Mount-It! 2781 Manual de usuario

English

Installation Instruction

UNPACKING INSTRUCTIONS

!Carefully open the carton, remove contents and lay out on cardboard or other

protective surface to avoid damage.

!Check package contents against the Supplied Parts List in the next page to assure

that all components were received undamaged. Do not use damaged or defective

parts.

!Carefully read all instructions before attempting installation.

IMPORTANT SAFETY INFORMATION

!Install and operate this device with care. Please read this instruction before

installation, and carefully follow all instructions contained herein. Use proper safety

equipment during installation.

!Please call a qualified installation contractor for help if you don't understand these

directions or have any doubts about the safety of the installation.

Do not use this product for any purpose or in any configuration not explicitly specified

in this instruction. We hereby disclaims any and all liability for injury or damage

arising from incorrect assembly, incorrect mounting, or incorrect use of this product.

Supplied Par ts List

CAUTION!

WARNING

!The monitor desktop mount must be evenly positioned on a

stable horizontal surface. If the mount is not positioned in a

balanced manner, it may fall, resulting in possible injury

and/or damage. The optional desktop bolt may be used to

provide additional stability.

(1)Support Plate-j(1)M10 Bolt-i (1)M10 Washer-k (1)Spring Washer-l

(8)M4 Spacer-s(8)M4x12 Bolt-q (8)M4x30 Bolt-r

(1) Grommet Base

Plate-m (1)Wire Clip-n1 (1)Allen Key-o

(1)Wrench-p

Tools Required Phillips Screwdriver

(4)Wire Clip-n2

(1) Pole-a (1) Swivel Arm-c(1) Weighted Base-b

(2) VESA Plate-d (2) Nut-h

(3) M5x14 Bolt-e

Step 1 Install the Pole to the Desktop

Option A: Weighted Base Install

1. Install the Pole(a) to the Weighted

Base(b) using 3pcs M5x14 Bolts(e), and

tighten using the Allen Key(o), see Figure 1.

2. Optionally, you can drill a 10mm diameter

hole in your desk and secure using the

Support Plate (j), M10 Washer(k), Spring

Washer(l) and M10 Bolt(i). Fasten the M10

Bolt with provided Wrench(p), see Figure 2.

Figure 2

Option B: Grommet Base Install

If the existing grommet hole comes with a

plastic protector, remove it to ensure a flat

surface before installing the desk mount.

1. Install the Grommet Base Plate(m) to the

Pole(a) using 3pcs M5x14 Bolts(e), and

tighten using the Allen Key(o), see Figure 3.

2. Position the Pole(a) on the mounting

surface and secure using the Support Plate

(j), M10 Washer(k), Spring Washer(l) and

M10 Bolt(i). Fasten the M10 Bolt using

provided Wrench(p), see Figure 4.

Figure 3

Figure 4

Existing Grommet Hole Installation

Figure 1

Step 1 Install the Pole to the Desktop

Self Drilled Grommet Hole Installation

Option B: Grommet Base Install

1. Position the Pole(a) on the mounting

surface and mark the center hole. Drill a 3/8"

(10mm) diameter hole at the marked position

through the mounting surface.

2. Install the Grommet Base Plate(m) to the

Pole(a) using 3pcs M5x14 Bolts(e), and

tighten using the Allen Key(o), see Figure 5.

3. Position the Pole(a) on the mounting

surface and secure using the Support Plate

(j), M10 Washer(k), Spring Washer(l) and

M10 Bolt(i). Fasten the M10 Bolt using

provided Wrench(p), see Figure 6.

Figure 5

Figure 6

Step 2 Install Arm to the Pole

Install Swivel Arm(c) to the

Pole(a). Fasten the bolt with

supplied Allen Key(o). Attach

the Wire Clip(n1,n2) to the

Pole(a) and Swivel Arm(c).

Step 3 Attach the VESA Plate to the Monitor

For Monitor with Curved or

Recessed Back

Step 4 Slide the Monitor onto the Head of Swivel Arm

Install the security Nut(h). Make

sure the security nut is installed

before you rotate the monitor.

Slide the monitor onto the head of

Swivel Arm(c) as shown in the

above diagram.

For Monitor with Flat Back

Step 6 Make the Necessary Adjustments and Manage the Wires

Step 5 Fix the Tilt Angle and Adjust the Level of Monitor

Use the supplied Allen Key(o) to make

the necessary adjustments.

Tighten the bolt with the supplied Allen

Key(o) to fix the tilt angle.

Fix the tilt angle

Thank you for choosing our products!

Ignore this step if

monitors are level

If one monitor is lower, remove the Nut(h) and

turn the bolt counter-clockwise with supplied

Allen key(o) to raise the monitor. Install the

Nut(h) after the adjustment.

Manage the wires and store the Allen

keys(o) in Wire Clip(n1) for future use.

Tabla de contenidos

Otros manuales de Rack y soporte de Mount-It!

Mount-It!

Mount-It! MI-2752 Manual de usuario

Mount-It!

Mount-It! MI-751 Manual de usuario

Mount-It!

Mount-It! MI-706 Manual de usuario

Mount-It!

Mount-It! MI-7264 Manual de usuario

Mount-It!

Mount-It! MI-2789 Manual de usuario

Mount-It!

Mount-It! MI-1753 Manual de usuario

Mount-It!

Mount-It! MI-2171L Manual de usuario

Mount-It!

Mount-It! MI-386 Manual de usuario

Mount-It!

Mount-It! MI-390 Manual de usuario

Mount-It!

Mount-It! MI-2041 Manual de usuario

Mount-It!

Mount-It! MI-4753B Manual de usuario

Mount-It!

Mount-It! MI-763 Manual de usuario

Mount-It!

Mount-It! MI-2041L Manual de usuario

Mount-It!

Mount-It! MI-4200 Manual de usuario

Mount-It!

Mount-It! MI-850 Manual de usuario

Mount-It!

Mount-It! MI-772 Manual de usuario

Mount-It!

Mount-It! MI-390 Manual de usuario

Mount-It!

Mount-It! MI-2757 Manual de usuario

Mount-It!

Mount-It! MI-5352T Manual de usuario

Mount-It!

Mount-It! MI-2751 Manual de usuario

Mount-It!

Mount-It! MI-792 Manual de usuario

Mount-It!

Mount-It! MI-310 Manual de usuario

Mount-It!

Mount-It! MI-4882 Manual de usuario

Mount-It!

Mount-It! MI-725 Manual de usuario

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario