Moxa Technologies IKS-6728 Series Manual

P/N: 1802067280011

IKS-6728/IKS-6726 Series

Hardware Installation Guide

Second Edition, May 2012

- 2 -

Package Checklist

The Moxa IKS-6728/IKS-6726 Series industrial rackmount switches are

shipped with the following items. If any of these items are missing or

damaged, please contact your customer service representative for

assistance.

•IKS-6728 or IKS-6726 Switch

•RJ45 to DB9 console port cable

•Protective caps for unused ports

•2 rackmount ears

•Documentation and software CD

•Hardware Installation Guide

•CD-ROM with User’s Manual and SNMP MIB file

•Moxa Product Warranty Statement

Panel Layouts

1. Model name

2. System status LEDs

3. Reset button

4. Serial console port

5. Terminal block for relay output

6. USB storage port

7. 100/1000Base SFP port status LEDs

8. 10/100/1000BaseT(X) or 100/1000Base SFP combo ports

9. 10/100BaseT(X) ports

10. Fast Ethernet Interface Modules

11. Power sockets for AC power inputs

12. Terminal blocks for DC power inputs

13. Grounding screw

- 3 -

Dimensions

Unit = mm (inch)

Fast Ethernet Interface Modules (IM-6700 Series)

Grounding the Moxa Industrial Rackmount Switch

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

ground screw to the grounding surface prior to connecting devices.

Connecting the Power Inputs

The IKS-6726/6728 series of switches supports both 110/220 VAC and

24/48 VDC power supplies.

- 4 -

AC Power Inlets

The connection for PWR1 (power supply 1) and PWR2 (power supply 2)

are located on the rear side (shown below). Be sure to use a standard

power cord with an IEC C13 connector, which is compatible with the AC

power inlet.

DC Power Terminal Blocks

The connection for PWR1 (power supply 1) and PWR2 (power supply 2)

are located on the rear side (shown below).

STEP 1: Insert the negative/positive DC wires into the V-/V+ terminals,

respectively.

STEP 2: To keep the DC wires from pulling loose, use a small flat-blade

screwdriver to tighten the wire-clamp screws on the front of the terminal

block connector.

STEP 3: Insert the plastic terminal block connector prongs into the

terminal block receptor.

Wiring the Relay Contact

Each IKS-6726/6728 switch has one relay output.

FAULT:

The relay contact of the 2-pin terminal block connector is used to detect

user-configured events. The two wires attached to the fault contacts form

an open circuit when a user-configured event is triggered. If a

user-configured event does not occur, the fault circuit remains closed.

RS-232 Connection

The Moxa IKS-6726/6728 has one RS-232 (10-pin RJ45) console port,

located on the front panel. Use either an RJ45-to-DB9 or RJ45-to-DB25

cable to connect Moxa IKS-6726/6728 console port to your PC’s COM port.

You may then use a console terminal program, such as Moxa PComm

Terminal Emulator, to access Moxa IKS-6726/6728’s console

configuration utility.

RJ45 (10-pin) Console Port Pinouts

Description

–

RxD

DSR

GND

–

GND

DTR

TxD

–

- 5 -

The Reset Button

Depress the Reset button for 5 continuous seconds to load the factory

default settings. Use a pointed object, such as a straightened paper clip

or toothpick, to depress the Reset button. This will cause the STATE LED

to blink on and off. The factory default settings are loaded once the

STATE LED stops blinking (after about 5 seconds). At this point, you can

release the Reset button.

LED Indicators

The front panel of the IKS switch contains several LED indicators. The

function of each LED is described in the table below.

LED

Color

State

Description

System LEDs

STATE GREEN On System has passed self-diagnosis test on

boot-up and is ready to run

Blinking

1. System is undergoing the self-diagnosis

test

2. Blink continuously when pressing the

reset button 5 seconds to reset to factory

default

RED

System failed self-diagnosis on boot-up.

PWR1

AMBER

Power is being supplied to the main

module’s power input PWR1

Off Power is not being supplied to the main

module’s power input PWR1

PWR2

AMBER

Power is being supplied to the main

module’s power input PWR2

Off

Power is not being supplied to the main

module’s power input PWR2

FAULT

RED

System is in the event of failure, or is under

quick inspection

Off

System is in normal operation

MSTR/

HEAD

GREEN On When the IKS-6726/6728 is set as the

Master of the Turbo Ring, or as the Head of

the Turbo Chain

Blinking

The IKS-6726/6728 has become the Ring

Master of the Turbo Ring, or the Head of

the Turbo Chain, after the Turbo Ring or

the Turbo Chain is down

Off The IKS-6726/6728 is not the Master of

this Turbo Ring or is set as a Member of the

Turbo Chain

CPLR/TAIL

GREEN

When the IKS-6726/6728 coupling function

is enabled to form a back-

up path, or when

it’s set as the Tail of the Turbo Chain

Blinking

When the Turbo Chain is down

Off When this IKS-6726/6728 switch disables

the coupling function

LED

Color

State

Description

Port Status LEDs

10/100M

GREEN

The corresponding port’s link is active

- 6 -

10/100/

1000M

(TP ports)

Blinking

The corresponding port’s data is being

transmitted

Off

The corresponding port’s link is inactive

100/1000

M (Fiber

Optic

ports)

GREEN

When the IKS-6726/6728 coupling function

is enabled to form a back-

up path, or when

it’s set as the Tail of the Turbo Chain

Blinking

When the Turbo Chain is down

Off When this IKS-6726/6728 switch disables

the coupling function

AMBER

Fiber optic port's 100 Mbps link is active

Blinking

Data is being transmitted at 100 Mbps

Off

Fiber Optic port’s 100 Mbps link is inactive

100M

(Fiber

Optic

ports)

GREEN On The corresponding port’s link is active

Blinking

The corresponding port’s data is being

transmitted

Off The corresponding port’s link is inactive

Specifications

Technology

Standards

IEEE 802.3 for 10BaseT

IEEE 802.3u for 100BaseT(X) and 100BaseFX

IEEE 802.3ab for 1000BaseT(X)

IEEE 802.3z for 1000BaseX

IEEE 802.3x for Flow Control

IEEE 802.1D-2004 for Spanning Tree Protocol

IEEE 802.1w for Rapid STP

IEEE 802.1s for Multiple Spanning Tree Protocol

IEEE 802.1Q for VLAN Tagging

IEEE 802.1p for Class of Service

IEEE 802.1X for Authentication

IEEE 802.3ad for Port Trunk with LACP

Protocols IGMP v1/v2, GMRP, GVRP, SNMPv1/v2c/v3, DHCP

Server/Client, BootP, TFTP, SNTP, SMTP, RARP,

RMON, HTTP, HTTPS, Telnet, SSH, Syslog, DHCP

Option 66/67/82, EtherNet/IP, Modbus/TCP, LLDP,

IEEE 1588 PTP V2, IPv6, NTP Server/Client

MIB

MIB-II, Ethernet-like MIB, P-BRIDGE MIB,

Q-BRIDGE MIB, Bridge MIB, RSTP MIB, RMON MIB

Group 1, 2, 3, 9

Flow Control

IEEE 802.3x flow control, back pressure flow control

Interface

Fast Ethernet 8-port 10/100Base T(X)

2 modular slots for any 8-, or 6-port Interface

Modules with 10/100BaseT(X), 100BaseFX (SC/ST

connector), or 100Base SFP

Gigabit Ethernet

2- or 4-port 10/100/1000BaseT(X) or 100/1000Base

SFP

Console Port

RS-232 (RJ45 connector)

LED Indicators

STATE, PWR1, PWR2, FAULT, MSTR/HEAD,

CPLR/TAIL

Alarm Contact

1 relay output with current carrying capacity of 3 A

- 7 -

@ 30 VDC or 3 A @ 240 VAC

Power Requirements

Input Voltage 24 VDC (18 to 36 V), or 48 VDC (36 to 72 V), or

110/220 VAC (85 to 264 VAC)

Input Current

(without IM-6700

modules installed)

Max. 0.42 A @ 24 VDC

Max. 0.22 A @ 48 VDC

Max. 0.32/0.16 A @ 110/220 VAC

Overload Current

Protection

Present

Reverse Polarity

Protection

Present

Physical Characteristics

Housing

IP30 protection

Dimensions

440 x 44 x 280 mm (17.32 x 1.37 x 11.02 in)

Weight

4100 g

Installation

19’’ rack mounting

Environmental Limits

Operating Temp.

-40 to 75°C (-40 to 167°F)

Storage Temp.

-40 to 85°C (-40 to 185°F)

Ambient Relative

Humidity

5 to 95% (non-condensing)

Standards and Certifications

Safety

UL 60950-1 (Pending), EN 60950-1 (Pending)

EMI

FCC Part 15 Subpart B Class A, EN 55022 Class A

Rail Traffic

EN50121-4

Warranty

Warranty Period

5 years

Details

See www.moxa.com/warranty

Rack Mounting Instructions

1. Elevated Operating Ambient: If installed in a closed or multi-unit

rack assembly, the operating ambient temperature of the rack

environment may be greater than room ambient. Therefore,

consideration should be given to installing the equipment in an

environment compatible with the maximum ambient temperature

(Tma) specified by the manufacturer.

2. Reduced Air Flow: Installation of the equipment in a rack should

be such that the amount of air flow required for safe operation of the

equipment is not compromised.

3. Mechanical Loading: Mounting of the equipment in the rack

should be such that a hazardous condition is not achieved due to

uneven mechanical loading.

4. Circuit Overloading: Consideration should be given to the

connection of the equipment to the supply circuit and the effect that

overloading of the circuits might have on overcurrent protection and

supply wiring. Appropriate consideration of equipment nameplate

ratings should be used when addressing this concern.

5. Reliable Grounding: Reliable grounding of rack-mounted

equipment should be maintained. Particular attention should be

given to supply connections other than direct connections to the

branch circuit (e.g. use of power strips)."

- 8 -

Restricted Access Locations

•This equipment is intended to be used in Restricted

Access Locations, such as a computer room, with

access limited to SERVICE PERSONAL or USERS

who have been instructed on how to handle the

metal chassis of equipment that is so hot that

special protection may be needed before touching it. The location

should only be accessible with a key or through a security identity

system.

•External metal parts of this equipment are extremely hot!! Before

touching the equipment, you must take special precautions to protect

your hands and body from serious injury.

Technical Support Contact Information

www.moxa.com/support

Moxa Americas:

Toll

-free: 1-888-669-2872

Tel:

1-714-528-6777

Fax:

1-714-528-6778

Moxa China (Shanghai office):

Toll

-free: 800-820-5036

Tel:

+86-21-5258-9955

Fax:

+86-21-5258-5505

Moxa Europe

Tel:

+49-89-3 70 03 99-0

Fax:

+49-89-3 70 03 99-99

Moxa Asia

-Pacific:

Tel:

+886-2-8919-1230

Fax:

+886-2-8919-1231

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Moxa Technologies

Moxa Technologies

Moxa Technologies ICS-G7 Series Manual de usuario

Moxa Technologies

Moxa Technologies EtherDevice EDS-305-T Manual

Moxa Technologies

Moxa Technologies EDS-600 Series Manual

Moxa Technologies

Moxa Technologies IKS-G6524A Manual de usuario

Moxa Technologies

Moxa Technologies PowerTransPT-7528 Series Manual

Moxa Technologies

Moxa Technologies PT-508 Series Manual

Moxa Technologies

Moxa Technologies EDS-316 Series Manual de usuario

Moxa Technologies

Moxa Technologies EtherDevice EDS-405A-PN Manual de usuario

Moxa Technologies

Moxa Technologies TN-5510A Series Manual de usuario

Moxa Technologies

Moxa Technologies IEX-408E-2VDSL2 series Manual de usuario

Moxa Technologies

Moxa Technologies EDS-G512E-8PoE Manual

Moxa Technologies

Moxa Technologies EtherDevice EDS-518A-T Manual

Moxa Technologies

Moxa Technologies EtherDevice EDS-G509-T Manual

Moxa Technologies

Moxa Technologies PT-G7828 Manual de usuario

Moxa Technologies

Moxa Technologies IKS-6726-8PoE Series Manual

Moxa Technologies

Moxa Technologies EDS-408A Manual de usuario

Moxa Technologies

Moxa Technologies NPORT 6610 Manual de usuario

Moxa Technologies

Moxa Technologies NE-4100 Series Manual de usuario

Moxa Technologies

Moxa Technologies IKS-6726-8PoE Series Manual

Moxa Technologies

Moxa Technologies PowerTransPT-7728-PTP Manual de usuario

Moxa Technologies

Moxa Technologies ToughNet TN-5524-8PoE-P24-T Manual de usuario

Moxa Technologies

Moxa Technologies EtherDevice EDS-208A series Manual

Moxa Technologies

Moxa Technologies EDS-510E Series Manual

Moxa Technologies

Moxa Technologies PT-7728 Series Manual

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario