Moxa Technologies UC-2200A Series Manual de usuario

P/N: 1802022220011

*1802022220011*

UC-2200A Series

Quick Installation Guide

Version 1.1, November 2023

Technical Support Contact Information

www.moxa.com/support



- 2 -

Overview

The UC-2200A computing platform is designed for embedded data-

acquisition applications. The UC-2200A computer comes with two RS-

232/422/485 serial ports, two 10/100/1000 Mbps Ethernet ports, and a

Mini PCIe socket to support cellular modules. These versatile

communication capabilities let users efficiently adapt the UC-2200A to a

variety of complex communications solutions.

Package Checklist

Before installing the UC-2200A, verify that the package contains the

following items:

•UC-2200A Series computer

•3 round stickers for the screws to preventing tampering

•Quick installation guide (printed)

•Warranty card

IMPORTANT!

Notify your sales representative if any of the above items are

missing or damaged.

Panel Layouts

The following figures show the panel layouts of the UC-2200A:

Top Panel View

- 3 -

Bottom Panel View

Front Panel View

- 4 -

LED Indicators

LED

Status

Function

Power

Green

Power plugged in

OFF

Power is OFF

SW Ready/

Programmable

Yellow System is ON and the computer is working

normally

OFF

System is not ready.

USB/

Programmable

Green USB device is connected and working

normally

OFF

USB device is not connected

SD/

Programmable

Green

Micro SD card inserted and working

normally

OFF

Micro SD card is not detected.

Wireless Signal

Strength/

Programmable

Yellow

The number of glowing LEDs indicates the

signal strength:

2 (both Yellow): Excellent

1 (Yellow): Poor

1 (Yellow, blinking, heartbeat): Very Poor

OFF

Wireless module is not detected.

Serial Tx Green Steady ON: Serial 1/2 not working normally

Blinking: Serial 1/2 transmitting data

OFF

Serial 1/2 not used

Serial Rx

Yellow

Steady ON: Serial 1/2 working normally

Blinking: Serial 1/2 receiving data

OFF

Serial 1/2 not being used.

LAN

Green

Steady ON: A 10/100 M link has been

established

Blinking: Receiving or Transmitting data

Yellow Steady ON: A 1000 M link has been

established

Blinking: Receiving or Transmitting data

OFF

No Ethernet connection

- 5 -

Installing the UC-2200A

DIN-rail Mounting

The stainless-steel DIN-rail mounting plate comes attached to the

product’s casing (the specification for the screws is M3 x 6 mm). To

mount the UC-2200A on to a DIN rail, make sure that the stiff metal

spring is facing upwards and follow these steps.

1. Insert the top of the DIN rail into the slot

just below the upper hook of the DIN-rail

bracket.

2. Latch the unit firmly onto the DIN rail as

shown in the illustrations below:

- 6 -

Wall Mounting (optional)

The UC-2200A can be mounted using a wall-mounting kit, which needs

to be purchased separately. Follow these steps to mount the computer

on to a wall:

Step 1: Use four screws (M3 x 4

mm)

to fasten the wall-mounting

brackets on the

left panel of the

computer.

Step 2: Use another four screws

(M3 x

6 mm) to mount the

computer on a wall or a cabinet.

Connector Descriptions

Power Connector

Connect the power jack (in the package) to the UC-2200A’s DC

terminal block (located on the top panel), and then connect the power

adapter. It takes about 30 seconds for the system to boot up. Once the

system is ready, the Power LED will light up.

ATTENTION

The wiring for the input terminal block should be installed by a

skill

ed person. The wire type should be copper (Cu), wire size

should be

14 to 16 AWG, and a torque of 0.19 n-m should be

used for V+, V

-, and GND connections. The wire size of the

power input and earthing conductor should be the same.

WARNING

The product is intended to be supplied by a UL Listed Power

Unit marked "L.P.S." (or "Limited Power Source") and is rated

to 24 VDC, 0.9 A min., Tma = 75°C (min). If you need

further help with purchasing the power source, please contact

Moxa for further information.

WARNING

The means of power cord of adapter should be connected to a

socket-outlet with earthing connection.

- 7 -

WARNING

EXPLOSION HAZARD!

Do not disconnect equipment unless the power has been

removed or the area is known to be non-hazardous.

Grounding the UC-2200A

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI).

SG: The Shielded Ground (sometimes called

Protected Ground) contact is the

right-most

contact

of the 3

-pin power terminal block connector when

viewed from the angle shown here. Connect the SG

wire to an appropriate grounded metal surface.

Ethernet Ports

The two 10/100/1000 Mbps Ethernet ports (LAN 1 and LAN 2) come

with RJ45 connectors. The pin diagram of the ports is given below:

10/100 Mbps

1000 Mbps

Signal

Tx+

Tx-

Rx+

–

Rx-

–

Definition

TRD(0)+

TRD(0)-

TRD(1)+

TRD(2)+

TRD(2)-

TRD(1)-

TRD(3)+

TRD(3)-

Serial Ports

The two serial ports (P1 and P2) come with terminal-block connectors.

Each port can be configured by software for the RS-232, RS-422, or

RS-485 mode. The pin assignments for the ports are given below:

RS-232

RS-422

RS-485

TXD

TXD+

–

RXD

TXD-

–

RTS

RXD+

D+

CTS

RXD-

D-

GND

- 8 -

Micro SD/SIM Card Sockets

The UC-2200A comes with a Micro SD socket for storage expansion and

a SIM card socket for cellular communication. The Micro SD card and

SIM card sockets are located on the lower part of the front panel. To

install the cards, remove the screw and the protection cover to access

the sockets and insert the Micro SD card or the SIM card into the

sockets. Make sure you insert the cards in the correct direction. Refer

to the instructions above the socket. You will hear a click when the

cards are in place. To remove the cards, push the cards in before

releasing them.

Console Port

The console port is an RS-232 port that can be connected to a 4-pin pin

header cable. You can use this port for debugging or firmware upgrade.

The console port is located on the top panel of the device and is

accessible after removing the cover of the slot.

Signal

TxD

RxD

GND

USB Port

The USB 2.0 port is located at the lower part of the front panel. By

default, the USB auto-mount is disable. If enabled, the USB storage is

mounted at /media/USB_P1 /media/USB_P2.

Antenna Connectors

There are three antenna connectors on

the front panel of the UC

2200A. W1 and

W2 are for cellular modules.

A GPS

antenna connector is located

at the top

of the front panel. All three connectors

are of SMA type.

- 9 -

Real-time Clock

The real-time clock in the UC-2200A is powered by a lithium battery.

We strongly recommend that you do not replace the lithium battery

without the help of a Moxa support engineer. If you need to change the

battery, contact the Moxa RMA service team.

ATTENTION

There is

a risk of explosion if the battery is replaced with an

incorrect type

of battery. Replace only with the same or

equivalent type recommended by the manufacturer.

Dispose of used batteries according to the manufacturer’s

instructions.

Placing a Round Sticker on a Screw

Three round stickers are included in the product package. Stick one of

them on to an external screw as indicated in the figure below to help

detect unauthorized access and tampering.

Follow these steps to place the stickers.

1. Use a cloth to clean the surface of the screws with a 75% alcohol

solution.

2. Use a tweezer to place the stickers.

3. Press the sticker down on to the screw with 15 psi (pound/square

inch) pressure for at least 15 seconds.

4. Keep the device at room temperature for 24 hours before

deploying the devices in harsh environments.

NOTE

1. Place the stickers carefully as they are thin and fragile.

The ideal environment for the stickers to be stored in is

22°C (72°F) and 50% relative humidity.

Keep the extra two stickers in a safe place so that only

authorized persons can access them.

- 10 -

Specifications

Input Current

Models Without Built-in LTE:

600 mA @ 12 VDC

300 mA @ 24 VDC

Models With Built-in LTE:

900 mA @ 12 VDC

450 mA @ 24 VDC

Input Voltage

12 to 24 VDC (3-pin terminal block, V+, V-, SG)

Power

Consumption

Models Without Built-in LTE:

4.5 W (w/o external USB device attached)

7.2 W (external USB device attached)

Models With Built-in LTE:

7.8 W (w/o external USB device attached)

10.5 W (external USB device attached)

Operating

Temperature

Models Without Built-in LTE:

-40 to 75°C (-40 to 167°F)

Models With Built-in LTE:

-40 to 70°C (-40 to 158°F)

Storage

Temperature

-40 to 80°C (-40 to 176°F)

Accessing the UC-2200A Using a PC

You can use a PC to access the UC-2200A by one of the following

methods:

A. Through the serial console port with the following settings:

Baudrate=115200 bps, Parity=None, Data bits=8, Stop bits

=1, Flow Control=None

ATTENTION

Remember to choose the “VT100” terminal type. Use the

console cable to connect a PC to the

UC-2200A's serial console

port

B. Using SSH over the network. Refer to the following IP addresses

and login information:

Default IP Address

Netmask

LAN 2

192.168.4.127

255.255.255.0

Password: moxa

Otros manuales para UC-2200A Series

Tabla de contenidos

Otros manuales de De oficina de Moxa Technologies

Moxa Technologies

Moxa Technologies UC-7408 series Manual de usuario

Moxa Technologies

Moxa Technologies V2406A Series Instrucciones de uso

Moxa Technologies

Moxa Technologies MC-1200 Series Manual de usuario

Moxa Technologies

Moxa Technologies UC-8580-LX Manual de usuario

Moxa Technologies

Moxa Technologies DA-682A-DPP Series Manual de usuario

Moxa Technologies

Moxa Technologies UC-1200A Series Instrucciones de uso

Moxa Technologies

Moxa Technologies THINKCORE W311 Instrucciones de uso

Moxa Technologies

Moxa Technologies UC-3100 Series Manual de usuario

Moxa Technologies

Moxa Technologies V2406C Series Manual de usuario

Moxa Technologies

Moxa Technologies UC-8112-ME-T Series Manual de usuario

Moxa Technologies

Moxa Technologies V2403 Series Manual de usuario

Moxa Technologies

Moxa Technologies UC-8410 Manual de usuario

Moxa Technologies

Moxa Technologies ThinkCore V481 Manual de usuario

Moxa Technologies

Moxa Technologies IA261 Instrucciones de uso

Moxa Technologies

Moxa Technologies DA-681-I-SP-XPE Manual de usuario

Moxa Technologies

Moxa Technologies UC-7400 Manual de usuario

Moxa Technologies

Moxa Technologies V2406A Series Manual

Moxa Technologies

Moxa Technologies V2416 Series Manual de usuario

Moxa Technologies

Moxa Technologies THINKCORE W311 Manual de usuario

Moxa Technologies

Moxa Technologies ThinkCore V481 Instrucciones de uso

Moxa Technologies

Moxa Technologies V2406 Manual de usuario

Moxa Technologies

Moxa Technologies DA-660-8-LX Manual de usuario

Moxa Technologies

Moxa Technologies THINKCORE W345 Manual de usuario

Moxa Technologies

Moxa Technologies DA-820C Series Manual de usuario

Manuales populares de De oficina de otras marcas

HP m9060n - Pavilion - Elite Hoja de especificaciones

Asus

Asus E210 Series Manual de usuario

Dell

Dell Inspiron 600m Manual de usuario

Dell

Dell Inspiron 3662 Manual de usuario

TotalFlow

TotalFlow uFLO Manual de usuario

HP Presario SV7000 - Desktop PC Manual de usuario

HP ProDesk 400 G5 Manual

Logitech

Logitech MK320 Manual de usuario

Dell

Dell XPS 730 H2C Manual de usuario

Sony

Sony Vaio Series Manual de usuario

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Manual de usuario

Alto

Alto MD 250 Manual de usuario

Lenovo

Lenovo ThinkCentre Edge 72 Manual

Lenovo

Lenovo ThinkStation D20 Manual

Arbor Technology

Arbor Technology FPC-7800 Series Manual de usuario

Sony

Sony VAIO VGX-TP1 Series Manual de usuario

Asus

Asus Eee Box B204 Manual de usuario

Dell

Dell Optiplex 9010 All In One Manual de usuario