MuxLab 500086 Manual de usuario
© MuxLab Inc. 94-000795-A
8495 Dalton Rd, Montreal, Quebec, Canada. H4T 1V5
Tel: (514) 905-0588 Fax: (514) 905-0589
Toll Free (North America): (877) 689-5228
E-mail: videoease@muxlab.com URL: www.muxlab.com
Specifications
Environment
Digital Audio
Standard Supported
LPCM, Dolby Digital® 5.1, DTS, and Dolby® True HD
Input / Output signal
S/PDIF coax cable or TOSLINK optic cable, input selectable.
Sampling rate
Up to 96kHz/24bits
Maximum distance between
unit
500 ft. (150m)
Connectors
RCA, TOSLINK, POWER, RJ45 on each unit.
Power requirement
1W max, 5V DC
S/PDIF spec
Coax 75 ohm with RCA connector,
level: 500mVp-p into 75 ohm
TOSLINK spec
Plastic optic cable with EIAJ/JEITA RC-5720C connector,
Wavelength: red 660nm, level: -15dBm max.
Cabling Requirement
(not supplied)
Any 4-pair straight cable CAT5/5E/6 with RJ-45 connector.
Coax and second Optic Cable.
Included in this kit
1 x TX unit, 1 x RX unit, 1 x 5V Power supply,
1 x Optic Cable 3ft (1m) and 1 x Installation guide.
RJ45 Pin Configuration
Pair 4+5 (data), 1+2+7(+5V), 3+6+8(0V)
Compatible mounting
hardware
500902, 500900, 500910, 500915
Temperature
Operating: -40° to 85°C (-40° to 185°F)
Storage: -40° to 85°C (-40° to 185°F)
Humidity
Maximum 95% (non-condensing)
Enclosure
ABS UL94HB fire retardant plastic
Dimensions
2.25” x 2.25” x 1.0” (6 x 6 x 2.5 cm) each box.
Shipping Weight
1 lb. (450g)
Warranty
2 Years
Order Information
500086 Digital Audio Extender
DIGITAL AUDIO EXTENDER KIT
500086
Quick Installation Guide
Overview
The Digital Audio Extender allows one (1) source of digital audio signal: coax (S/PDIF)
or optic (TOSLINK) to be connected to a receiver: coax or optic to up to 500 ft. (150m)
in a point-to-point configuration. The Extender supports most standards to transmit two
channels of uncompressed lossless PCM audio or compressed 5.1/7.1 surround sound,
such as Dolby Digital Plus or DTS-HD High Resolution Audio (multichannel digital
audio Dolby Digital® 5.1, DTS, and Dolby® True HD).
Applications
Transmission of Digital Audio Signal
© MuxLab Inc. 2015
Installation
One source unit can be connected to one receiver unit using a CAT5/6 cable. To install
the unit, perform the following steps:
Caution: Do not attempt to open the housing. There are no user-serviceable parts
inside the unit. Opening the unit will void your warranty.
Do not connect the unit to a telecommunication outlet wired to unrelated
equipment. Making such a connection may damage the equipment and/or
the unit. Verify that the desired twisted pairs are not being used for other
LAN or telephone equipment.
1. Use a dedicated 4-pair Cat5e/6 cable between the source and the receiver unit.
2. Patch panels are compatible.
3. Verify the wiring is “straight-through”, has 4 twisted pairs and has the standard Ethernet
RJ45 connector.
4. Connect the 5V power supply to one side only. Any side can be used.
5. Connect the unit to the audio source, either by coax source or optic. On the source
side, select which type of input is used. Both sides can be connected but only one is
used to transmit audio. At the receiver side both outputs will contain the same
signal. Note that some AV system may require that you connect only one signal.
Troubleshooting
The following tables describe some of the symptoms, probable causes and possible solutions regarding
the unit:
Symptom
Probable Cause
Possible Solutions
No audio
No signal from source
Source off.
Power missing. Check led.
Check continuity on all pair.
Check if pairs are not swapped.
Check if the four pairs are present.
Malfunctioning unit.
Intermittent audio or
no audio
Cable too long
If you still can’t diagnose the problem, please call MuxLab Customer Technical Support at
877-689-5228 (toll-free in North America) or (+1) 514-905-0588 (International).
Tabla de contenidos
Otros manuales de Extensor de MuxLab
MuxLab
MuxLab 500451-TX Manual de usuario
MuxLab
MuxLab 500753 Manual de usuario
MuxLab
MuxLab 500112 Manual de usuario
MuxLab
MuxLab 500115 Manual de usuario
MuxLab
MuxLab 500449 Manual de usuario
MuxLab
MuxLab 500140 Manual de usuario
MuxLab
MuxLab 500730 Manual de usuario
MuxLab
MuxLab VGA Balun II Manual de usuario
MuxLab
MuxLab 500758 Manual de usuario
MuxLab
MuxLab 500457 Manual de usuario
MuxLab
MuxLab 500453 Manual de usuario
MuxLab
MuxLab 500112 Manual de usuario
MuxLab
MuxLab 500464 Manual de usuario
MuxLab
MuxLab 500460 Manual de usuario
MuxLab
MuxLab 500454-POE Manual de usuario
MuxLab
MuxLab 500456 Manual de usuario
MuxLab
MuxLab 500456 Manual de usuario
MuxLab
MuxLab 500754 Manual de usuario
MuxLab
MuxLab VideoEase MonoPro XLR Guía del usuario
MuxLab
MuxLab 500451 Manual de usuario
