Munters AX Series Manual de usuario

1© Munters Corporation, December 2019 QM1059r6

Instruction Manual

AX and GB Series 36" Tilt Fan

with Galvanized Cone

Models: AX36Tx • AX36xTx • GB36Tx • GB36xTx

AX and GB

Series

36” Tilt Fans with

Galvanized Cone

2QM1059r6

Thank You:

Thank you for purchasing a AX/GB Series Tilt Fan. Munters equipment is designed to be the highest performing,

highest quality equipment you can buy. With the proper installation and maintenance it will provide many years

of service.

Please Note:

To achieve maximum performance and insure long life from your Munters product it is essential that it be

installed and maintained properly. Please read all instructions carefully before beginning installation.

Warranty:

For Warranty claims information see the “Warranty Claims and Return Policy” form QM1021 available from the

Munters Corporation office at 1-800-227-2376 or by e-mail at [email protected].

Conditions and Limitations:

• Products and Systems involved in a warranty claim under the “Warranty Claims and Return Policy” shall have

been properly installed, maintained and operated under competent supervision, according to the instructions

provided by Munters Corporation.

• Malfunction or failure resulting from misuse, abuse, negligence, alteration, accident or lack of proper

installation or maintenance shall not be considered a defect under the Warranty.

AX and GB Series 36" Tilt Fan with Cone

Instructions for Use and Maintenance

3© Munters Corporation, December 2019 QM1059r6

Index

Chapters Page

1. Unpacking the Equipment 4

1.1 Parts List 4

1.2 Dimensions 5

2. Installation Instructions 6

3. Electrical Wiring 9

3.1 Electrical Wiring 9

3.2 Recommended Wire Routing 10

4. Operation 11

5. Maintenance 12-13

6. Winterizing 14

7. Troubleshooting 15

8. Exploded View and Parts List 16-17

4QM1059r6

Unpacking the Equipment 1.

Each Crate Includes:

1 - 36” Belt Drive or Direct Drive fan

4 - Cone Sections

4 - Cone Support Brackets

1 - Cone Guard

1 - Shutter

1 - Hardware Package (HP1098):

Before beginning installation, check the overall condition of the equipment. Remove packing Materials and

examine all components for signs of shipping damage. Any shipping damage is the customers responsibility and

should be reported immediately to your freight carrier.

1.1 Parts List

HP1098 – Hardware Package for 36" Tilt Fan

ID Qty. Cat. No. Description

[A] 12 KS2463 ¹⁄₄" x 1.5" Hex Lag Screw, ZP

[B] 16 KS1153 ¹⁄₄"-20 x ¹⁄₂" SRTD HX Flange Head Bolt, ZP

[C] 12 KS1151 ¹⁄₄"-20 x ³⁄₄" SRTD HX Flange Head Bolt, ZP

[D] 28 KN0730 ¹⁄₄"-20 SRTD HX Flange Nut, ZP

[E] 8 KS2260 ¹⁄₄"-20 x ³⁄₄" SRTD HX Washer TEK Screw, ZP

5© Munters Corporation, December 2019 QM1059r6

1.2 Fan Dimensions

Fan Specifications: 60Hz shown (50Hz available)

Power: 120/240 VAC or 208-240/480 VAC

Phase: 1 or 3

Cat. No.

Fan

Dia. A B C D - Dia. E F G Wall Openings

( I.D., Framed)

AX/GB36T 36” 45¹⁄₄”W. x 453⁄4”H. 6” 123⁄16” 43¹⁄₂” 44³⁄₄” 46³⁄₈” 19⁵⁄₁₆” 43”W. x 45”H.

AX/GB365T 36” 45¹⁄₄”W. x 453⁄4”H. 6” 123⁄16” 43¹⁄₂” 44³⁄₄” 46³⁄₈” 19⁵⁄₁₆” 43”W. x 45”H.

Dimensions:

D - Dia.

Wall Opening

Unpacking the EquipmentChapter 1

Wall Opening

Wall OpeningG

Guard

6QM1059r6

2.1 Installation

Installation Instructions 2.

Framing

Wall Opening

(See chart)

Figure 1

See Clearance Notes

to right Wall Opening

(See chart)

Ceiling

Recommended Clearance*

•Fan with outlet guard: maintain 8"

minimum clearance on all sides

•Fan with discharge cone: maintain 12"

minimum clearance on all sides

Step 1

Construct a framed opening to correct size according to

Wall Opening listed in chart on previous page and your

fan size. See Figure 1.

Step 2

Insert fan into framed opening from the inside. See Figure 2.

Figure 2

7© Munters Corporation, December 2019 QM1059r6

Installation InstructionsChapter 2

Step 3

Confirm that housing inside dimensions match those shown in Figure 3A. Then secure housing to framing

using (12) Lag Screws [A]. See Figure 3B.

Lag Screw [A]

42"

Figure 3B

Figure 3A

NOTE:

This is NOT the

Wall Opening Size

Step 4

Proceed to the installation instructions for the Discharge Cone, Form QM1023. Once Discharge Cone is

completed, proceed to Electrical Wiring Section before the Shutter Installation.

Step 5

Add flashing and/or caulk around completed housing on exterior side of building wall.

Step 6

Make electrical connections to fan motor per instructions provided with fan or as shown on motor.

8QM1059r6

Installation InstructionsChapter 2

Step 7

Insert shutter into fan by sliding the bottom flange of shutter into bottom shutter clips and pressing shutter

inward, See Figure 4A. Fasten shutter in place by rotating the side and top shutter clips over the shutter

flanges. See Figure 4B.

Bottom Shutter

Clips

Shutter

Figure 4A

Figure 4B

9© Munters Corporation, December 2019 QM1059r6

Electrical Wiring 3.

KEY:

L1 = Line 1

L2 = Line 2

L3 = Line 3

H = Hot

N = Neutral

G = Ground

Figure 5A

Single Phase - Motor Overload Protection with Disconnect

(SY2000 or Equivalent)

120 or 240 VAC Power

Supply for Fan

L1 (H)

L2 (N)

T1 (H)

T2 (N)

120 or 240 VAC

Power Out to Fan

L1 (H)

L2 (N)

T1 (H)

T2 (N)

Three Phase Power

Supply for Fan

Three Phase

Power Out

to Fan Motor

L3 T3

Figure 5B

Three Phase - Motor Overload Protection with Disconnect

Motor Starter Safety Cut-oﬀ Switch

Information in parenthesis refers to 120 VAC control.

Note::

All wiring should be installed in accordance with National, State, and Local electrical codes. Fans used to ventilate

livestock buildings or other rooms where continuous air movement is essential should be connected to individual

electrical circuits, with a minimum of two circuits per room. For electrical connection requirements, refer to diagram on

motor nameplate and to information enclosed with the environmental control to be used.

Single Phase Fans

:motor overload protection should be provided for each fan. A Circuit Breaker Switch or

slow blow motor type fuses must be used

See Figure 5A

.See QM1400 for proper size.

Three Phase Fans:

motor overload protection should be provided for each fan. A three pole motor starter or

slow blow motor fuses must be used.

See Figure 5B

If a frequency drive (inverter) is used, confirm that motors are rated for inverter duty at the voltage used. The

installation of line reactors is recommended to reduce voltage spikes and harmonic distortion. Supplemental

motor overload protection is also recommended.

NOTE: A safety cut-off switch should be located adjacent to each fan.

3.1 Electrical Wiring

10 QM1059r6

Electrical WiringChapter 3

Step 7

As the power cable exits the back of the motor, form a Drip Loop and then run power cable down along

strut and "zip tie" the cable to strut to prevent cable from getting tangled in pulley or belt. See Figure 6.

Then run cable out the drain hole to the circuit breaker or control panel.

3.2 Recommended Wire Routing

Zip Tie

Drip Loop

Figure 6

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Admirador de Munters

Munters

Munters EM52 Manual de usuario

Munters

Munters BI28M Manual de usuario

Munters

Munters RF-VX36-H Series Manual de usuario

Munters

Munters EDC GHp Series Manual de instrucciones

Munters

Munters EC52 Manual de instrucciones

Munters

Munters WM54 K CB-6PK Series Manual de usuario

Munters

Munters EDC GHp Series Manual de instrucciones

Munters

Munters MFS36 Manual de instrucciones

Munters

Munters EM52 Manual de instrucciones

Munters

Munters Saturn ONE Manual de usuario

Munters

Munters Vortex VX26F1CR Manual de usuario

Munters

Munters CX Series Manual de usuario

Munters

Munters WF54 Manual de usuario

Munters

Munters EC52 Manual de instrucciones

Munters

Munters AT14F Manual de usuario

Munters

Munters WM36 K CB Series Manual de usuario

Munters

Munters CX24 Manual de usuario

Munters

Munters EC52 Manual de usuario

Munters

Munters Breeze Fan Manual de instrucciones

Munters

Munters EM50 Manual de usuario

Munters

Munters WM54 Manual de instrucciones

Munters

Munters WF50 Series Manual de usuario

Munters

Munters EDHE Series Manual de instrucciones

Munters

Munters TU600 Manual de instrucciones

Manuales populares de Admirador de otras marcas

ELTA FANS

ELTA FANS H03VV-F Manual de usuario

Hunter

Hunter 20714 Manual de instrucciones

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manual de usuario

Hunter

Hunter Caraway Manual de instrucciones

Panasonic

Panasonic FV-15NLFS1 Manual de usuario

Kompernass

Kompernass KH 1150 Manual de usuario

VES

VES FALA100/12V/TR Manual de usuario

Vertiv

Vertiv Liebert DCD Manual de usuario

Westinghouse

Westinghouse GFP Series Manual de usuario

Venmar

Venmar KUBIX HRV PLUS Series Manual de usuario

Maico

Maico ECR 31 Manual de usuario

Sonnenkonig

Sonnenkonig Dinky Manual de usuario

S&P

S&P ECOWATT HXBR Manual de usuario

Wider

Wider IMP03369BH Manual de usuario

Panasonic

Panasonic F-60DHN Manual de usuario

Hinkley

Hinkley HIGHLAND Manual de usuario

Broan

Broan 766BN Manual de usuario

Premium

Premium PFS16022 Instrucciones de montaje