Moxa Technologies AIG-100 Series Manual de usuario

P/N: 1802001017010

*1802001017010*

AIG-100 Series

Quick Installation Guide

Version 1.0, October 2022

Technical Support Contact Information

www.moxa.com/support



- 2 -

Overview

Moxa AIG-100 Series can be used as smart edge gateways for data

preprocessing and transmission. The AIG-100 Series focuses on IIoT-

related energy applications and supports various LTE bands and

protocols.

Package Checklist

Before installing the AIG-100, verify that the package contains the

following items:

•AIG-100 gateway

•DIN-rail mounting kit (preinstalled)

•Power jack

•3-pin terminal block for power

•Quick installation guide (printed)

•Warranty card

NOTE

Notify your sales representative if any of the above items are

missing or damaged.

Panel Layout

The following figures show the panel layouts of the AIG-100 models:

AIG-101-T

- 3 -

AIG-101-T-AP/EU/US

LED Indicators

LED Name

Status

Function

SYS

Green

Power is ON

Off

Power is OFF

Green

(blinking)

The gateway will reset to the default

configuration

LAN1/LAN2

Green

10/100 Mbps Ethernet mode

Off

Ethernet port is not active

COM1/COM2

Orange

Serial port is transmitting or receiving data

LTE

Green

Cellular connection has been established

NOTE:

Three levels based on the signal strength

1 LED is ON: Poor signal quality

2 LEDs are ON: Good signal quality

All 3 LEDs are ON: Excellent signal quality

Off

Cellular interface is not active

Reset Button

Reboots or restores the AIG-100 to factory default settings. Use a

pointed object, such as a straightened paper clip, to activate this

button.

•System reboot: Press and hold the Reset button for one second or

less.

•Reset to the default configuration: Press and hold the Reset button

till the SYS LED blinks (approximately seven seconds).

- 4 -

Installing the AIG-100

The AIG-100 can be mounted on to a DIN rail or on to a wall. The DIN-

rail mounting kit is attached by default. To order a wall-mounting kit,

contact a Moxa sales representative.

DIN-rail Mounting

To mount the AIG-100 on to a DIN rail, do the following:

1. Pull down the slider of the DIN-rail bracket at the back of the unit

2. Insert the top of the DIN rail into the slot just below the upper

hook of the DIN-rail bracket.

3. Latch the unit firmly on to the DIN rail as shown in the illustrations

below.

4. Once the computer is mounted properly, you will hear a click and

the slider will rebound back into place automatically.

Wall Mounting (optional)

The AIG-100 can also be wall mounted. The wall-mounting kit needs to

be purchased separately. Refer to the datasheet for more information.

1. Fasten the wall-mounting kit to the AIG-100 as shown below:

2. Use two screws to mount the AIG-100 on to a wall.

These two screws are not included in the wall-mounting kit and

- 5 -

must be purchased separately. Refer to the detailed specifications

below:

Head Type

:flat

Head Diameter

>5.2 mm

Length

>6 mm

Thread Size

:M3 x 0.5 mm

Connector Description

Power Terminal Block

A person trained for the job should install the wiring for the input

terminal block. The wire type should be copper (Cu) and only 28-18

AWG wire size and torque value 0.5 N-m should be used.

Power Jack

Connect the power jack (in the package) to the AIG-100’s DC terminal

block (on the bottom panel), and then connect the power adapter. It

takes several seconds for the system to boot up. Once the system is

ready, the SYS LED will light up.

NOTE

The product is intended to be supplied by a UL Listed Power

Unit marked "L.P.S." (or "Limited Power Source") and is rated

-36 VDC, 0.8 A min., Tma = 70°C (min). If you need further

help

with purchasing the power source, please contact Moxa for

further information.

Grounding

Grounding and wire routing help limit the effects of noise because of

electromagnetic interference (EMI). There are two ways to connect the

AIG-100 grounding wire to the ground.

1. Through the SG (Shielded Ground):

The SG contact is the left-most contact in the

3-pin power terminal block connector when

viewed from the angle shown here. When you

connect to the SG contact, the noise will be

routed through the PCB and the PCB copper

pillar to the metal chassis.

2. Through the GS (Grounding Screw):

The GS is next to the power connector. When

you connect to the GS wire, the noise is

routed directly through the metal chassis.

NOTE

The grounding wire should have a minimum diameter of

3.31 mm

- 6 -

NOTE

If using a Class I adapter, the power cord must be connected to

a socket-outlet with an earthing connection.

Ethernet Port

The 10/100 Mbps Ethernet port uses the RJ45 connector. The pin

assignment of the port is as below:

Signal

Tx+

Tx-

Rx+

–

Rx-

–

Serial Port

The serial port uses the DB9 male connector. Software can configure it

for the RS-232, RS-422, or RS-485 mode. The pin assignment of the

port is as below:

RS-232

RS-422

RS-485

DCD

TxD-(A)

–

RxD

TxD+(B)

–

TxD

RxD+(B)

Data+(B)

DTR

RxD-(A)

Data-(A)

GND

DSR

–

RTS

–

CTS

–

SIM Card Socket

The AIG-100-T-AP/EU/US comes with two nano-SIM card sockets for

cellular communication. The nano-SIM card sockets are on the same

side as the antenna panel. To install the cards, remove the screw and

the protection cover to access the sockets, and then insert the nano-

SIM cards into the sockets directly. You will hear a click when the cards

are in place. The left socket is for SIM 1 and the right socket is for SIM

2. To remove the cards, push the cards in before releasing them.

RF Connectors

The AIG-100 comes with RF connectors to the following interfaces.

- 7 -

Cellular

The AIG-100-T-AP/EU/US models come with a built-in cellular module.

You must connect the antenna to the SMA connector before you can

use the cellular function. The C1 and C2 connectors are interfaces to

the cellular module. For additional details, refer to the AIG-100 Series

datasheet.

GPS

The AIG-100-T-AP/EU/US models come with a built-in GPS module. You

must connect the antenna to the SMA connector with the GPS mark

before you can use the GPS function.

SD Card Socket

The AIG-100 models come with a SD-card socket for storage

expansion. The SD card socket is next to the Ethernet port. To install

the SD card, remove the screw and the protection cover to access the

socket, and then insert the SD card into the socket. You will hear a click

when the card is in place. To remove the card, push the card in before

releasing it.

USB

The USB port is a type-A USB 2.0 port, which can be connected to Moxa

UPort models to extend the serial port capacity.

Real-time Clock

A lithium battery powers the real-time clock. We strongly recommend

that you do not replace the lithium battery without the help of a Moxa

support engineer. If you need to change the battery, contact the Moxa

RMA service team.

ATTENTION

There is

a risk of explosion if the battery is replaced with an

incorrect type

of battery. Dispose of

used batteries according to

the instructions in the warranty card.

Access to the Web Console

You can log in to the web console by default IP through the web

browser. Please ensure your host and AIG are under the same subnet.

•LAN1: https://192.168.126.100:8443

•LAN2: https://192.168.127.100:8443

When you log in to the web console, the default account and password:

•Default account: admin

•Default password: admin@123

Otros manuales para AIG-100 Series

Tabla de contenidos

Otros manuales de Puerta de Moxa Technologies

Moxa Technologies

Moxa Technologies MGate MB3480 Manual de usuario

Moxa Technologies

Moxa Technologies MGate 5102-PBM-PN-T Manual de usuario

Moxa Technologies

Moxa Technologies MGate MB3000 Modbus Manual de usuario

Moxa Technologies

Moxa Technologies MGate 5217 Series Manual de usuario

Moxa Technologies

Moxa Technologies AIG-501-T-AZU-LX Manual de usuario

Moxa Technologies

Moxa Technologies MGate 5102-PBM-PN Manual de usuario

Moxa Technologies

Moxa Technologies MGate 5114 Manual de usuario

Moxa Technologies

Moxa Technologies MGate 5114 Manual de usuario

Moxa Technologies

Moxa Technologies MGate 5122 Series Manual de usuario

Moxa Technologies

Moxa Technologies MGate 5121 Series Manual de usuario

Moxa Technologies

Moxa Technologies OnCell G3100 Series Manual de usuario

Moxa Technologies

Moxa Technologies NPort 4511 Manual de usuario

Moxa Technologies

Moxa Technologies MGate 5111 Manual de usuario

Moxa Technologies

Moxa Technologies NPort PCG Manual

Moxa Technologies

Moxa Technologies MGate MB3270I Manual de usuario

Moxa Technologies

Moxa Technologies MGate MB3180 Manual de usuario

Moxa Technologies

Moxa Technologies MGate MB3180 Manual de usuario

Moxa Technologies

Moxa Technologies MGate MB3000 Modbus Manual de usuario

Moxa Technologies

Moxa Technologies MGate 5105-MB-EIP Manual de usuario

Moxa Technologies

Moxa Technologies MGate 5135 Series Manual de usuario

Moxa Technologies

Moxa Technologies OnCell G3111-HSPA series Manual de usuario

Moxa Technologies

Moxa Technologies Mgate MB3660 Manual de usuario

Moxa Technologies

Moxa Technologies SMG-6100 Manual de usuario

Moxa Technologies

Moxa Technologies MRC-1002 Series Manual de usuario

Manuales populares de Puerta de otras marcas

LST

LST M500RFE-AS Manual de usuario

Kinnex

Kinnex Media Gateway Manual de usuario

2N Telekomunikace

2N Telekomunikace 2N StarGate Manual de usuario

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manual de usuario

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manual de usuario

Telsey

Telsey CPVA 500 - SIP Manual de usuario

RTA

RTA 460A-NNA4 Hoja de especificaciones

Shaw

Shaw Gateway HDPVR Manual de usuario

ABB

ABB VSN900 Guía de inicio rápido

Commander

Commander Pulse Manual de usuario

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manual de usuario

NETGEAR

NETGEAR C6300BD Manual de usuario

Amit

Amit CDW531AM Manual de usuario

HMS

HMS Netbiter EasyConnect EC150 Manual de usuario

Huawei

Huawei EchoLife HG620 Manual de usuario

AT&T

AT&T U-verse 3801 Manual de uso y cuidado

Logic IO

Logic IO RTCU MX2 turbo Manual de usuario

Suttle

Suttle MediaMAX MXM-521 Manual de usuario