MTX WET65T Manual de usuario

MTX.COM

WET65T

TOWER SPEAKER

OWNER’S MANUAL

MTX.COM

2

PRODUCT INFORMATION

Model #

Serial #

Dealer’s Name

Date of Purchase

IN THE BOX

• Speaker and Enclosure

• Brackets

• For mounting the bracket base to the enclosure

• (8) M6-1.0x14mm stainless steel Hex Bolt

• (8) M6 at washer stainless steel

• (8) M6 split lock washer stainless steel

• For tightening the bracket strap to the base

• (2) M6-1.0x50mm stainless steel Hex Bolt

• (2) M6 serrated ange lock nut stainless steel

INTRODUCTION

Thank you for purchasing this MTX Audio tower speaker pod. This high performance speaker features

all-weather construction designed to deliver exceptional sound quality and volume for high output systems

for those that love to hear their music wherever they are. Congratulations and enjoy the ultimate audio

experience with MTX!

FEATURES

• Weather Resistant Enclosure

• Fits 21⁄4", 23⁄8", 21⁄2"and 3"Bars

• Polypropylene Woofer and 1" Soft Dome Tweeter

• ABS Impact Resistance Grille with UV Inhibitor

• Tested 500 hrs to ASTM B117, D4329 Standard

• Internal Crossover Network

SPECIFICATIONS

RMS Power Handling: 75-Watts

Peak Power Handling: 150-Watts

Sensitivity (2.83V / 1m): 91.6dB

Sensitivity (1W / 1m): 87.3dB

Frequency Response: 60Hz - 20kHz

Impedance: 4Ω

Fits Bars 21⁄4", 23⁄8", 21⁄2", 3"

WIRE COLOR

Grey / Black +/- speaker wire

MTX.COM 3

INSTALLATION

1. Choose appropriate bracket clamp, 21⁄4", 23⁄8", 21⁄2"and 3", for the application.

2. Attach bracket base to enclosure at desired angle using a minimum of two (2) M6-1.0x14mm Hex

bolts and M6 lock washers. If only two bolts are used, ensure there is a bolt on each side of the

round base for secure mounting.

3. Slide bracket clamp over pipe or bar at desired mounting location.

4. Hold the enclosure in place where the base ts in the open section of the clamp. Then place the

M6-1.0x50mm Hex bolt through making sure the threads are towards the front of the enclosure.

See Figure 1.

5. Tighten the M6 serrated nut on to the bolt until the bracket is tight. The nut is serrated and

will lock in place. The speaker will not rotate on the bar it is mounted on when these are fully

tightened.

6. Adjust and tighten the bolts to the desired position making sure to use a minimum of two bolts.

Depending on the position of the speaker only two (2) insertion points will be usable.

7. Attach the MTX badge to the rear recess of the enclosure with the included double stick tape.

8. Connect the speaker wires to your amplier ensuring correct polarity +/+ and -/-.

Figure 1

MTX.COM

4

© 2015 Mitek Corporation. All rights reserved. MTX is a trademark of Mitek Corporation. Designed and

Engineered in the U.S.A.

Due to continual product development, all specications are subject to change without notice.

MTX Audio, 4545 East Baseline Rd. Phoenix, AZ 85042 U.S.A. 1-800-225-5689

MTX005258 RevB 8/15 • 21A10434 • AW0015167

The bracket base can rotate in any direction desired, a minimum of 2 bolts must be used, 1 on each side.

Tabla de contenidos

Otros manuales de Oradores de MTX

Manuales populares de Oradores de otras marcas

argon audio

argon audio IE20 Manual de usuario

Denon

Denon SC-N7 Manual de usuario

Gemline

Gemline Ace 3952 Manual de usuario

Focal

Focal ON WALL 300 Manual de instrucciones

HEADRUSH

HEADRUSH Maximus HRSP 5024 Manual de usuario

SoundLogic

SoundLogic BCCS-6/6395 Manual de usuario

Peavey

Peavey DTH 218 Manual de usuario

Avantree

Avantree Pluto Air Manual de usuario

Morel

Morel Integra Series INTEGRA OVATION 4 Manual de usuario

Oppo

Oppo SONICA Manual de usuario

Bose

Bose SoundLink Wireless Music System Manual de usuario

Rocksteady

Rocksteady Stadium Manual de usuario

Bowers & Wilkins

Bowers & Wilkins 4 Manual de usuario

Sonance

Sonance SONOS OUTDOOR Series Manual de usuario

Electro-Voice

Electro-Voice EVID FM4.2 Manual de usuario

Pioneer

Pioneer XW-HTD630 Manual de usuario

Onn

Onn BWA16AA002 Manual de usuario

HP

HP GL313AA - USB Speakers PC Multimedia Manual de usuario