment function for the

current channel.

k. Close the calibration session.

4. Repeat steps 1 through 3 for each channel on the NI 9208.

EEPROM Update

When an adjustment procedure is completed, the NI 9208 internal calibration memory

(EEPROM) is immediately updated.

If you do not want to perform an adjustment, you can update the calibration date and onboard

calibration temperature without making any adjustments by initializing an external calibration,

setting the C Series calibration temperature, and closing the external calibration.

Reverification

Repeat the Verification section to determine the As-Left status of the device.

Note If any test fails Reverification after performing an adjustment, verify that you

have met the Test Conditions before returning your device to NI. Refer to Worldwide

Support and Services for assistance in returning the device to NI.

Table 5. Gain Adjustment Configuration

Physical Channel Reference Value

cDAQMod8/aixThe reference value from the array of adjustment points

375971C-01 Dec14

Refer to the NI Trademarks and Logo Guidelines at ni.com/trademarks for more information on National Instruments trademarks. Other

product and company names mentioned herein are trademarks or trade names of their respective companies. For patents covering National

Instruments products/technology, refer to the appropriate location: Help»Patents in your software, the patents.txt file on your media, or the

National Instruments Patents Notice at ni.com/patents. You can find information about end-user license agreements (EULAs) and third-party

legal notices in the readme file for your NI product. Refer to the Export Compliance Information at ni.com/legal/export-compliance

for the National Instruments global trade compliance policy and how to obtain relevant HTS codes, ECCNs, and other import/export data. NI MAKES

NO EXPRESS OR IMPLIED WARRANTIES AS TO THE ACCURACY OF THE INFORMATION CONTAINED HEREIN AND SHALL NOT BE LIABLE FOR

ANY ERRORS. U.S. Government Customers: The data contained in this manual was developed at private expense and is subject to the applicable

limited rights and restricted data rights as set forth in FAR 52.227-14, DFAR 252.227-7014, and DFAR 252.227-7015.

Accuracy Under Calibration Conditions

The following accuracy table is valid for calibration under the following conditions:

• Ambient temperature of 23 ± 5 °C

• NI 9208 installed in slot 8 of an NI cDAQ-9178 chassis

• Slots 1 through 7 of the NI cDAQ-9178 chassis are empty

Note The test limits listed in Table 4 are derived using the values in Table 6.

Note For operational specifications, refer to the most recent NI 9208 Operating

Instructions and Specifications online at ni.com/manuals.

Worldwide Support and Services

The National Instruments website is your complete resource for technical support. At ni.com/

support you have access to everything from troubleshooting and application development

self-help resources to email and phone assistance from NI Application Engineers.

Visit ni.com/services for NI Factory Installation Services, repairs, extended warranty, and

other services.

Visit ni.com/register to register your National Instruments product. Product registration

facilitates technical support and ensures that you receive important information updates from NI.

National Instruments corporate headquarters is located at 11500 North Mopac Expressway,

Austin, Texas, 78759-3504. National Instruments also has offices located around the world. For

telephone support in the United States, create your service request at ni.com/support or dial

1 866 ASK MYNI (275 6964). For telephone support outside the United States, visit the

Worldwide Offices section of ni.com/niglobal to access the branch office websites, which

provide up-to-date contact information, support phone numbers, email addresses, and current

events.

Table 6. NI 9208 Accuracy Under Calibration Conditions

Percentage of Reading Percentage of Range*

0.132% 0.010%

* Range equals 22 mA.

Otros manuales para NI-9208

Tabla de contenidos

Otros manuales de Unidad de control de National Instruments

National Instruments

National Instruments 2591 Manual de usuario

National Instruments

National Instruments SCXI-1581 Manual de usuario

National Instruments

National Instruments NI 9203 Manual

National Instruments

National Instruments NI 9226 Manual de usuario

National Instruments

National Instruments NI 9425 Manual de usuario

National Instruments

National Instruments NI 9214 Manual de usuario

National Instruments

National Instruments FIeldPoint FP-AO-200 Manual de usuario

National Instruments

National Instruments SCC-AI Series Manual de usuario

National Instruments

National Instruments NI 9247 Manual de usuario

National Instruments

National Instruments 9235 Manual

National Instruments

National Instruments NI 9478 Manual de usuario

National Instruments

National Instruments NI 9227E Manual de usuario

National Instruments

National Instruments BNC-208X Series Manual de usuario

National Instruments

National Instruments PCIe-7858 Manual de usuario

National Instruments

National Instruments NI PXIe-7975R Manual de usuario

National Instruments

National Instruments SCXI-1581 Manual de usuario

National Instruments

National Instruments PXI-6683 Series Manual de usuario

National Instruments

National Instruments FP-AI-102 Manual de usuario

National Instruments

National Instruments SLSC-12251 Manual de usuario

National Instruments

National Instruments DAQCard-DIO-24 Manual de usuario

National Instruments

National Instruments 9759 Manual de usuario

National Instruments

National Instruments PXI-8214 Manual de usuario

National Instruments

National Instruments NI PXIe-4464 Manual de usuario

National Instruments

National Instruments NI-9244 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario