Munters WF54 Manual de usuario
1
© Munters Corporation, March 2017 QM1224r3
*Patents Pending
Instruction Manual
WF54 Tilt Wall Fan with Munters Drive
54” Tilt Wall Exhaust Fan
Models: WF54DTxxCXP-Hx • WF54DTxxCXJ-Hx
WF54
54” Tilt Fan with
Munters Drive*
© Munters Corporation , March 2017
2
QM1224r3
WF54 Tilt Fan with Munters Drive
Manual for use and Maintenance
Thank You:
Thank you for purchasing a Munters WF54 tilt fan with Munters Drive. Munters equipment is designed to be the
highest performing, highest quality equipment you can buy. With the proper installation and maintenance it will
provide many years of service.
Please Note:
To achieve maximum performance and insure long life from your Munters product it is essential that it be installed
and maintained properly. Please read all instructions carefully before beginning installation.
Warranty:
For Warranty claims information see the “Warranty Claims and Return Policy” form QM1021 available from the
Conditions and Limitations:
• Products and Systems involved in a warranty claim under the “Warranty Claims and Return Policy” shall have
been properly installed, maintained and operated under competent supervision, according to the instructions
provided by Munters Corporation.
• Malfunction or failure resulting from misuse, abuse, negligence, alteration, accident or lack of proper installation
or maintenance shall not be considered a defect under the Warranty.
3
© Munters Corporation, March 2017 QM1224r3
Index
Chapters Page
1. Unpacking the Equipment 3
1.1 Parts List 3
1.2 Fan Dimensions 5
2. Installation Instructions 6
2.1 Fan Installation 6
2.2 Shutter Installation 8
3. Electrical Wiring
9
3.1 Recommended Wire Routing 9
3.2 Electrical Wiring 10
4. Operation and Maintenance 16
4.1 Operation 16
4.2 Maintenenace 16
5. Troubleshooting 17
6. Winterizing 18
6.1 Winterizing 18
6.2 Winter Weather Protection 18
7. Exploded View and Parts List 19
© Munters Corporation , March 2017
4
QM1224r3
1.1 Parts List
Unpacking the Equipment
[A]
[B]
[C]
[D]
[E]
[F]
[G]
Each Crate includes:
1 – 54" Belt Drive Fan
4 – Cone Sections ( 2 side, 2 top/bottom)
4 – Support Brackets, galvanized
1 – Cone Guard
1 – Shutter
1 – Hardware Package HP1116 for GCX
HP1116 for 54GCX
[A]…..16 - ¼” x 1½” Lag Screws, ZP
[B]…..26 - ¼” x ½” Flange Head Bolts, ZP
[C]…..4 - ¼” x ¾” Flange Head Bolts, ZP
[D]…..10 - ¼” x 1¾” Flange Head Bolts, ZP
[E]…..40 - ¼” Flange Nuts, ZP
[F]…..8 - ¼” x ¾” TEK Screws, ZP
[G].....10 - ¾” O.D. x 1”L. Spacers
1.
Discharge cone is designed to mount on fan outlet for increased airow and to support the
exhaust guard. A shutter or guard must be mounted on the fan inlet.
NOTE:
Before beginning installation, check the overall condition of the equipment. Remove packing materials, and examine all
components for signs of shipping damage. Any shipping damage is the customer’s responsibility and should be reported
immediately to your freight carrier. Fan is shipped complete with all accessories. Remove shutter, guard and cone sections
before proceeding with installation.
5
© Munters Corporation, March 2017 QM1224r3
Cat. No. Cone Type A B C
Below F.O.
D E F G
Cone Height
H
Cone Width
Wall Openings
(W.O.)
WF54 54GCX 651⁄4” 631⁄4” 125⁄8” 56” 58” 225⁄8” 66” 59” 561⁄2”W. x 621⁄2”H.
Dimensions:
Unpacking the EquipmentChapter 1
A
Wall Opening (W.O.)
C
Wall Opening (W.O.)
A
1.2 Fan Dimentions E
Wall Opening (W.O)
D
H - Cone Width
B
F
Shutter
C
G - Cone Height
Fan Specifications: 60Hz shown (50Hz available)
Power: 230VAC or 230/460 VAC
Phase: 1 or 3
© Munters Corporation , March 2017
6
QM1224r3
2.1 Fan Installation
Step 1
Construct framed opening to correct size according to the Wall Opening
listed in chart below. See Figure 1A, 1B,1C and 1D.
Installation Instructions 2.
Figure 1A
Ceiling
Framing
H
(see chart A)
12"
W
(see chart A)
See minimum spac-
ing notes in Chart A Z
NOTE:
Chart A
A
2 x 4 framing
56½"W. x 62½"H.
Catalog No.
WF54
B
Concrete framing
56½"W. x 64"H.
Figure 1B
2 x 4 Framing
Figure 1C
Concrete Framing
Figure 1D
Greater than 4” Wall Thickness
B - Concrete Wall Opening
A - 2 x 4 Wall Opening
2 x 4
Framing cut
at 12° to
match fan
housing
3½"
Fan with Discharge Cone:
a minimum clearance
of 12” on all sides is
recommended, but fans
may be installed with less
clearance if required. The
minimum center-to-center
distance is 60”.
7
© Munters Corporation, March 2017 QM1224r3
Step 2
Slide fan assembly into framed wall opening from outside
of the building. Insert top of fan into opening and hold fan
against top frame. Midpoint of top panel must be aligned
with frameing for bottom flange of fan to pass through
opening. See Figure 2. Secure top and bottom flanges to
wall using (6) Screws [A]. See Figure 3A.
Step 3
Left and right flanges must be bent outward over framing.
This can be done by hand or with a rubber mallet. Be
careful to bend along perforation and not to distort the
housing. See Figure 3B.
Step 4
Confirm that housing inside dimensions match those shown
in Figure 4A. Then secure left and right flanges to wall
using (10) Screws [A] (provided). See Figure 4B & 4C.
Step 5
Outlet of fan comes unguarded, install discharge cone
with guard on outlet of fan at this time. Refer to QM1049
for flat sided cone installation instructions.
Figure 2
Installation InstructionsChapter 2
Figure 3A
Figure 3B
601⁄2”
Figure 4A
¼" x 1½ " Lag
screws [A]
Step 6
Make electrical connections to fan motor per instructions provided with fan or as shown on motor.
See Wiring Section on page 9.
NOTE:
This is NOT the Wall
Opening size.
56”
© Munters Corporation , March 2017
8
QM1224r3
Figure 4B Figure 4C
¼" x 1½" Lag
screws [A]
Installation InstructionsChapter 2
Figure 5A Figure 5B
Bottom
Shutter Clip
Step 1
Insert shutter into fan by sliding the bottom flange of shutter into bottom shutter clips and pressing shutter
inward, See Figure 5A. Fasten shutter in place by rotating the side and top shutter clips over the shutter
flanges, See Figure 5B.
Top
Shutter
Clip
Side Shutter Clip
2.2 Shutter Installation
9
© Munters Corporation, March 2017 QM1224r3
3.1 Recommended Wire Routing
Electrical Wiring 3.
Option 1 -
Step 1
The Munters Drive fan comes with a coil of electrical
cables that is pre-wired to the motor. Find the end of
the cable and form a drip loop and then run the cable
through the side of the fan housing, through flexible
conduit and into building. See Figure 6A & 6B.
Step 2
Add flashing and/or caulk around completed housing
on exterior side of building wall.
Option 2 -
Step 1
The Munters Drive fan comes with a coil of electrical
cables that is pre-wired to the motor. Find the end of the cable and form a drip loop and then run the cable
through housing and frame into wall cavity and into the building. See Figure 7A & 7B.
Step 2
Add flashing and/or caulk around completed housing on exterior side of building wall.
Drip
Loop
Figure 6B
Figure 7A
Figure 7B
Drip
Loop
Drip
Loop
2”
© Munters Corporation , March 2017
10
QM1224r3
Electrical WiringChapter 3
Recommended Lightning Protection
FC2003, 230V, 1 Phase
240 VAC
Power Supply for Fan
L1
L2
G
T1
T2
G
240 VAC
Power Out to Fan
Single Phase
Figure 8A
Safety Cut-Off Switch
T1
T2
T3
G
Three Phase
Power Out to Fan Motor
Three Phase
Power Supply for Fan
L1
L2
L3
G
Safety Cut-Off Switch
Three Phase
Figure 8B
Recommended Lightning Protection
FC2006, 230V, 3 Phase
FC2009, 460V, 3 Phase
All wiring should be installed in accordance with National, State, and Local electrical codes.
Fans used to ventilate livestock buildings or other rooms where continuous air movement is
essential should be connected to individual electrical circuits, with a minimum of two circuits per
room.
Single Phase and Three Phase Munters Drives: Power supply for fans to have Circuit Breaker
or Fuse Protection. The installer must refer to NEC and local codes to ensure safety and
compliance. See Figure 8A & 8B.
If recommended lightning protection was purchased, wire it to the fan power supply as shown and secure the
lightning protection unit near the disconnect or the bus panel. See Figure 8B & 8C (page 8).
NOTE: A safety cut-off switch should be located adjacent to each fan.
KEY:
L1=Line 1
L2=Line 2
L3=Line 3
H=Hot
N=Neutral
G=Ground
WARNING
!
High Voltage, disconnect power
before servicing.
Tabla de contenidos
Otros manuales de Admirador de Munters
Munters
Munters EC52D Manual de instrucciones
Munters
Munters VX55 Manual de usuario
Munters
Munters BI28M Manual de usuario
Munters
Munters Aerotech VX Series Manual de usuario
Munters
Munters Breeze Fan Manual de instrucciones
Munters
Munters RF-VX36-H Series Manual de usuario
Munters
Munters WM36F Manual de usuario
Munters
Munters WS55 Manual de usuario
Munters
Munters EC52 Manual de instrucciones
Munters
Munters EDC Series Manual de instrucciones
Munters
Munters EM52 Manual de usuario
Munters
Munters ATLAS 74 Manual de usuario
Munters
Munters WM54K Manual de usuario
Munters
Munters Vortex VX26F1CR Manual de usuario
Munters
Munters Aerotech VX36DFCP-H Series Manual de usuario
Munters
Munters EC50 Manual de instrucciones
Munters
Munters EDHE Series Manual de instrucciones
Munters
Munters Aerotech VX36DF Series Manual de usuario
Munters
Munters WM36KCB-6PK Series Manual de usuario
Munters
Munters EDC GHp Series Manual de instrucciones
