MTX THUNDER SPORTSMUD65P Manual de usuario
MTX.COM
MUD65P
CAGE MOUNT SPEAKER
OWNER’S MANUAL
MTX.COM
2
PRODUCT INFORMATION
Model #
Serial #
Dealer’s Name
Date of Purchase
IN THE BOX
• Speaker and Enclosure
• Brackets
• For mounting the bracket base to the enclosure
• (8) M6-1.0x14mm stainless steel Hex Bolt
• (8) M6 at washer stainless steel
• (8) M6 split lock washer stainless steel
• For tightening the bracket strap to the base
• (2) M6-1.0x50mm stainless steel Hex Bolt
• (2) M6 serrated ange lock nut stainless steel
INTRODUCTION
Thank you for purchasing this MTX Audio cage mount speaker pod. This high performance speaker
features all-weather construction designed to deliver exceptional sound quality and volume for high
output systems for those that love to hear their music wherever they are. Congratulations and enjoy the
ultimate audio experience with MTX!
FEATURES
• Weather Resistant Enclosure
• Fits 11⁄2", 13⁄4"and 2" Bars
• Polypropylene Woofer and Mylar Dome Tweeter
• ABS Impact Resistant Grille with UV Inhibitor
• Tested 500 hrs to ASTM B117, D4329 Standard
• Red LED Speaker Illumination
SPECIFICATIONS
RMS Power Handling: 50-Watts
Peak Power Handling: 100-Watts
Sensitivity (2.83V/1m): 89.9dB
Sensitivity (1W/1m): 85.6dB
Frequency Response: 70Hz - 20kHz
Impedance: 4Ω
Fits Bars 11⁄2", 13⁄4", 2"
WIRE COLOR
Grey / Black - +/- speaker wire
Yellow / Black - +/- speaker illumination
MTX.COM 3
INSTALLATION
1. Choose appropriate bracket clamp, 11⁄2", 13⁄4"or 2", for the application.
2. Attach bracket base to enclosure at desired angle using a minimum of two (2) M6-1.0x14mm Hex
bolts and M6 lock washers. If only two (2) bolts are used, ensure there is a bolt on each side of
the round base for secure mounting.
3. Slide bracket clamp over pipe or bar at desired mounting location.
4. Hold the enclosure in place where the base ts in the open section of the clamp. Then place the
M6-1.0x50mm Hex bolt through making sure the threads are towards the front of the enclosure.
See Figure 1.
5. Tighten the M6 serrated nut onto the bolt until the bracket is tight. The nut is serrated and will lock
in place. The speaker will not rotate on the bar it is mounted on when these are fully tightened.
6. Adjust and tighten the bolts to the desired position making sure to use a minimum of two bolts.
Depending on the position of the speaker, only two (2) insertion points will be usable.
7. Attach the MTX badge to the rear recess of the enclosure with the included double stick tape.
8. Connect the speaker wires to your amplier ensuring correct polarity Grey to positive and
Black to negative.
The MUD65P includes speaker illumination. Connect the Yellow wire to +12VDC and the Black
wire to a ground location (preferably the same ground location as the amplier to avoid noise).
Current draw is 14.5mA.
Figure 1
MTX.COM
4
© 2015 Mitek Corporation. All rights reserved. MTX is a trademark of Mitek Corporation. Designed and
Engineered in the U.S.A.
Due to continual product development, all specications are subject to change without notice.
MTX Audio, 4545 East Baseline Rd. Phoenix, AZ 85042 U.S.A. 1-800-225-5689
MTX005257 RevA 7/15 •21A10428 • AW0015151
The bracket base can rotate in any direction desired, a minimum of 2 bolts must be used, 1 on each side.
Tabla de contenidos
Otros manuales de Oradores de MTX
MTX
MTX MUSICA SERIES Manual de usuario
MTX
MTX Blueprint 510CM Manual de usuario
MTX
MTX MONITOR5i Manual de usuario
MTX
MTX T5512-44 Manual de usuario
MTX
MTX CT620C Manual
MTX
MTX PROXP-20-FS Manual de usuario
MTX
MTX MPP4200 Manual de usuario
MTX
MTX X3-17-FS-U Manual de usuario
MTX
MTX iP3 Manual de usuario
MTX
MTX Thunder TR5510-04 Manual de instrucciones
MTX
MTX 512C Manual de usuario
MTX
MTX Blueprint 602W Manual de usuario
MTX
MTX WET65T Manual de usuario
MTX
MTX AW52 Manual de usuario
MTX
MTX Blueprint 620WE Manual de usuario
MTX
MTX Blueprint 520C Manual de usuario
MTX
MTX H620C Manual
MTX
MTX SS7 Manual de usuario
MTX
MTX MP52B Manual de usuario
MTX
MTX 620CE Manual de usuario
