Mount-It! MI-4882 Manual de usuario

HEAVY-DUTY DUAL MONITOR ARM

FOR LARGE SCREENS

MI-4882

Please scan this QR code

to visit the product page.

Thank you for choosing Mount-It

Mount-It!

Mount and Accessories

Mounting Hardware

Spring Arms Grommet Plate Clamping Plate

VESA

Connector

Washer

VESA

Connector

Bolt

Bolt Hex Wrench Hex Wrench

Clamp L-Bracket Clamp Screw

Assembly

VESA Heads Clamp Cover Adhesive Pad

Missing Parts? Call us at (855) 925-5668 and we will ship replacement parts free of charge.

CHOKING HAZARD. Package includes small parts.

Not for children under 3 years. Adult supervision is required.

Check carefully to make sure there are no missing or defective parts. Some hardware provided may not

be used. Use the correct mounting hardware suitable for your installation.

DIMENSIONS & WEIGHT CAPACITY

Rated weight capacity

is 44lbs for each mount.

Caution:

Ensure all mounting

surfaces are capable

of holding the weight

of your mount.

DO NOT EXCEED

MAXIMUM LISTED

WEIGHT CAPACITY.

SERIOUS INJURY OR

PROPERTY DAMAGE

MAY OCCUR!

min8.5”~max19.7”

4”

min0.4”

~max1.9”

min0.4”~max3.3”

min9.3”~max11.1”

6.9”4” 3.3”

4.6”

3.9”

3”

4.6”

3.9”

3”

• Use 6mm Hex Wrench (#M) to loosen the bolts on the Clamp Screw Assembly (#A) until the threads on

the bolts are almost fully into the plate, as shown. Place Clamping Plate (#H) onto the tips of the bolts.

• Connect Clamp L-Bracket (#B) to the base of the spring arms using Bolts (#K) and tighten until secure

with Hex Wrench (#L).

• Peel off the backing from Adhesive Pad (#F) and stick it onto the installed Clamp L-Bracket as shown.

Clamp Installation

Step 2a

• Connect the Clamp Screw Assembly onto the back of the L-Bracket. The four screws on the backside

may need to be loosened so that there is a gap of approximately ¼in between the bracket and the bolt

head.

• For desks with a thickness between 50-85mm (1.96”-3.34”) attach the Clamp Screw Assembly to the

lower 4 holes of the Clamp L-Bracket.

• For desks with a thickness between 10-55mm (0.39”-2.16”) attach the Clamp Screw Assembly to the

lower 4 holes of the Clamp L-Bracket.

Cut the Cable Tie

Step 1

• Ensure the four bolts are fully seated in the smaller end of the keyhole mounting holes then tighten until

secure using Hex Wrench (#L).

• Place the assembled mount arms over the edge of the desk in the desired location then tighten the two

clamping bolts until they are secure and the clamp does not move.

Note: Alternate between the two bolts to keep the clamping plate level and for a more secure

installation.

0.2”

1.96”~3.34”

0.39”~2.16”

• Connect Grommet Plate (#F) to the base of the spring arms using Bolts (#K) and tighten until secure

with Hex Wrench (#L).

• Peel off the backing from Adhesive Pad (#F) and stick it onto the installed Grommet Plate as shown.

• Use the Hex Wrench (#M) to fully remove both bolts from the Clamp Screw Assembly (#C). Insert both

bolts into the large outer holes of the Clamping Plate (#H).

Grommet Installation

Step 2b • A grommet hole of .4-2.35in is required to install this mount. If one is not present in the desktop one can be

drilled using a 3/8” drill bit.

• Place the mount over the grommet hole and install the Clamping Plate through the underside of the desktop.

Tighten the bolt until secure using the Hex Wrench (#M).

Note: Alternate between the two bolts to keep the clamping plate level and for a more secure

installation.

Connect the VESA Head to the Spring Arm

Step 3

• Connect the VESA Heads (#D) to the end of the Spring Arms using VESA Connector Washers (#I) and

VESA Connector Bolts (#J). Tighten until secure using the Hex Wrench (#M).

Note: Ensure the Washersare oriented so that the hexagonal interior end is facing upwards, as

illustrated here.

• Remove the thumb screw from the back of the VESA Head, pull the bottom of the VESA Plate on the front

away then up to remove it.

0.4-2.35in

0.4-1.89in

1.8in

• Select the appropriate size mounting bolt (#M-A, M-B) for your monitorsmounting holesand verify the

length of the VESA bolt is not too long. If you are unsure of the correct bolt size for your display refer to

your monitor user manual or contact the monitor manufacturer for sizing information.

• Install the VESA Plate onto the back of the monitor using the selected Bolts (#M-A or M-B) and Washers

(#M-C) and ensure that the arrow on the plate is pointing up to the top of the monitor.

Attach the VESA Plate to the Monitor

Step 4

• Gas Spring tension may need to be adjusted to suit the weight of the monitors. To weight balance the

two gas spring arms,begin by pushing the arm down to the lowered position,then use Hex Wrench (#M)

to adjust the nut as pictured above, turning counterclockwise toward the + (plus) sign for heavier monitors,

increasing the tension and clockwise toward the – (minus) sign for lighter monitors, lowering the tension.

Adjust until the arm does notraise back to the highest position or sink to the lowest position when released.

This might require multiple rotations to reach the desired tension.

Weight Balancing the Gas Spring Arm

Step 6

• Remove the cable management cover from the underside of the spring arm by squeezing both sides of

the cover and then pulling it out. Run any cables beneath then reinstall the cable management cover.

Cable Management

Step 7

• Hang the monitor on the end of the VESA Head by hooking the top of the plate back onto the end of the

arm, and then lower it down into position. Reinstall the thumb screw to secure it in place.

Attaching the Monitor

Step 5

Attach the Clamp Cover (#C) to the

rear of the clamp to utilize the cable

management clips and to store the

Hex Wrenches.

Note: If the monitor tilts forward

on its own or is too difficult to tilt

adjust the tightness of the bolt

indicated here.

Lighting Functions

1. On/Off: Press and hold for 2

seconds to turn on/off

2. Light Mode: Press to cycle

through light modes (20 modes in

total)

3. Random Color: Double press for a

random light mode

4. Memory: The system automatically

stores the last used lighting mode

Plug the USB cable into a USB

outlet such as on a computer,

power strip, or similar.

Tabla de contenidos

Otros manuales de Rack y soporte de Mount-It!

Mount-It!

Mount-It! MI-5761 Manual de usuario

Mount-It!

Mount-It! MI-2752 Manual de usuario

Mount-It!

Mount-It! MI-754 Manual de usuario

Mount-It!

Mount-It! MI-7931 Manual de usuario

Mount-It!

Mount-It! MI-391 Manual de usuario

Mount-It!

Mount-It! MI-763 Manual de usuario

Mount-It!

Mount-It! MI-705 Manual de usuario

Mount-It!

Mount-It! 2781 Manual de usuario

Mount-It!

Mount-It! MI-7264 Manual de usuario

Mount-It!

Mount-It! MI-7610 Manual de usuario

Mount-It!

Mount-It! MI-310 Manual de usuario

Mount-It!

Mount-It! MI-4200 Manual de usuario

Mount-It!

Mount-It! MI-751 Manual de usuario

Mount-It!

Mount-It! MI-2041 Manual de usuario

Mount-It!

Mount-It! MI-2041L Manual de usuario

Mount-It!

Mount-It! MI-2171L Manual de usuario

Mount-It!

Mount-It! MI-850 Manual de usuario

Mount-It!

Mount-It! MI-7916 Manual de usuario

Mount-It!

Mount-It! MI-1753 Manual de usuario

Mount-It!

Mount-It! MI-792 Manual de usuario

Mount-It!

Mount-It! MI-5352T Manual de usuario

Mount-It!

Mount-It! MI-2757 Manual de usuario

Mount-It!

Mount-It! MI-394 Manual de usuario

Mount-It!

Mount-It! MI-390 Manual de usuario

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario