Moxa Technologies NPort W2150A-T Manual de usuario

– 1 – – 2 – – 3 –

P/N: 1802021503010

NPort W2150A/W2250A Series

Quick Installation Guide

First Edition, April 2012

1. Overview

The NPort W2150A/W2250A wireless device servers are an ideal

choice for connecting serial devices such as PLCs, meters, and

sensors to an IP-based wireless LAN or Ethernet LAN.

Features

•Link any serial device to an IEEE 802.11a/b/g network.

•1 and 2-port RS-232/422/485 models, up to 921.6 Kbps.

•Web-based configuration over Ethernet or wireless LAN.

•Enhanced security for remote configuration with HTTPS, SSH.

•Secure data access with WEP, WPA, WPA2.

•Built-in WLAN site survey tool.

•Fast roaming when signal strength is weak.

•Per-port offline port buffering and serial data log.

•Dual power inputs via power jack and terminal block.

2. Package Checklist

Before installing the NPort W2150A/W2250A device server, verify

that the package contains the following items:

•1 NPort W2150A, NPort W2150A-T, NPort W2250A, or

NPort W2250A-T.

•Document and Software CD.

•RJ45 to RJ45 cross-over Ethernet cable.

•Warranty Statement.

•Quick Installation Guide.

Optional Accessories

•DK-35A (35 mm DIN-Rail Mounting Kit).

•Power jack to terminal block power cable

(P/N: 9199000000900).

Note: Notify your sales representative if any of the above items are

missing or damaged.

3. Hardware Introduction

The NPort W2150A models have one serial port, and the NPort

W2250A models have two serial ports. All models support

RS-232/422/485 operation with DB9 connectors, and include one

10/100M Ethernet port.

NPort W2150A/W2150A-T

NPort W2250A/W2250A-T

Reset Button—The reset button is used to load factory default

settings. Use a pointed object to hold the reset button down for 5

seconds to load factory defaults.

End Panel LED Indicators

Name

Color

Function

Ethernet

Orange

10 Mbps Ethernet connection

Green

100 Mbps Ethernet connection

Off

Ethernet cable is disconnected

Top Panel LED Indicators

Name

Color

Function

Ready

Red

Steady on:

Power is on and NPort is booting

Blinking:

IP conflict or DHCP/BOOTP server

did not respond properly

Green

Steady on:

NPort is functioning normally

Blinking: NPort is responding to Locate

function

Off

Power is off or a power error condition exists

WLAN Green

Steady on:

Wireless enabled

Blinking:

NPort can’t establish WLAN

connection with AP

(Infrastructure) or station

(Ad-Hoc)

Off

Wireless not enabled

Name

Color

Function

Serial 1

Serial 2

Orange

Serial port is receiving data

Green

Serial port is transmitting data

Off

No data is flowing to or from the serial port

Signal

Strength

Red

1 Red -

the signal strength is between 0%

to 20%

2 Red - the signal strength is between 21%

to 40%

Green

3 Green -

the signal strength is between 41%

to 60%

4 Green -

the signal strength is between 61%

to 80%

5 Green -

the signal strength is between 81%

to 100%

4. Pull High/Low Resistors and Terminal

Resistor for RS-422/485

You may need to set the pull high/low resistors when termination

resistors are used for certain RS-422 or RS-485 environments.

S2(Serial 1)

S3(Serial 2)

DIP 1

DIP 2

DIP 3

DIP 4

Pull high

Resistor

Pull low

Resistor

Terminal

Resistor

Reserved

1K Ω

120 Ω

-----

OFF

*150K Ω

*N/A

-----

* Default

S3 is for NPort W2250A only.

– 4 – – 5 – – 6 –

www.moxa.com/support

The Americas:

+1-714-528-6777 (toll-free: 1-888-669-2872)

Europe:

+49-89-3 70 03 99-0

Asia-Pacific:

+886-2-8919-1230

China:

+86-21-5258-9955 (toll-free: 800-820-5036)

NOTE

Do not use the 1 KΩ setting while in RS

232 mode. Doing

so will degrade the RS

232 signals and reduce the effective

communication distance.

5. First-time Hardware Installation

STEP 1:

After removing the NPort W2150A/W2250A from the box,

use a cross

-over Ethernet cable to connect the NPort’s

RJ45 Ethernet port directly to your computer’s Ethernet

port.

STEP 2:

Attach the power adaptor to the NPort and then plug the

adaptor into an electrical outlet.

STEP 3:

Configure the NPort W2150A/W2250A through the

Ethernet port. See the next section for software

installation information.

NOTE

You must connect the Ethernet cable first before powering

up your NPort

6. Software Installation Information

Insert the Document & Software CD into your PC. A window should

open with several options displayed:

•Click [Install COM Driver] and follow the on-screen

instructions to install the COM drivers.

•Click [Documents] and select “NPort W2150A/W2250A

Series User’s Manual” to view the user’s manual.

•Click [Install UTILITY] and follow the on-screen instructions

to install the NPort Search Utility. This utility can be used to

search for NPort W2150A/W2250A units on the network.

7. Setting the IP Address

The factory default IP settings are assigned as follows:

LAN: Static; IP = 192.168.126.254; netmask = 255.255.255.0

WLAN: Static; IP = 192.168.127.254; netmask = 255.255.255.0

If the NPort is configured for DHCP but the DHCP server cannot be

found, the NPort will use factory default IP settings.

NOTE

If you have forgotten the NPort’s IP address, use the NPort

Search Utility from your PC to locate the NPort. Aft

searching the LAN for NPort units, the NPort Search Utility

will display the IP address of each unit.

NOTE

Only one network interface can be active at a time. If the

Ethernet link is active, the WLAN will be inactive. If the

WLAN is active, the Ethernet link will be inactive.

Open the web console to make configuration changes as follows:

STEP 1:

Open your web browser.

STEP 2:

In the address bar, enter 192.168.126.254 (the default

IP address).

STEP 3:

The web console will open, and the current configuration

settings are shown.

STEP 4:

For first time use, click the Wizard

in the left navigation

panel. The wizard will prompt you to configure the IP

address, SSID, and security mode. For other settings,

use the factory defaults or modify the settings for your

application.

8. Pin Assignments and Cable Wiring

Pin RS-232

RS-422,

4w RS-485

2w RS-485

DCD

TxD-(A)

---

RXD

TxD+(B)

---

TXD

RxD+(B)

Data+(B)

DTR

RxD-(A)

Data-(A)

GND

DSR

---

RTS

---

CTS

---

Female DB9 to Male DB9

Female DB9 to Male DB25

9. Specifications

Power Requirements

Power Input

12 to 48 VDC

Power Consumption

237mA @ 12V

Power Connector

Screw type power jack and terminal

block

Physical Characteristics

Material

Aluminum sheet metal (1 mm)

Dimensions

77 × 111 × 26 mm (no ears, no antenna)

100 × 111 × 26 mm

(with ears, no antenna)

Antenna Length

109 mm

Magnetic Isolation

1.5 KV magnetic isolation built-in

Environmental Limits

Operating Temperature

Standard Models:

0 to 55°C (32 to 131°F), 5 to 95%RH

Wide Temp. Model

-40 to 75°C (-40 to 167°F), 5 to 95%RH

Storage Temperature

-40 to 85°C (-40 to 185°F), 5 to 95%RH

Regulatory Approvals

EMC

CE: EN 55022 Class A/EN 55024

ETSI EN 301 489-17,

ETSI EN 301 489-1

FCC:

FCC Part 17 Subpart B, Class A

FCC Part 15 Subpart B, Class A

Safety

UL:

UL 60950-1

LVD

: EN 60950-1

DSPR: ARIB-STD 33, ARIB-STD 66

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Servidor de Moxa Technologies

Moxa Technologies

Moxa Technologies NPort 6450 Series Manual de usuario

Moxa Technologies

Moxa Technologies NPort 6450 Series Manual de usuario

Moxa Technologies

Moxa Technologies NPort 5110 Series Manual de usuario

Moxa Technologies

Moxa Technologies CN2610 series Manual de usuario

Moxa Technologies

Moxa Technologies NPort 5210 Manual de usuario

Moxa Technologies

Moxa Technologies ioLogik R2110 Series Manual de usuario

Moxa Technologies

Moxa Technologies NPort P5150A Series Manual de usuario

Moxa Technologies

Moxa Technologies NPort 5250A Manual de usuario

Moxa Technologies

Moxa Technologies NPort IA5150A Manual de usuario

Moxa Technologies

Moxa Technologies NPort W2250 Plus Series Manual de usuario

Moxa Technologies

Moxa Technologies CN2600 Series Manual de usuario

Moxa Technologies

Moxa Technologies NPort 5600-8-DT Manual de usuario

Moxa Technologies

Moxa Technologies NPort 5100 Series Manual de usuario

Moxa Technologies

Moxa Technologies NPort 6250 Series Manual de usuario

Moxa Technologies

Moxa Technologies NPort W2150 Plus Manual de usuario

Moxa Technologies

Moxa Technologies CN2600 Series Manual de usuario

Moxa Technologies

Moxa Technologies NPort W2150 Plus Manual de usuario

Moxa Technologies

Moxa Technologies NPort IA5450A Manual de usuario

Moxa Technologies

Moxa Technologies CN2610 series Manual de usuario

Moxa Technologies

Moxa Technologies NPort P5250A Series Manual de usuario

Moxa Technologies

Moxa Technologies NPort S8000 Series Manual de usuario

Moxa Technologies

Moxa Technologies NPort 5600-8-DT Manual de usuario

Moxa Technologies

Moxa Technologies NPort 6150 Series Manual de usuario

Moxa Technologies

Moxa Technologies MIINEPORT E1 Manual de usuario

Manuales populares de Servidor de otras marcas

HP AlphaServer ES47 Manual de usuario

Dell

Dell PowerEdge R410 Manual de usuario

PowerNAS

PowerNAS CMA Manual de usuario

Supero

Supero FatTwin F617R3-FT Manual de usuario

MSI

MSI P1-109N-L70 Manual de usuario

Dell

Dell PowerEdge XE9640 Manual

Dell

Dell PS4100 Instrucciones de montaje

EtroVISION

EtroVISION EV3151 Manual de usuario

NEC

NEC Express5800/T110j Manual de usuario

HP ProLiant Gen9 Manual de usuario

Compaq

Compaq ProLiant 3000 Manual

Dell

Dell PowerEdge 3YPMN Manual de usuario

iRobo

iRobo IPC2U Manual de usuario

Nortel

Nortel 1000 Con?guration guide Manual de usuario

Asus

Asus AP7500 Manual de operación y mantenimiento

Avid Technology

Avid Technology AirSpeed 5000 Manual de usuario

HP Integrity rx2600 Guía de instalación

Milestone

Milestone Husky IVO 350T Manual de usuario