Multitech RJModem MT5656RJ Manual de instrucciones

RJModem

MT5656RJ

Developer's Guide

Multi-Tech Systems, Inc. RJModem Developer's Guide (S000363I) 2

RJModem™ Developer's Guide

MT5656RJ

PN S000363I, Version I

This publication may not be reproduced, in whole or in part, without prior expressed written permission from Multi-

Multi-Tech Systems, Inc. makes no representations or warranties with respect to the contents hereof and specifically

disclaim any implied warranties of merchantability or fitness for any particular purpose. Furthermore, Multi-Tech

Systems, Inc. reserves the right to revise this publication and to make changes from time to time in the content hereof

without obligation of Multi-Tech Systems, Inc. to notify any person or organization of such revisions or changes.

Revisions

Revision Level Date Description

A 09/24/04 Initial release.

B 10/05/04 Added one drawing (bottom view) to the Dimensions page.

C10/14/04 Changed the RJModem drawing on page 10. Changed 5 V Serial Electrical to

VDDMAX=5.5 V. In the same table, removed the Current Drive cell.

D 05/12/05 Added the EMI filtering diagram. Updated the PCB footprint. Added panel-mounting

kit and board-mounting diagrams.

E 06/30/05 Added one more panel-mounting diagram. Add information on Transmit Clock

(TXCLK) and Receive Clock (RXCLK). Added reference to the separate AT

Command document for RJModem. Added Waste Electrical and Electronic

Equipment (WEEE) Notice.

F 07/08/05 Changed the Waste Electrical & Electronic Equipment (WEEE) Statement to Rev. B.

G 07/12/05 Added more text to the Pin Descriptions drawings.

H 11/30/05 Changed panel-mounting diagrams. Changed board drawing.

I 12/22/06 Changed the pin drawing. Changed the order of the drawings on pages 6 to 9.

RXCLK is now labeled output. Reversed the columns of pin numbers on the

schematic on page 17. Updated the following specifications: Certifications, DAA

isolation, power requirements.

Trademarks

Trademarks and registered trademarks of Multi-Tech Systems, Inc. are RJModem and the Multi-Tech logo.

Microsoft and Windows are registered trademarks or trademarks of Microsoft Corporation in the United States and/or

other countries.

Patents

This device covered by one or more of the following patents: 6,031,867; 6,012,113; 6,009,082; 5,905,794; 5,864,560;

5,815,567; 5,815,503; 5,812,534; 5,809,068; 5,790,532; 5,764,628; 5,764,627; 5,754,589; 5,724,356; 5,673,268;

5,673,257; 5,644,594; 5,628,030; 5,619,508; 5,617,423; 5,600,649; 5,592,586; 5,577,041; 5,574,725; 5,559,793;

5,546,448; 5,546,395; 5,535,204; 5,500,859; 5,471,470; 5,463,616; 5,453,986; 5,452,289; 5,450,425; 5,355,365;

5,309,562; 5,301,274; 7,082,106; 7,082,141; 7,092,406. Other Patents Pending.

World Headquarters

Multi-Tech Systems, Inc.

2205 Woodale Drive

Mounds View, Minnesota 55112

Phone: 763-785-3500 or 800-328-9717

Fax: 763-785-9874

Technical Support

Country By Email By Phone

France: [email protected] +(33) 1-64 61 09 81

India: support@multitechindia.com +91 (124) 2340780

Europe, Asia, Africa: [email protected] +(44) 118 959 7774

U.S., Canada, all others: support@multitech.com (800) 972-2439 or (763) 717-5863

Internet Address: http://www.multitech.com

Table of Contents

Multi-Tech Systems, Inc. RJModem Developer's Guide (S000363I) 3

Table of Contents

Chapter 1 – RJModem Hardware................................................................................................................................4

Introduction .............................................................................................................................................................4

RJModem Features ................................................................................................................................................4

Product Ordering Information..................................................................................................................................4

Developer Kit ..........................................................................................................................................................4

AT Commands ........................................................................................................................................................4

Technical Specifications .........................................................................................................................................5

Dimensions .............................................................................................................................................................6

For Board Mounting.........................................................................................................................................6

Panel Mounting .......................................................................................................................................................7

Attaching the Mounting Bracket ..............................................................................................................................7

Dimensional Drawing of the Bracket .......................................................................................................................8

Cable Specifications ...............................................................................................................................................8

PCB Footprint .........................................................................................................................................................9

Pinout Dimensions ................................................................................................................................................10

Pin Descriptions ....................................................................................................................................................10

Transmit Clock (TXCLK) and Receive Clock (RXCLK)..................................................................................11

&Q – Sync/Async Mode.................................................................................................................................11

&W – Store Current Configuration .................................................................................................................11

Electrical Characteristics.......................................................................................................................................12

3.3 V Serial RJModem...................................................................................................................................12

5 V Serial RJModem......................................................................................................................................12

Handling Precautions.....................................................................................................................................12

RJModem Developer Board..................................................................................................................................13

5 V / 3.3 V Jumper – JP6...............................................................................................................................14

RJModem Schematics...................................................................................................................................15

Design Considerations..........................................................................................................................................19

PC Board Layout Guidelines..........................................................................................................................19

Electromagnetic Interference (EMI) Considerations ......................................................................................19

EMI Filtering...................................................................................................................................................20

Chapter 2 – Telecom Approvals and Regulatory Information................................................................................21

Telecom Approvals ...............................................................................................................................................21

Regulatory Compliance Statements......................................................................................................................22

EMC, Safety, and R&TTE Directive Compliance...........................................................................................22

International Modem Restrictions ..................................................................................................................22

Telecom Requirements for the United States................................................................................................22

Industry Canada ............................................................................................................................................22

New Zealand Telecom Warning Notice..........................................................................................................23

South African Statement................................................................................................................................23

Other..............................................................................................................................................................23

Chapter 3 – Multi-Tech Warranty and Repairs Policy.............................................................................................24

Multi-Tech Warranty Statement ............................................................................................................................24

Repair Procedures for U.S. and Canadian Customers ..................................................................................24

Repair Procedures for International Customers (Outside U.S.A. and Canada) .............................................25

Repair Procedures for International Distributors............................................................................................25

Chapter 4 – Waste Electrical and Electronic Equipment (WEEE) Statement........................................................26

Index............................................................................................................................................................................27

Chapter 1 – RJModem Hardware

Multi-Tech Systems, Inc. RJModem Developer's Guide (S000363I) 4

Chapter 1 – RJModem Hardware

Introduction

The Multi-Tech RJModem creates communication-ready devices by integrating modem functionality into the most

compact, integrated device. The first-of-its-kind RJ11 form factor includes the controller, data pump, and DAA

providing device manufacturers with the ability to integrate dial-up connectivity into any product design. With minimal

engineering effort, the RJModem instantly adds global communication capabilities, enhancing the end user

experience and increasing product value.

RJModem Features

•Complete data modem including the controller, data pump, DAA, and RJ-11 connector

•V.92/56K, V.34/33.6K, V.32vis/14.4K data rate options

•High speed models backward compatible with lower speeds

•Telecom approved in more than 50 countries (some pending)

•V.44 and V.42 bis data compression

•V.42 error correction

•Intelligent DAA technology detects line status

•AT command compatible

•U. S. Caller ID reporting

•Low power/sleep mode

•FastPOS (V.29) and V.22vis Fast Connect

•V.80 Synchronous Access

•3.3V or 5V power input options

•Board mount or remote panel mounting

•Two-year warranty

Product Ordering Information

Product Description Region Order this Product

MT5656RJ-92 V.92 Serial Data Only 5V Global

MT5656RJ-34 V.34 Serial Data Only 5V Global

MT5656RJ-32 V.32bis Serial Data Only 5V Global

MT5656RJ-L-92 V.92bis Serial Data Only 3.3V Global

MT5656RJ-L-34 V.34 Serial Data Only 3.3V Global

MT5656RJ-L-32 V.32bis Serial Data Only 3.3V Global

MTRJ-DK Developer Kit Global

MTRJ-RMK Panel Mounting Kit for RJModem Global

Ordering Codes Description

92 V.92/56K Data Rate

34 V.34/33.6K Data Rate

32 V.32bis/14.4K Data Rate

L 3.3V Power Input

Note: Lead-free builds of the RJModem are available. Contact your sales representative.

Developer Kit

A Developer Kit is available. This kit provides the ability to plug in the RJModem and use it for testing, programming,

and evaluation. The kit includes one developer board with RS-232 DB-25 connector, universal power supply, RS-232

cable, RJ-11 cable, MTRJ-RMK Panel Mounting Kit, and Developer Guide CD.

AT Commands

The AT Commands for the RJModem are published in a separate document (document number S000364x) available

on the Developer Guide CD and on the Multi-Tech Web site.

Chapter 1 – RJModem Hardware

Multi-Tech Systems, Inc. RJModem Developer's Guide (S000363I) 5

Technical Specifications

The RJModem meets the following specifications:

Category Description

Data Standards V.92/V.90/56K, V.34/33.6K, V.32bis/14.4K, V.22, V.23, V.21;

Bell 212A and Bell103

Data Format Serial, binary, asynchronous

Serial Speeds Serial port data rates adjustable to 300, 1200, 2400, 4800, 9600, 19,200,

38,400, 57,600, 115,200

Client-to-Server Data Rates Supports V.92 and V.90 data rates

Client-to-Client Data Rates 33,600; 31,200; 28,800; 26,400; 24,000; 21,600; 19,200; 16,800; 14,400;

12,000; 9600; 7200; 4800; 2400; 1200; 0-300 bps

Error Correction Data Mode: V.42 (LAPM or MNP 2–4)

Data Compression V.44, V.42bis and MNP Class 5

Modes of Operation Full duplex over dial-up lines; data mode, command mode, and online command

mode, V.54 test mode

Dimensions .709" w x 2.519" h x .752 d (1.8 cm x 6.4 cm x 1.92 cm)

Weight 64 oz. (0.02 Kg)

Operating Temperature 3.3 V and 5V Build Options

0 to +50° C ambient under closed conditions

Storage Temperature -40 to +85° C

Humidity Humidity range 20% to 90% (non-condensing)

Operating Voltage 5V DC Build Option ± 10% –Absolute Maximum Supply Voltage: 5.5VDC

3.3V DC Build Option ± 10% – Absolute Maximum Supply Voltage: 3.6VDC

Power Requirements 5V Build Option Typical: 93mA (.46W @ 5VDC)

Maximum: 112mA (.59W @ 5.25VDC)

3.3 V Build Option Typical: 100mA (.33W @ 3.3VDC)

Maximum:112mA (.40W @ 3.6VDC)

Transmit Level -11 dBm (varies by country setting)

Receiver Sensitivity -43 dBm under worst-case conditions

Frequency Stability ±0.01%

DAA Isolation 1.5Kv r.m.s. or 2121 VDC at working voltage of 250VAC

Flow Control XON/XOFF (software), RTS/CTS (hardware)

Command Buffer 60 characters

Telephony / TAM TAM (Telephone Answering Machine): S-101 AT+V commands (no CODEC for

speakers/microphone interface)

Certifications and

Approvals Safety Certifications EMC Approvals

UL 60950-1 FCC Part 15 (Class B)

IEC 60950-1 Canada (Class B)

AS/NZS 6950:2000 EN 55022 (Class B)

CCC EN 55024

Warranty Two years

Intelligent Features Complete data modem including the controller, data pump, DAA, and RJ-11

connector

High speed models backward compatible with lower speeds

Telecom approved in more than 50 countries (some pending)

Intelligent DAA technology detects line status

AT command compatible

U. S. Caller ID reporting

Low power/sleep mode

FastPOS (V.29) and V.22vis Fast Connect

V.80 Synchronous Access

Board mount or remote panel mounting

Chapter 1 – RJModem Hardware

Multi-Tech Systems, Inc. RJModem Developer's Guide (S000363I) 6

Dimensions

For Board Mounting

Top View

Bottom View

Chapter 1 – RJModem Hardware

Multi-Tech Systems, Inc. RJModem Developer's Guide (S000363I) 7

Panel Mounting

Note: Screws, bracket and ribbon cable are included in the panel-mounting kit.

Attaching the Mounting Bracket

Chapter 1 – RJModem Hardware

Multi-Tech Systems, Inc. RJModem Developer's Guide (S000363I) 8

Dimensional Drawing of the Bracket

Cable Specifications

Chapter 1 – RJModem Hardware

Multi-Tech Systems, Inc. RJModem Developer's Guide (S000363I) 9

PCB Footprint

Notes:

Surface mount connectors are approved in place of soldering the unit to

the motherboard.

Follow the "Pass Through" footprint instructions on the part data sheets.

The following are recommended by Multi-Tech:

www.samtec.com

SAMTEC: SMM-107-02-S-D-(other option) or equivalent

SAMTEC: CLT-107-02-(plating option)-D-(other option) or equivalent

Chapter 1 – RJModem Hardware

Multi-Tech Systems, Inc. RJModem Developer's Guide (S000363I) 10

Pinout Dimensions

PCB Footprint or Board Lay-out (Note: This is the PCB top view)

Pin Descriptions

Top View

PCB Top Surface

Front RJModem Jack Opening

Pin Signal

Name IN/OUT

Type Description

1 –RI O RING (Active Low). Incoming ring signal from phone.

Ring Indicate. –RI output ON (low) indicates the presence of an ON segment of a ring

signal on the telephone line. The modem will not go off-hook when –RI is active; the

modem waits for –RI to go inactive before going off-hook.

2 –DCD O Data Carrier Detect (Active Low). –DCD output is ON (low) when a data connection is

established and the module is ready to send/receive data.

3 –DTR I Data Terminal Ready (Active Low). The –DTR input is turned ON (low) when the DTE is

ready to communicate. –DTR ON prepares the modem to be connected, and, once

connected, maintains the connection. –DTR OFF places the modem in the disconnect

state under control of the &Dn and &Qn commands.

4–RESET I Device Reset (with pull-up). The active low –RESET input resets the device logic and

returns the configuration of the device to the original factory default values or "stored

values" in the NVRAM. –RESET is tied to VCC through a time-constant circuit for “Power-

on-Reset” functionality. The module is ready to accept commands after a fixed amount of

time after power-on or reset.

5 VCC PWR

DC Input Power. 3.3 V or 5 V DC power, depending upon the build.

6 –CTS O Clear to Send (Active Low). –CTS is controlled by the module to indicate whether or not

the module is ready to transmit data. –CTS ON indicates to the DTE that signals on TXD

will be transmitted. –CTS OFF indicates to the DTE that it should not transfer data on TXD.

7 –RTS I Request to Sent (Active Low). –RTS signal is used for hardware flow control. –RTS

input ON (low) indicates that the DTE is ready to send data to the modem. In the

command state, the modem ignores –RTS.

Otros manuales para RJModem MT5656RJ

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Módem de Multitech

Multitech

Multitech IWAY MT128ISA-UV Manual de usuario

Multitech

Multitech MultiConnect Adapter Manual de usuario

Multitech

Multitech MultiConnect Adapter Manual de usuario

Multitech

Multitech MultiModem MTCBA-C Manual de usuario

Multitech

Multitech MultiModem MT5656ZDX-Series Manual de usuario

Multitech

Multitech MultiConnect Cell MTC-LVW2 Manual de usuario

Multitech

Multitech MTSMC-E Manual de usuario

Multitech

Multitech MultiModem CMDA MTCBA-C1X Manual de usuario

Multitech

Multitech MTCBA-C Manual de usuario

Multitech

Multitech MultiModem MT5600ZDX Manual de usuario

Multitech

Multitech MTSMC-G2 Instrucciones de instalación

Multitech

Multitech Dragonfly MTQ-LEU7 Guía de aplicación

Multitech

Multitech QuickCarrier USB-D Manual de usuario

Multitech

Multitech MT2834BA Manual de usuario

Multitech

Multitech MultiModem MT5600ZDX Manual de usuario

Multitech

Multitech MultiConnect Cell MTC-G3 Manual de usuario

Multitech

Multitech MT5600BA Manual de usuario

Multitech

Multitech MTCBA-E-U Manual de usuario

Multitech

Multitech MultiMobile MT9234MU-CDC Manual de usuario

Multitech

Multitech MT5634ZLXI/E Manual técnico

Multitech

Multitech MULTI MODEM II MT5600BA Manual de usuario

Multitech

Multitech MultiModemII MT5600BR-V92 Manual de usuario

Multitech

Multitech SocketModem Series Guía de aplicación

Multitech

Multitech MultiModem ZBA MT9234ZBA Manual de usuario

Manuales populares de Módem de otras marcas

Davicom

Davicom DM562AP Manual de usuario

EpiValley

EpiValley TATA indicom SXC-1080 Manual de usuario

Zte

Zte WiMAX Manual de usuario

Intelimax

Intelimax MA-2060 Manual de usuario

SMC Networks

SMC Networks D3CM1604V Manual de uso y cuidado

Telstra

Telstra Wi-Fi 4G Advanced Pro X Manual de usuario

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Manual de usuario

Samsung

Samsung AceLink SAM-335A Manual de usuario

Enfora

Enfora Enabler-G Guía de configuración rápida

iRZ

iRZ ATM2-232 Manual de usuario

Zhone

Zhone 6310 Manual de usuario

Paradyne

Paradyne Hotwire 7976 Manual de usuario

US Robotics

US Robotics 3453C Manual de usuario

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manual de usuario

Zte

Zte MF823 Manual de usuario

Four-Faith

Four-Faith F1403 Manual de usuario

Sierra Wireless

Sierra Wireless AIRLINK MP595W Manual de usuario

Gemtek

Gemtek WiMAX WIXFBR-103 Manual de usuario