MSA LH 350 Manual de usuario

CONFIDENTIAL INDUSTRY

Ref : 180722 – PP0200175 ind00 1/18

MAINTENANCE MANUAL

LH 350 FLIGHT HELMET

CONFIDENTIAL INDUSTRY

Ref : 180722 – PP0200175 ind00 2/18

Table of Contents

Topic Page

Table of Contents 2/19

WARNING 3/19

DESCRIPTION OF HELMET 4/19

GUARANTEE 5/19

PREAMBLE 6/19

CHINSTRAP 7/19

CLOTHING 8/19

OUTER VISOR 9/19

INNER VISOR 10/19

NVG HARD COVER 11/19

THE INNER IMPACT CAP 12 and 13/19

NECK PAD 14/19

ACCESS TO ELECTRONIC CARD 15/19

ELECTRONIC CARD 16/19

INSPECTION VERIFICATION 17/19

AND MAINTENANCE REQUIREMENTS

MANDATORY INSPECTION 18/19

AND REPLACEMENT CRITERIA

CONFIDENTIAL INDUSTRY

Ref : 180722 – PP0200175 ind00 3/18

WARNING

Thank you for placing your trust in MSA products.

Please read these instructions carefully before using your helmet.

Failure to observe these instructions could reduce the amount of protection your

helmet provides.

Your helmet will only provide maximum protection if all of the MSA

components are used with

it. Furthermore, any change made to your helmet or failure to use one of the original

helmet components will imply improper use of the equipment, and will discharge MSA

of any liability.

In an ongoing effort to improve its products, MSA

hereby reserves the right to alter them at no

notice.

To guarantee sufficient protection, the helmet must be adapted and adjusted to the

wearer’s head size.

Your helmet is desig

ned such that the pressure built up when it is knocked is absorbed

by the partial destruction or damage to the outer and inner cap; even if such damage is

not immediately apparent, we recommend replacing any helmet which has taken a

considerable impact.

The user’s attention is also drawn to the dangers of modifying or removing any of the

original components of the helmet, apart from any modification or removal

recommended by the helmet manufacturer. Under no circumstances should helmets be

adapted for attachment of accessories by any means not recommended by the helmet

manufacturer.

Do not apply any paint, solvents, adhesives or self-adhesive labels, other than those

recommended by the helmet manufacturer’s instructions.

The MSA LH 350 flying helmet is designed only for helicopter pilots and crew members. It

ensures a maximum comfort and protection.

Available in three sizes to fit head measuring between 52 cm to 64 cm. It incorporates two

visors; and could receive a wide range of communication systems and Night Vision Goggles

supports, available to order. Please contact us for details.

Each helmet is individually serial numbered to ensure correct identification of the helmet and

a correct record of the service life history of the helmet.

Checks should be made following any apparent impact, carried out by our

maintenance department or a specialist.

CONFIDENTIAL INDUSTRY

Ref : 180722 – PP0200175 ind00 4/18

LH 350 F L I G H T H E L M E T

DESCRIPTION OF HELMET

The LH350 helmet shell is made of :

• A one-piece shell in high performance composite fibers. The shell covers a large head

protection zone.

• An expanded polystyrene inner padding for impact absorption. It is covered with a velvet

lining for the user's comfort.

• Custom fit pads are used to fit the helmet to the users headform.

The outside coating is flame retardant.

The inner lining is made up of two comfort spacers : the T shaped spacer and the neck spacer

each of these spacer can be personalized with different foam in 3 thickness (4mm, 8mm and 12mm)

which make it possible to obtain a perfect fit for the user's head form.

The lining elements are made up of different thickness foam inserts covered in a ‘patented‘ wicking

material to draw moisture away from the users skin in hot and humid climates and ensure the user’s

comfort.

These two comfort spacers are attached inside the shell by Velcro strips. Adaptation to the user's

head form is made by choosing the foam thickness inside each spacer.

Two protective visors manufactured are fitted to the LH350 :

• Both visors are mounted on the outside of the helmet shell and fully protected by the hard

cover

• Both visors can be adjusted to suit the users requirements.

The acoustic protection system is made up of :

• Two injection molded thermoplastic earcups, with a recess to accommodate the

communication earphones.

• Two earseals for comfort, ergonomically shaped.

• Specific acoustic foam.

These earcups ensure correct acoustic protection and are fixed inside the shell by Velcro spacers.

The chinstrap is made of a synthetic fire-proof fibre strap with a clipping buckle. A leather chinstrap

covers the strap to ensure user’s comfort at the chin.

A helmet protective bag.

Serial Number, Helmet Log Card and Modification Record.

Every MSA flight helmet is supplied with a helmet log card recording the manufacturing and model

details of the helmet, in addition to recording modifications and Level 3 repairs to the helmet.

Each helmet is individually serial numbered to ensure correct identification of the helmet and a

correct record of the service life history of the helmet.

CONFIDENTIAL INDUSTRY

Ref : 180722 – PP0200175 ind00 5/18

G U A R A N T E E

All of our models, accessories, and spare parts are meticulously inspected before leaving

the factory.

MSA helmets and their options are guaranteed for one year from the date of purchase.

Guarantee provides for parts and labor repair or replacement of the helmet and components arising

from any mechanical or electrical failure or defect which may occur during normal operating

conditions as described in the helmet Instruction Manual supplied with each helmet.

CONFIDENTIAL INDUSTRY

Ref : 180722 – PP0200175 ind00 6/18

PREAMBLE

Important : for any repair install the helmet at least on the helmet protecting bag

Necessary tools :

- 20, 15 and 10 TORX key

- 7 mm combination wrench

- 2 mm hexagonal screw driver

- Flat blade screwdriver

- Threadlocking low strength (LOCTITE 222 or equivalent )

CONFIDENTIAL INDUSTRY

Ref : 180722 – PP0200175 ind00 7/18

1. Chinstrap:

Tools: 20 and 15 TORX keys, 7 mm combination wrench and flat blade screwdriver.

Dismantling duration: 1 minute.

Mounting duration: 2 minutes.

Open the chinstrap.

4 points chinstrap disassembly

Left and right chinstrap dismantle:

1 front fixation points: unscrew the outer screw with the 20 key TORX while maintaining inner

helmet nut with 7 mm combination wrench (remove the nut cap with the screw driver before ),

2 rear fixation points : unscrew the inner helmet screw with the 15 TORX key.

Proceed in the reverse order to reassemble.

Warning: Apply Threadlocking low strength on the inner TORX screw back fixation point before

mounting.

When removing the chin-cup; check that the buckle is correctly positioned, the opened side of

the buckle towards the outside of the helmet.

20 TORX

key

7 mm combination

ench

15 TORX key

Inside detail

CONFIDENTIAL INDUSTRY

Ref : 180722 – PP0200175 ind00 8/18

2. Clothing:

Tools: none.

Dismantling duration: 20 seconds.

Mounting duration: 45 seconds.

LH 350 helmet includes 2 comfort parts and spacers:

• 1 adjustable, comfortable T-shaped spacer with 4 mm,

8mm and 12mm

thick foam,

•

Comfort

neck spacer

with 4 mm,

8mm and 12mm

thick foams,

• Self-gripping spacers for ear cup adjustment.

Those elements are fixed inside the helmet by self gripping tapes.

When changing the foam in the T shaped spacer and in the comfort neck spacer, insure that the

chosen foams are well positioned. Check the presence of the trapezoid insert with the comfort

neck spacer.

4mm thickness foam (no hole)

8mm thickness foam (1 hole)

12mm thickness foam (2 holes)

CONFIDENTIAL INDUSTRY

Ref : 180722 – PP0200175 ind00 9/18

3. Outer visor :

Tools : none.

Dismantling duration: 2 minutes.

Mounting duration: 2 minutes.

Unscrew the 2 captive screws on the right and left sides.

Raised the hard cover by rotating back side the hinge.

Remove the outer visor by sliding outside the hard cover

Proceed in the reverse order to reassemble.

Warning

When replacing the hard cover, ensure that the lug is securely in place beneath the base. See

below.

Screw up the captive screws on the right and left sides.

lug

Opened position

Closed position

hinge

CONFIDENTIAL INDUSTRY

Ref : 180722 – PP0200175 ind00 10/18

4. Inner visor :

Tools : none.

Dismantling duration: 2 minutes.

Mounting duration: 2 minutes.

Lower the inner visor

Unscrew the 2 captive screws on the right and left sides.

Raised the hard cover by rotating back side the hinge

1- Open the left and right base covers by rotating upwards

(do not unscrew anything).

2- Disengage the visor interfaces from their axis of rotation.

Proceed in the reverse order to reassemble.

Warning

When replacing the hard cover, in closed position, ensure that the lug is securely in place

beneath the base.

lug

Screw up the captive screws on the right and left sides.

visor interface

base cover

hinge

Opened position

Closed position

Tabla de contenidos

Otros manuales de Accesorios para motocicletas de MSA

MSA

MSA V-Gard H1 Manual de usuario

MSA

MSA LH 050 Manual de usuario

MSA

MSA F2 X-TREM Manual de usuario

MSA

MSA Gallet F1 XF Manual de usuario

MSA

MSA V-Gard H1 Manual de usuario

MSA

MSA V-GARD 900 Series Manual de usuario

MSA

MSA Gallet F1 XF Manual de usuario

MSA

MSA F2 X-TREM Manual de usuario

MSA

MSA F2 X-TREM Manual de usuario

MSA

MSA GAA Series Manual de usuario

MSA

MSA Cairns XF1 Guía

MSA

MSA Gallet F2XR Manual de mantenimiento

MSA

MSA AUER 3S-Basis Plus Manual de usuario

MSA

MSA Cairns 1010 Manual de usuario

MSA

MSA Gallet F1 XF Guía de instalación y uso

MSA

MSA V-GARD 900 Series Manual de usuario

MSA

MSA Cairns 1010 Manual de usuario

MSA

MSA GAG Series Manual de usuario

MSA

MSA V-Gard Series Manual de usuario

MSA

MSA V-Gard H1 Manual de usuario

MSA

MSA F1S Instrucciones de funcionamiento

MSA

MSA Gallet F1 XF Manual de usuario

MSA

MSA V-Gard Series Manual de usuario

MSA

MSA Cairns XF1 Manual de usuario

Manuales populares de Accesorios para motocicletas de otras marcas

SRC

SRC B-TRK502-01-01-SL Manual de usuario

3M Speedglas 9100 MP Manual de usuario

hepco & becker

hepco & becker 6307520 00 01 Manual de usuario

HOMCOM

HOMCOM AA0-077 Manual de usuario

hepco & becker

hepco & becker 6307558 00 01 Manual de usuario

Wunderkind Custom

Wunderkind Custom 106503-F15 Guía del usuario

Dräger

Dräger HPS 3500 Manual de usuario

M-WAVE

M-WAVE SKI Manual de usuario

Kuryakyn

Kuryakyn 6212 Manual de usuario

hepco & becker

hepco & becker 6507504 00 01 Manual de usuario

Tool it

Tool it PROMAX LCD 9.13G Manual de usuario

Custom Dynamics

Custom Dynamics TruWrapz Manual de usuario

Roof

Roof RO200 CARBON Manual de usuario

Kabuto

Kabuto Japan IBUKI Manual de usuario

PUIG

PUIG 5051 Manual de usuario

rizoma

rizoma ZTH050 Manual de usuario

Joubert

Joubert 10001711 Manual de usuario

Sperian

Sperian Optrel p420 Manual de usuario