National Instruments PXIe-5832 Manual de usuario

PXIe-5832

Getting Started

2023-03-29

Contents

PXIe-5832 Getting Started Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Verifying the System Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Unpacking the Kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Verifying the Kit Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Preparing the Environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Choosing and Installing the Soware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Soware Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Installing the Soware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Installing the PXIe-5832. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Interconnecting the PXIe-5832 Modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Connecting mmWave Radio Heads. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Configuring the PXIe-5832 in MAX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Self-Calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Performing a Self-Calibration Using NI-RFSA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Locating the Soware and Examples. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Soware Locations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Programming Examples Locations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Making a First Measurement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

What Should I Do if the PXIe-3623 Does Not Appear in MAX?. . . . . . . . . . . . . . . . 26

Why Is the ACCESS LED O When the Chassis Is On?. . . . . . . . . . . . . . . . . . . . . . . 26

What Should I Do if the PXIe-5832 Fails the Self-Test?. . . . . . . . . . . . . . . . . . . . . . 27

What Should I Do if the Instrument Does Not Initialize?. . . . . . . . . . . . . . . . . . . . 27

Hardware Connectors and Indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

PXIe-5820. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

PXIe-3623 Front Panel and LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

PXIe-5653. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

mmRH-5582 Front Panel, Back Panel, and LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Where to Go Next. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

NI Services. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

ni.com

PXIe-5832 Getting Started

PXIe-5832 Getting Started Guide

Note Before you begin, install and configure your chassis and controller.

This document explains how to install, configure, and test the PXIe-5832. The

PXIe-5832 is a half-duplex RF communications instrument with up to 1 GHz of

instantaneous bandwidth, designed for stimulus/response test applications. You

can program the PXIe-5832 instrument using RFmx or NI-RFSA and NI-RFSG driver

soware.

The PXIe-5832 IF only instrument configuration comprises the following modules:

■ PXIe-5820 Vector Signal Transceiver

■ PXIe-3623 Vector Signal Up/Down Converter

The PXIe-5832 IF and mmWave instrument configuration comprises the following

modules:

■ PXIe-5820 Vector Signal Transceiver

■ PXIe-3623 Vector Signal Up/Down Converter

■ PXIe-5653 RF Analog Signal Generator (LO source)

■One or two mmRH-5582 mmWave Radio Heads

There is no single instrument labeled "PXIe-5832."

Instruments>\_Legal Information directory for information about NI copyright,

patents, trademarks, warranties, product warnings, and export compliance.

Verifying the System Requirements

To use the PXIe-5832, your system must meet certain requirements. For more

information about minimum system requirements, recommended system, and

supported application development environments (ADEs), refer to the readme,

which is installed or available at ni.com/manuals.

Unpacking the Kit

PXIe-5832 Getting Started

Notice To prevent electrostatic discharge (ESD) from damaging the

device, ground yourself using a grounding strap or by holding a grounded

object, such as your computer chassis.

1. Touch the antistatic package to a metal part of the computer chassis.

2. Remove the device from the package and inspect the device for loose

components or any other sign of damage.

Notice Never touch the exposed pins of connectors.

Note Do not install a device if it appears damaged in any way.

3. Unpack any other items and documentation from the kit.

Store the device in the antistatic package when the device is not in use.

Verifying the Kit Contents

The kit contents for the PXIe-5832 varies by your instrument configuration.

Table 1. Kit Contents by Configuration

Configuration Included Items

Intermediate frequency (IF) only instrument ■Modules:

■PXIe-5820

■PXIe-3623

■Cables:

■SMA (m)-to-SMA (m) cable, 304.8 mm

■MMCX (m)-to-MMCX (m), 87 mm

■ MMPX (m)-to-MMPX (m) cable,

40 mm (x8)

■ MMPX (m)-to-SMA (m) cable, 152 mm

(x2)

ni.com

PXIe-5832 Getting Started

Configuration Included Items

IF and mmWave instrument, which includes one

mmWave radio head with one of the following

port configurations:

■Direct TRX Ports (0-1)

■Switched TRX Ports (0-7), Direct TRX

Port (8)

■Switched TRX Ports (0-15)

■Modules:

■PXIe-5820

■PXIe-3623

■PXIe-5653

■mmRH-5582

■Cables:

■SMA (m)-to-SMA (m) cable, 304.8 mm

■SMA (m)-to-SMA (m) cable, 1 m (x3)

■ MMCX (m)-to-MMCX (m) cable,

87 mm

■ MMPX (m)-to-MMPX (m) cable,

40 mm (x8)

■ MMPX (m)-to-SMA (m) cable, 152 mm

(x2)

■Mini HDMI-to-Mini HDMI cable

■AC power supply adapter for

mmRH-5582

IF and mmWave instrument, which includes two

mmWave radio heads, each with one of the

following port configurations:

■Direct TRX Ports (0-1)

■Switched TRX Ports (0-7), Direct TRX

Port (8)

■Switched TRX Ports (0-15)

■Modules:

■PXIe-5820

■PXIe-3623

■PXIe-5653

■mmRH-5582 (x2)

■Cables:

■SMA (m)-to-SMA (m) cable, 304.8 mm

■SMA (m)-to-SMA (m) cable, 1 m (x6)

■ MMCX (m)-to-MMCX (m) cable,

87 mm

■ MMPX (m)-to-MMPX (m) cable,

40 mm (x8)

PXIe-5832 Getting Started

Configuration Included Items

■ MMPX (m)-to-SMA (m) cable, 152 mm

(x2)

■1.85 mm (m)-to-1.85 mm (m) cable,

200 mm

■Mini HDMI-to-Mini HDMI cable (x2)

■AC power supply adapter for

mmRH-5582 (x2)

Other Equipment

There are required items not included in your kit that you need to install or operate

the PXIe-5832. Your application may require additional items not included in your

kit to install or operate your hardware.

Required Items

■A PXI Express chassis and chassis documentation. To ensure specifications

are valid, NI recommends using the PXIe-1095 Chassis or PXIe-1092 Chassis for

your hardware. For more information about compatible chassis options, refer

to ni.com.

■A PXI Express embedded controller or MXI controller system that meets the

system requirements specified in this guide and chassis documentation.

Optional Items

■A 0.9 N · m (8 lb · in.) calibrated torque wrench, 5/16 in. (NI part number

751120-01).

Preparing the Environment

Ensure that the environment you are using the PXIe-5832 in meets the following

specifications.

Operating ambient temperature 0 °C to 45 °C

Operating relative humidity 10% to 90%, noncondensing (IEC 60068-2-56)

Maximum altitude 2,000m (800 mbar) (at 25 °C ambient

temperature)

ni.com

PXIe-5832 Getting Started

Pollution Degree 2

Indoor use only.

Notice Clean the hardware with a so, nonmetallic brush or lint free

cloth. Make sure that the hardware is completely dry and free from

contaminants before returning it to service.

Note Refer to the PXIe-5832 Specifications at ni.com/manuals for

complete specifications.

Soware Options

NI provides three soware options for programming the PXIe-5832—RFmx, NI-RFSA

and NI-RFSG instrument driver soware.

Table 2. PXIe-5832 Soware Options

Soware Option Description Use Case

RFmx Provides a single-handle

instrument driver with built-in

measurements.

You can use instrument driver

FPGA extensions to customize

the device FPGA using

precompiled bitfiles.

Use RFmx SpecAn to perform

spectral measurements.

Use RFmx Demod to perform

modulation quality

measurements, such as EVM.

Use RFmx personalities to

perform physical layer analysis

on supported communications

and connectivity signals.

NI-RFSA and NI-RFSG

instrument driver

The NI-RFSA and NI-RFSG APIs

each provide a fixed API for

interacting with your hardware.

NI-RFSA and NI-RFSG provide

standard IVI-based

functionality needed for most

vector signal analyzer and

vector signal generator

applications.

You can use NI-RFSA and

NI-RFSG instrument driver

FPGA extensions to customize

Use NI-RFSA to create custom

measurements or applications

that require I/Q data.

Use NI-RFSG to generate

continuous wave (CW) or

modulated waveforms.

Use NI-RFSA and NI-RFSG with

the NI Modulation Toolkit to

develop soware-defined radio

transmitters and receivers.

Use NI-RFSG with the

NI Modulation Toolkit to create

PXIe-5832 Getting Started

Soware Option Description Use Case

the device FPGA using

precompiled bitfiles.

and generate modulated

signals to test receivers.

Related information:

■Refer to the RFmx SpecAn Help, the RFmx Demod Help, the NI RF

Vector Signal Analyzers Help, or the NI RF Signal Generators Help for more

information about using the RFmx, NI-RFSA, and NI-RFSG instrument driver

FPGA extensions.

Installing the Soware

You must be an Administrator to install NI soware on your computer.

1. Install an ADE, such as LabVIEW or LabWindows™/CVI™.

2. Download the driver soware installer from ni.com/downloads.

NI Package Manager downloads with the driver soware to handle the

installation. Refer to the NI Package Manager Manual for more information

about installing, removing, and upgrading NI soware using NI Package

Manager.

3. Follow the instructions in the installation prompts.

Note Windows users may see access and security messages during

installation. Accept the prompts to complete the installation.

4. When the installer completes, select Restart in the dialog box that prompts

you to restart, shut down, or restart later.

Installing the PXIe-5832

Notice To prevent damage to the PXIe-5832 caused by ESD or

contamination, handle the module using the edges or the metal bracket.

1. Ensure the AC power source is connected to the chassis before installing the

module.

ni.com

PXIe-5832 Getting Started

The AC power cord grounds the chassis and protects it from electrical damage

while you install the module.

2. Power o the chassis.

3. Inspect the slot pins on the chassis backplane for any bends or damage prior

to installation. Do not install a module if the backplane is damaged.

4. Remove the black plastic covers from all the captive screws on the module

front panel.

5. Identify a supported slot in the chassis. The following figure shows the

symbols that indicate the slot types.

Figure 1. Chassis Compatibility Symbols

12 3 45

1. PXI Express System Controller Slot

2. PXI Peripheral Slot

3. PXI Express Hybrid Peripheral Slot

4. PXI Express System Timing Slot

5. PXI Express Peripheral Slot

6. Touch any metal part of the chassis to discharge static electricity.

7. Ensure that the ejector handle is in the downward (unlatched) position.

8. Place the module edges into the module guides at the top and bottom of the

chassis. Slide the module into the slot until it is fully inserted.

PXIe-5832 Getting Started

Figure 1. Module Installation

1. Chassis

2. Hardware Module

3. Ejector Handle in Downward (Unlatched) Position

9. Latch the module in place by pulling up on the ejector handle.

10. Secure the module front panel to the chassis using the front-panel mounting

screws.

Note Tightening the top and bottom mounting screws increases

mechanical stability and also electrically connects the front panel to

the chassis, which can improve the signal quality and

electromagnetic performance.

11. Cover all empty slots using either filler panels (standard or EMC) or slot

blockers with filler panels, depending on your application.

Note For more information about installing slot blockers and filler

panels, go to ni.com/r/pxiblocker.

12. Power on the chassis.

Related tasks:

■Installing the Soware

Interconnecting the PXIe-5832 Modules

ni.com

PXIe-5832 Getting Started

Tabla de contenidos

Otros manuales de Hardware de computadora de National Instruments

National Instruments

National Instruments USB-7856 Manual de usuario

National Instruments

National Instruments PXI NI 8171 Series Manual de usuario

National Instruments

National Instruments NI-488.2M Manual de usuario

National Instruments

National Instruments cFP-20xx Manual de usuario

National Instruments

National Instruments PXI-8101 Manual de usuario

National Instruments

National Instruments PXIe-8240 Manual de usuario

National Instruments

National Instruments PXI/CompactPCI Embedded Computer NI PXI-8108 Manual de usuario

National Instruments

National Instruments GPIB-1014 Series Manual de usuario

National Instruments

National Instruments SET-2090 Manual de lista de piezas

National Instruments

National Instruments NI PXIe-8105 Manual de usuario

National Instruments

National Instruments PXI-6031E Manual de usuario

National Instruments

National Instruments NI-9146 Manual del propietario

National Instruments

National Instruments Network Adapter NI PXIe-1075 Manual de usuario

National Instruments

National Instruments 800 Series Manual de usuario

National Instruments

National Instruments NI-9238 Manual de usuario

National Instruments

National Instruments NI 5922 Manual

National Instruments

National Instruments PCI-6110E/6111E Manual de usuario

National Instruments

National Instruments NI 9401 Manual de usuario

National Instruments

National Instruments NI PXIe-8105 Manual de usuario

National Instruments

National Instruments NI PXIe-8130 Manual de usuario

National Instruments

National Instruments SC-207 Series Manual de usuario

National Instruments

National Instruments NI PXIe-8133 Manual de usuario

National Instruments

National Instruments NI 6711 Manual de usuario

National Instruments

National Instruments PXI-GPIB Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario

Advantech

Advantech ASMB-935 Series Manual de usuario